DLA MIL-DTL-83723 89 F-2010 CONNECTORS ELECTRICAL (CIRCULAR ENVIRONMENT RESISTING) RECEPTACLE (SINGLE HOLE MOUNT THREADED COUPLING SOLDER PIN CONTACT) (SERIES III CLASSES H J L N P.pdf

《DLA MIL-DTL-83723 89 F-2010 CONNECTORS ELECTRICAL (CIRCULAR ENVIRONMENT RESISTING) RECEPTACLE (SINGLE HOLE MOUNT THREADED COUPLING SOLDER PIN CONTACT) (SERIES III CLASSES H J L N P.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-83723 89 F-2010 CONNECTORS ELECTRICAL (CIRCULAR ENVIRONMENT RESISTING) RECEPTACLE (SINGLE HOLE MOUNT THREADED COUPLING SOLDER PIN CONTACT) (SERIES III CLASSES H J L N P.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, (CIRCULAR, ENVIRONMENT RESISTING), RECEPTACLE, (SINGLE HOLE MOUNT, THREADED COUPLING, SOLDER PIN CONTACT), (SERIES III, CLASSES H, J, L, N, P AND Y) This specification is approved for use by all Departments and Agencies of the Department of Defense

2、. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83723. FIGURE 1. Dimensions and configurations. AMSC N/A FSC 5935 INCH-POUND MIL-DTL-83723/89F 1 October 2010 SUPERSEDING MIL-DTL-83723/89E 23 May 2003 Provided by IHSNot for ResaleNo

3、reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/89F 2 FIGURE 1. Dimensions and configurations Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/89F 3 Shell size A thread B C D E F 8 .562-24 UNEF-

4、2A .394 .418 / .413 .290 .562 .137 / .097 10 .688-24 UNEF-2A .515 .535 / .530 .388 .696 .137 / .097 12 .875-20 UNEF-2A .685 .700 / .705 .558 .875 .137 / .097 14 .938-20 UNEF-2A .754 .774 / .769 .627 .936 .137 / .097 16 1.062-18 UNEF-2A .881 .901 / .896 .772 1.062 .137 / .097 18 1.188-18 UNEF-2A .987

5、 1.007 / 1.002 .860 1.187 .137 / .097 22 1.438-18 UNEF-2A 1.237 1.257 / 1.252 1.110 1.437 .148 / .128 Shell size M thread N P R W X 8 .625-20 UN-2A .670 .980 / .949 1.078 / 1.047 .400 .180 / .120 10 .750-20 UNEF-2A .796 1.104 / 1.073 1.192 / 1.162 .411 .180 / .120 12 .938-20 UNEF-2A .984 1.291 / 1.2

6、60 1.380 / 1.349 .581 .180 / .120 14 1.000-20 UNEF-2A 1.046 1.391 / 1.360 1.516 / 1.485 .650 .180 / .120 16 1.125-18 UNEF-2A 1.171 1.516 / 1.485 1.641 / 1.610 .777 .180 / .120 18 1.250-18 UNEF-2A 1.296 1.641 / 1.610 1.766 / 1.735 .864 .180 / .120 22 1.500-18 UNEF-2A 1.609 1.954 / 1.923 2.078 / 2.047

7、 1.133 .169 / 1.09 FIGURE 1. Dimensions and configurations Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/89F 4 Shell size Y CC + .005 - .000 DD EE FF JJ 8 .210 / .150 .490 .076 / .071 .605 .635 .596 / .590 10 .210 / .150 .6

8、36 .089 / .084 .730 .760 .721 / .715 12 .210 / .150 .806 .089 / .084 .917 .947 .908 / .902 14 .210 / .150 .875 .089 / .084 .980 1.010 .971 / .965 16 .210 / .150 1.002 .089 / .084 1.105 1.135 1.096 / 1.090 18 .210 / .150 1.108 .089 / .084 1.230 1.260 1.220 / 1.214 22 .199 / .139 1.358 .089 / .084 1.4

9、80 1.510 1.470 / 1.464 NOTES: (Notes 4 through 9 applicable to contacts only). 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 inches (0.13 mm) for three place decimal, .01 inches (0.25 mm) for two place decimals,

10、and 1 for all angles. 4. Contact finish: Gold plate .000050 inch (0.00127 mm) minimum in accordance with ASTM B488. A suitable underplating shall be used. Silver shall not be used. Finish is applied after sealing. 5. Dimensions apply after plating. 6. Surface finish: 63 ( ) all over in accordance wi

11、th ASME-B46.1 , unless otherwise specified. 7. Remove all burrs and sharp edges .003 to .005 inches (0.076 to 0.127 mm) R. 8. Diameters to be concentric within .004 inches (0.102 mm) TIR. 9. Diameters in the same cross-sectional plane to be concentric with each other .003 inches (0.076 mm) TIR. 10.

12、Coupling indicator line shall be color coded red. 11. Shell size 8 will not mate with MIL-DTL-26500 connectors. 12. See table I for contact cavities requiring this dimension. FIGURE 1. Dimensions and configurations Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted witho

13、ut license from IHS-,-,-MIL-DTL-83723/89F 5 Inches mm Inches mm Inches mm Inches mm Inches mm .000050 0.00127 .137 3.48 .558 14.17 .901 22.89 1.192 30.28 .003 0.08 .138 3.51 .562 14.27 .902 22.91 1.214 30.84 .004 0.10 .139 3.53 .581 14.76 .908 23.06 1.220 30.99 .005 0.13 .144 3.66 .590 14.99 .917 23

14、.29 1.230 31.24 .015 0.38 .148 3.76 .596 15.14 .918 23.31 1.237 31.42 .018 0.46 .150 3.81 .605 15.37 .929 23.60 1.250 31.75 .019 0.48 .169 4.29 .627 15.93 .936 23.77 1.252 31.80 .020 0.51 .180 4.57 .635 16.13 .947 24.05 1.257 31.93 .022 0.56 .198 5.03 .636 16.15 .949 24.10 1.260 32.00 .025 0.64 .199

15、 5.05 .650 16.51 .965 24.51 1.291 32.79 .032 0.81 .204 5.18 .670 17.02 .971 24.66 1.296 32.92 .050 1.27 .210 5.33 .685 17.40 .980 24.89 1.349 34.26 .054 1.37 .265 .673 .696 17.68 .984 24.99 1.358 34.49 .062 1.57 .281 7.14 .700 17.78 .987 25.07 1.360 34.54 .063 1.60 .290 7.37 .705 17.91 1.002 25.45 1

16、.380 35.05 .071 1.80 .329 8.36 .708 17.98 1.007 25.58 1.391 35.33 .076 1.93 .340 8.64 .715 18.16 1.010 25.65 1.437 36.50 .078 1.98 .351 8.92 .721 18.31 1.046 26.57 1.464 37.19 .084 2.13 .388 9.86 .730 18.54 1.047 26.59 1.470 37.34 .089 2.26 .394 10.01 .760 19.30 1.062 26.97 1.480 37.59 .090 2.29 .40

17、0 10.16 .761 19.33 1.073 27.25 1.485 37.72 .092 2.34 .411 10.44 .769 19.43 1.078 27.38 1.510 38.35 .093 2.36 .413 10.49 .772 19.61 1.090 27.69 1.516 38.51 .097 2.46 .418 10.62 .774 19.66 1.096 27.84 1.572 39.93 .098 2.49 .424 10.77 .777 19.74 1.104 28.04 1.609 40.87 .100 2.54 .433 11.00 .781 19.84 1

18、.105 28.07 1.610 40.89 .106 2.69 .461 11.71 .796 20.22 1.108 28.14 1.641 41.68 .109 2.77 .481 12.22 .806 20.47 1.110 28.19 1.735 44.07 .112 2.84 .490 12.45 .860 21.84 1.133 28.78 1.766 44.86 .118 3.00 .515 13.08 .864 21.95 1.135 28.83 1.923 48.84 .120 3.05 .518 13.16 .875 22.23 1.162 29.51 1.954 49.

19、63 .125 3.18 .530 13.46 .881 22.38 1.171 29.74 2.047 51.99 .128 3.25 .535 13.59 .896 22.76 1.187 30.15 2.078 52.78 FIGURE 1. Dimensions and configurations Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/89F 6 REQUIREMENTS Dim

20、ensions and configurations: See figure 1. This connector mates with MIL-DTL-83723/86, /91, /95, and /97. Insert arrangements and polarizing positions: See MIL-STD-1554 and table I. TABLE I. Insert arrangements requiring reduced diameters for raised seal barriers on contact cavities as indicated. She

21、ll size Insert arrangement Contact cavities 8 03, 98 1, 2, 3 10 06 1, 2, 3, 4, 5, 6 Connector accessories: See SAE-AS85049. O-ring: See MIL-DTL-83723. Part or Identifying Number (PIN) example: M83723/ 88 H 22 55 N Military designation Specification sheet number Class Shell size Insert arrangement Po

22、larizing position Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-83723, this document references the following: MIL-DTL-26500 MIL-DTL-8

23、3723/86 MIL-DTL-83723/91 MIL-DTL-83723/95 MIL-DTL-83723/97 MIL-STD-1554 MS3186 ASME-B46.1 ASTM B488 SAE-AS85049 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/89F 7 CONCLUDING MATERIAL Custodians: Preparing activity: Army CR DLA CC Nav

24、y AS Air Force 85 (Project 5935-2010-052) DLA CC Review activities: Army AR, AV, MI Navy EC Air Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-