DLA MIL-DTL-83528 9 E-2013 GASKETING MATERIAL CONDUCTIVE SHIELDING GASKET ELECTRONIC ELASTOMER EMI RFI SOLID RECTANGULAR-STRIP.pdf

《DLA MIL-DTL-83528 9 E-2013 GASKETING MATERIAL CONDUCTIVE SHIELDING GASKET ELECTRONIC ELASTOMER EMI RFI SOLID RECTANGULAR-STRIP.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-83528 9 E-2013 GASKETING MATERIAL CONDUCTIVE SHIELDING GASKET ELECTRONIC ELASTOMER EMI RFI SOLID RECTANGULAR-STRIP.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-DTL-83528/9E 27 November 2013 SUPERSEDING MIL-DTL-83528/9D 15 November 2001 DETAIL SPECIFICATION SHEET GASKETING MATERIAL, CONDUCTIVE, SHIELDING GASKET, ELECTRONIC, ELASTOMER, EMI/RFI, SOLID RECTANGULAR-STRIP This specification is approved for use by all Departments and Agencies of the Departme

2、nt of Defense. The requirements for acquiring the relay described herein shall consist of this specification and the latest issue of MIL-DTL-83528. NOTE: Length shall be as specified on the purchase order. FIGURE 1. EMI/RFI gasket, elastomer, solid rectangular strip. AMSC N/A FSC 5999 INCH-POUND Pro

3、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/9E 2 REQUIREMENTS: Design and interface: See figure 1 and table I. Material: Type A, B, C, D, E, F, H, J, K, L, or M. Part or Identifying Number (PIN): See table I. Supersession information:

4、See table II. TABLE I. Dimensions. PIN 1/ M83528/009X Nominal dimensions 2/ 3/ Cross section area (cm2) 4/ A (width) B (height) 001 0.063 (1.60) 0.042 (1.07) 0.017 002 0.095 (2.41) 0.062 (1.57) 0.038 003 0.120 (3.05) 0.075 (1.91) 0.058 004 0.125 (3.18) 0.062 (1.57) 0.050 005 0.156 (3.96) 0.062 (1.57

5、) 0.062 006 0.250 (6.35) 0.062 (1.57) 0.100 007 0.500 (12.70) 0.062 (1.57) 0.242 008 0.500 (12.70) 0.075 (1.91) 0.403 009 0.500 (12.70) 0.188 (4.78) 0.606 010 0.750 (19.05) 0.062 (1.57) 0.300 011 0.880 (22.35) 0.062 (1.57) 0.352 012 1.000 (25.40) 0.250 (6.35) 1.613 013 1.180 (29.97) 0.062 (1.57) 0.4

6、72 1/ “X” in the PIN shall be replaced by the applicable material type. Complete PIN example: M83528/009A001. 2/ Dimensions are in inches; metric equivalents are given in parenthesis and are for general information only. 3/ Tolerance shall be as follows: Dimensions Tolerance Under Over .101 (2.57) .

7、101 to .200 (2.57 to 5.08) .201 to .300 (5.10 to 7.62) .301 to .500 (7.62 to 12.70) .500 (12.70) .005 (0.13) .008 (0.20) .010 (0.25) .015 (0.38) .020 (0.51) 4/ For calculation of volume resistivity (for reference only). Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

8、ense from IHS-,-,-MIL-DTL-83528/9E 3 TABLE II. Supersession information. PIN 1/ M83528/009X Superseded DESC Drawing PIN 85108X 1/ 001 001002 002003 003004 004 005 005006 006007 007008 008 009 009010 010011 011012 012 013 0131/ “X” in the PIN indicates the applicable material type. Changes from previ

9、ous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are caution

10、ed to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. This document references MIL-DTL-83528: Custodian: Preparing activity: Army CR DLA CC Navy EC Air Force 85 (Project 5

11、999-2013-020) DLA CC Review activities: Air Force 19, 99 NSA NS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/ . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-