DLA MIL-DTL-83528 7 F-2013 GASKETING MATERIAL CONDUCTIVE SHIELDING GASKET ELECTRONIC ELASTOMER EMI RFI HOLLOW D-STRIP.pdf

《DLA MIL-DTL-83528 7 F-2013 GASKETING MATERIAL CONDUCTIVE SHIELDING GASKET ELECTRONIC ELASTOMER EMI RFI HOLLOW D-STRIP.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-83528 7 F-2013 GASKETING MATERIAL CONDUCTIVE SHIELDING GASKET ELECTRONIC ELASTOMER EMI RFI HOLLOW D-STRIP.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-DTL-83528/7F 10 September 2013 SUPERSEDING MIL-DTL-83528/7E 15 November 2001 DETAIL SPECIFICATION SHEET GASKETING MATERIAL, CONDUCTIVE, SHIELDING GASKET, ELECTRONIC, ELASTOMER, EMI/RFI, HOLLOW D-STRIP This specification is approved for use by all Departments and Agencies of the Department of De

2、fense. The requirements for acquiring the relay described herein shall consist of this specification sheet and the latest issue of MIL DTL-83528. NOTE: 1. Dimensions are in inches; metric equivalents are given in parenthesis and are for general information only. 2. Length shall be as specified on th

3、e purchase order. FIGURE 1. EMI/RFI gasket, elastomer, and hollow D-strip. AMSC N/A FSC 5999 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/7F 2 REQUIREMENTS: Design and interface: See figure 1 and table I. Material: Type A,

4、 B, C, D, E, F, H, J, K, L, or M. Part or Identifying Number (PIN): See table I. Supersession information: See table II. TABLE I. Dimensions. PIN 1/ M83528/007X Nominal dimensions 2/ 3/ Configuration Cross section area (cm2) 4/ A B C D 001 .156 (3.96) .078 (1.98) .078 (1.98) .045 (1.14) A 0.116 002

5、.187 (4.75) .093 (2.36) .093 (2.36) .050 (1.27) A 0.156 003 .312 (7.92) .156 (3.96) .156 (3.96) .062 (1.57) A 0.356 004 .312 (7.92) .156 (3.96) .156 (3.96) .062 (1.57) B 0.337 005 .312 (7.92) .200 (5.08) .112 (2.84) .062 (1.57) A 0.334 006 .487 (12.37) .080 (2.03) .244 (6.20) .080 (2.03) A 0.582 007

6、 .250 (6.35) .125 (3.18) .125 (3.18) .065 (1.65) A 0.227 1/ “X” in the PIN shall be replaced by the applicable material type. Complete PIN example: M38528/007A001. 2/ Dimensions are in inches; metric equivalents are given in parenthesis and are for general information only. 3/ Tolerance shall be as

7、follows: Dimensions Tolerance Under .101 (2.57) .101 to .200 (2.57 to 5.08) .201 to .300 (5.10 to 7.62) .301 to .500 (7.62 to 12.70) .005 (0.13) .008 (0.20) .010 (0.25) .015 (0.38) 4/ For calculation of volume resistivity (for reference only). TABLE II. Supersession information. PIN 1/ M83528/007X S

8、uperseded MIL-DTL-83528/7 PIN 85106X 1/ 001 001002 002 003 003004 004 005 005006 006 1/ “X” in the PIN indicates the applicable material type. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/7F 3 Changes from previous issue. The margins

9、 of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the req

10、uirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. This document references MIL-DTL-83528. Custodian: Preparing activity: Army CR DLA CC Navy EC Air Force 85 (Project 5999-2013-015) DLA CC R

11、eview activities: Air Force 19, 99 NSA NS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-