DLA MIL-DTL-83513 19 D-2009 CONNECTORS ELECTRICAL RECTANGULAR RECEPTACLE MICROMINIATURE POLARIZED SHELL RIGHT ANGLE SOCKET CONTACTS 2 ROW SOLDER TYPE STANDARD PROFILE 9 THROUGH 37 .pdf

《DLA MIL-DTL-83513 19 D-2009 CONNECTORS ELECTRICAL RECTANGULAR RECEPTACLE MICROMINIATURE POLARIZED SHELL RIGHT ANGLE SOCKET CONTACTS 2 ROW SOLDER TYPE STANDARD PROFILE 9 THROUGH 37 .pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-83513 19 D-2009 CONNECTORS ELECTRICAL RECTANGULAR RECEPTACLE MICROMINIATURE POLARIZED SHELL RIGHT ANGLE SOCKET CONTACTS 2 ROW SOLDER TYPE STANDARD PROFILE 9 THROUGH 37 .pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5935 MIL-DTL-83513/19D 18 March 2009 SUPERSEDING MIL-DTL-83513/19C 27 February 2003 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, RECTANGULAR, RECEPTACLE, MICROMINIATURE, POLARIZED SHELL, RIGHT ANGLE, SOCKET CONTACTS, 2 ROW, SOLDER TYPE, STANDARD PROFILE, 9 THROUGH 37 CONTACTS, PRI

2、NTED CIRCUIT BOARD This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83513. Inches mm Inches mm Inches mm Inches mm Inches mm INCH-POUN

3、D .003 0.08 .015 0.38 .0671 1.704 .144 3.66 .190 4.83 .0038 0.097 .025 0.64 .096 2.44 .150 3.81 .200 5.08 .005 0.13 .050 1.27 .125 3.18 .185 4.70 .325 8.26 .010 0.25 .05 1.3 .130 3.30 .1852 4.704 .465 11.81 FIGURE 1. Connector, receptacle, 050 inch (1.27mm) spacing. Provided by IHSNot for ResaleNo r

4、eproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/19D 2 FIGURE 1. Connector, receptacle, .050 inch (1.27mm) spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/19D 3 Number of contacts A max

5、 B .005 (0.18) C .005 (0.13) D min 9 1.390 (35.31) 1.150 (29.21) .565 (14.35) .3342 (8.489) 15 1.540 (39.12) 1.30 (33.02) .715 (18.16) .4842 (12.299) 21 1.690 (40.64) 1.450 (36.83) .865 (21.97) .6342 (16.109) 25 1.790 (45.47) 1.550 (39.37) .965 (24.51) .7342 (18.649) 31 2.040 (51.82 1.80 (45.7) 1.11

6、5 (28.32) .8842 (22.459) 37 2.340 (59.44) 2.10 (53.3) 1.265 (32.13) 1.0342 (26.269) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm). 4. Termination organization area to be optionally molded or fill

7、ed with a potting fill material capable of passing the electrical and environmental requirements of MIL-DTL-83513. Plastic molding shall conform to type GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D406

8、7 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 5. Metal shell shall be of material in accordance with MIL-DTL-83513 for class M parts. 6. Jackpost (securely attached) when specified: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A58

9、2M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. Hardware will be attached in such a fashion as to not loosen during normal de-mating conditions, where as, the mating connector hardware does not exceed the following torque values: 2.5 inch pounds for #2-56 (arrange

10、ments A G) and 4.5 inch pounds for #4-40 (arrangement H). 7. Separately molded plastic body (if used) shall conform to type GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F

11、or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 8. Wire termination pins shall conform to A-A-59551, number 24 AWG copper, except shall be tin-lead plated with a minimum of 3 percent lead. 9. Interfacial seals are included with each type receptacle connector. 10. Termination lengths availab

12、le: .109 (2.77 mm), .140 (3.56 mm), or .172 (4.37 mm). The tolerance shall be .015 (0.38 mm) for all termination lengths. 11. Threaded insert, when specified: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with S

13、AE-AMS-2700, type 2. FIGURE 1. Connector, receptacle, .050 inch (1.27mm) spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/19D 4 NOTE: Engaging face of socket insert shown, cavity identification numbers are for refere

14、nce only and do not appear on the part. FIGURE 2. Insert arrangement.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/19D 5 NOTE: Engaging face of socket insert shown, cavity identification numbers are for reference only and do not appea

15、r on the part. FIGURE 2. Insert arrangement - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/19D 6 FIGURE 3. Layout arrangement. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

16、-,-MIL-DTL-83513/19D 7 FIGURE 3. Layout arrangement - Continued.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/19D 8 Inches mm Inches mm Inches mm .020 0.51 .100 2.54 .715 18.16 .040 1.02 .108 2.74 .865 21.97 .050 1.27 .158 4.01 .965 2

17、4.51 .083 2.11 .183 4.65 1.115 28.32 .096 2.44 .565 14.35 1.265 32.13 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerance is .005 (0.13 mm) on decimals. FIGURE 3. Layout arrangement - Continued. Provided by IHSNot for Res

18、aleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/19D 9 REQUIREMENTS: Dimensions and configurations: See figures 1, 2 and 3. Current rating, maximum: 3 amperes per contact. Materials: Termination organization area: Potting fill material capable of passing the elec

19、trical and environmental requirements of MIL-DTL-83513. Shell: The requirements for shell materials shall be in accordance with MIL-DTL-83513. Plastic body or plastic molding: Shall conform to the requirements of GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM

20、D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. Jackpost: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-

21、AMS-2700, type2. Wire termination pins: Wire termination pins shall conform to A-A-59551, no. 24 AWG copper, except shall be tin-lead plated with a minimum of 3 percent lead. Mating connector: Shall conform to MIL-DTL-83513/1 and MIL-DTL-83513/3. Plating of termination leads: Solder dipping of termi

22、nation leads will be accomplished in SN60 PB40 or SN63 PB37 in accordance with J-STD-006. Part or Identifying Number (PIN): PIN shall consist of the letter M, the basic number of the specification sheet, a letter from the insert, a numerical code for the termination length, and a letter code for the

23、 shell finish and hardware column. M83513/19- D 01 A P Specification sheet number Insert arrangements (see figure 2) Termination length Shell finish (interface critical) Hardware A = 09 B = 15 01 = .109 02 = .140 A = Pure electrodeposited aluminum N = No hardware or threaded insert P = jackpost atta

24、ch C = 21 03 = .172 C = Cadmium T = threaded insert D = 25 K = Zinc nickel W = jackpost and threaded insert E = 31 N = electroless nickel F = 37 (space applications only) P = Passivated Stainless Steel T = Nickel fluorocarbon polymer Changes from previous issue. The margins of this specification are

25、 marked with vertical lines to indicate where changes from previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document bas

26、ed on the entire content irrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/19D 10 Referenced documents. In addition to MIL-DTL-83513, this document refere

27、nces the following: MIL-DTL-83513/1 ASTM A484/A484M A-A-59551 MIL-DTL-83513/3 ASTM A582/A582M J-STD-006 MIL-M-24519 ASTM D4067 SAE-AMS-2700 ASTM D5138 ASTM D5927 ASTM D5948 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5935-2007-067) NASA -

28、NA DLA - CC Review activities: Army - AT, CR4, MI Navy - AS, CG, MC, SH Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-