DLA MS52143-1980 BEARING ROLLER NEEDLE THICK OUTER RING W ROLLERS CAGE AND SEALS《厚外环W 滚柱 定位圈和密封滚针滚柱轴承》.pdf

《DLA MS52143-1980 BEARING ROLLER NEEDLE THICK OUTER RING W ROLLERS CAGE AND SEALS《厚外环W 滚柱 定位圈和密封滚针滚柱轴承》.pdf》由会员分享，可在线阅读，更多相关《DLA MS52143-1980 BEARING ROLLER NEEDLE THICK OUTER RING W ROLLERS CAGE AND SEALS《厚外环W 滚柱 定位圈和密封滚针滚柱轴承》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、MS523Ll3 33 W 9999732 00061167 2 = I f ED. SUP CLASS 3110 , RADIUS (SEE NOTE OIL GROOVE AND ONE TO FOUR OIL HOLES IN ACCORDANCE VI HANUFACTURERS STANDARD PRACTICE. 01 g e kQ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FED. SUP CLASS 3111) PROTECT

2、IVE COATING - UNLESS OTHERWISE SPECIFIED, PLAIN (NOT PLATED) BEARINGS TO BE COATE3 WITH RUST PREVENTIVE FILM BY MANUFACTURER. LUBRICATION - BEARINGS SHALL BE FURNISHED WITHOUT LUBRICATION. NOTES: 1. 2. 3. 9. 5. 6. 7. 8. 9. 10. 11. 12. ia. 14, 16. 16. ALL DIMENSIONS ARE IN INCHES. BEARINGS ARE INTEND

3、ED TO BE INSTALLED ON SHAFTS WHERE HAXIMUM TAPER DOES NOT EXCEED ,0005 INCHES PER INCH OF BEARING WIDTH. BMRC BOE SBOIILD BE UmlR TRE NEEDLE LoutRs, MD A “R3 a“ ILW CAGE .O001 I1Kn UECER BAN TUE KUI(uII DIMEIER iDl! iBE *POLL IDLLtRs. IISIWC A “CU“ ILDC CACE OF TUE SIZE .MO1 LESS W iBE WIHIWUW DUIIL

4、IER IE “iI, CU“ WE WT UTE4 25 OF MUER I-. ONE END OF BEARING MUST CLEAR THE MAXIMUM HOUSING FILLET RADIUS SHOWN IN “RAD“ COLUMN. 1/32 HINIHUM CHAMFER ON OPPOSITE END MAY BE USED IN LIEU OF “RAD“ CLEARANCE. WHEN ESDS ARE NOT IDENTICAL, THE MARKING (NOTE 8) SHALL BE APPLIEE TO TFIC END wi:? THE LARGES

5、T SURTAX. SEAL OPERATING INFORMATION - MINIHUH OPERATING TETERATURE MINUS 30 F AND THE HAXIHUII OPERATING SPEED SHOULD NOT EXCEED 1000 FEET PER HINUTE. PROVISIONS FOR LEAD OR RADIUS SHOULD BE MADE ON SHAFT CORNER TO FACILITATE ASSEHBLY OF SEALED BEARINGS OF THE “RS“ AND “SRS“ CONFIGURATION. VENTING

6、OF RELUBRICATION PRESSURE IS REQUIRED TO AVOID DISPLACEMENT OS SEALS IN THE “S“ OR “SS“ CONFIGURATION. TEMPERATURE SHOULD NOT EXCEED zsoo F CONSTANT, 300 r INTERMITTENT. HAXIHUIJ PERIPHERAL SHAFT BEARINGS ARE INTENDED TO BE USED WITH HARDENED SHAFTS RC 58-65. FOR USE WITH UNHARDENED SHAFTS, BEARING

7、SHOULD BE USED IN CONJUNCTION WITH RING, BEARING, INNER. HS51962. TEE PE ?ART MER 6RN.L 03EISI OF iBE Kc DASR NCWER, ILUS iBE SW CONFIGURATION CODING. WLE: Kc52143-2-RSS “S“ - SINGLE SEAL, LIP INWARD “SS“ - DOUBLE SEAL, LIPS INWARD “RS“ - SINGLE SEAL, LIP OUTWARD “RSS“ - WUBLE SEAL, LIPS OUTWARD “SRS“ - WUBLE SEAL, ONE LIP INWARD AND ONE LIP OUTWARD. THE HARKING SHALL CONSIST OF THE HS PART NUHBER AND THE MANUFACTURE Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-