DLA MS13804 REV D-1991 GENERATOR ENGINE ACCESSORY D C 28-VOLT 40-AMP《28伏40安培直流发动机装配发电机》.pdf

《DLA MS13804 REV D-1991 GENERATOR ENGINE ACCESSORY D C 28-VOLT 40-AMP《28伏40安培直流发动机装配发电机》.pdf》由会员分享，可在线阅读，更多相关《DLA MS13804 REV D-1991 GENERATOR ENGINE ACCESSORY D C 28-VOLT 40-AMP《28伏40安培直流发动机装配发电机》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、r MS13884 REV D 29 H 9799912 OOL23L9 2 H 4 12.37 MAX. r ELBOW-ATAC NO. 7716690 - BEARING COVER PLATE AND PLATE SCREWS SHALL NOT EXTEND BEYOND LIMITS INDICATED BY DOTTED LINES _ .53 .43 NEGATIVE GROUND 2 50 2 5 3 20 F 10 9 40 RI 30 II 0: o 1000 2000 3000 4000 5000 R.P.M. MINIMUM GENERATOR PERFORMANCE

2、 AT 77“ AMBIENT WITH FULLY SEATTD BRUSHES. PERFORMANCE CHARACTERISTICS: 1. hlAXlMUM RECOMMENDED OPERATING SPEED-4000 RPM. 3. GENERATOR PERFORMANCE WHEN USED WITH REGULATOR, 2. MAXIMUh4 INTERMITTENTTOP SPEED-SOO0 RPM. PART NO. MS13003-1. RECOMMENDED CLAMPING SPACE SELF LOCKING UNF THREAD NUT .625-18

3、GENERATOR, ENGINE AcCFssnRv D.C., 28-VOLT, - . -. I 40-AMP FORM DD1SEP57 e72 AMSC NIA PREVIOUS EDITIONS OF THIS FORM ARE OBSOLETE 2910 - O189 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I FED. SUP CLAS! I 2920 NOTES: 1. THIS GENERATOR IS IDENTIFI

4、ED BY PART NOS 7344736 AND 10950808 OF REFERENCED PROCUREMENT SPECIFICATION. 2. SPLINE DATA. GENERAL i “13 TEETH, 16/32 PITCH. 30“ PRESSURE ANGLE; .ai25 PITCH DIAMETER. INTERNAL - SHALL BE TRUE INVOLUTE INSIDE GIVEN DIAME. TER OF 8676 1963 CIRCULAR PITCH. 0994/ .O982 T .7582/.7533MINOR IMETER; ,6533

5、 MAX. OVER .lo8 DIAMETER EXTERNAL - HLL BE TRUE INVOLUTE OUTSIDE GIVEN DIAMETER OF 7493. 1963 CIRCULAR PITCH: .8636/.8586 MbOR 6iAMETER: .7335/.7225 MINOR DIAMETER: .9896/.9859 BETWEEN ,120 DIAMETER PINS MODIFICATIONS IN OUTSIDE APPEARANCE AND CONSTRUCTION SHALL BE ACCEPTABLE IF UNIT INTERCHANGEABIL

6、ITY IS NOT AFFECTED. DESIGN OF COOLING FAN USED WITH THIS GENERATQR WILL VARY WITH APPLICATION. CONSULT GENERATOR MANUFAC- TURER FOR CORRECT COOLING FAN DESIGN PROTECTED BOTH INSIDE AND OUTSIDE WITH A LABYRINTH FOR DESIGN FEATURE PURPOSES THIS STANDARD TAKES BOTH THE COMMUTATOR AND DRIVE-END BEARING

7、S SHALL BE TYPE DUST QHIELD. PRECEDENCE OVER PROCUREMENT DOCUMENTS REFERENCED HFRFIN . .-. .-., (0) 7. UNLESS OTHERWISE INDICATED COPIES OF FEDERAL AND MILITARY FROM THE STANDARDIZATIONDOCUMENTS ORDER DESK, BUILDING 413. IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF THIS DOCUMENT AND THE REFERENCES

8、 CITED HEREIN THE TEXT OF THIS DOCUMENT TAKES PRECEDENCE NOTHING IN THS DOCUMENT HOWEVER, SPECIFIC EXEMPTION HAS BEEN OBTAINED. SPECIFICATIONS STANDARDS AND HANDBOOKS ARE AVAILABLE 700 ROBBINS AVENUE PHILADELPHIA, PA 1911 1-5094. 8. ALL DIMENSIONS AREIN INCHES. 9. SUPERSEDES APPLICABLE LAWS AND REGU

9、LATIONQ UNLESS A DENOTES CHANGE _ MS1380q REV D 27 = 7977712 0012320 7 I PREVIOUS EEITIONS OF THIS FORM ARE OBSOLETE FORM AMSC NIA DDISEP 57 672 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FED. SUP CLASS 2920 ROTATION C. W. DRIVE END VIEW 4.437

10、I.062 COMMUTATOR END VIEW .A. ARMY ME INTERNATIONAL TITLE INTEREST GENERATOR, ENGINE ACCESSORY, D.C., 28-VOLT, 40-AMP PREViUS EBITIONS OFTHIS FOBM ARE OBSOLETE FORM MILITARY STANDARD MS13804 3 OF 3 SHEET 672 iSEP57 DD AMSC MA Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-