DLA DSCC-DWG-07001-2007 CONNECTOR RECEPTACLE ELECTRICAL (POWER TWO-WIRE POLARIZED TWIST-LOCKING).pdf

《DLA DSCC-DWG-07001-2007 CONNECTOR RECEPTACLE ELECTRICAL (POWER TWO-WIRE POLARIZED TWIST-LOCKING).pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-07001-2007 CONNECTOR RECEPTACLE ELECTRICAL (POWER TWO-WIRE POLARIZED TWIST-LOCKING).pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.100 REV PAGE REV REV STATUS OF PAGES PAGE 1 2 3 PREPARED BY PMIC N/A Eric Evans DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 CHECKED BY TITLE Abdonasser M. Abdouni APPROVED BY Lee Surowiec CONNECTOR, RECEPTACL

2、E, ELECTRICAL (POWER, TWO-WIRE, POLARIZED, TWIST-LOCKING) SIZE CAGE CODE 037Z3 DWG. NO. 07001 Original date of drawing 12 June 2007 A REV PAGE 1 OF 3 AMSC N/A 5935-E808-000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3

3、07001 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVPAGE2 Inches mm Inches mm .02 .51 .500 12.70 .025 .64 .532 13.51 .06 1.52 .752 19.10 .062 1.57 .88 22.35 .075 1.91 1.031 26.19 .078 1.98 1.460 37.08 .090 2.29 1.504 38.20 .100 2.54 1.62 41.15 .203 5.16 1.69 42.93 .245 6.22 1.75 44.45

4、 .285 7.24 2.06 52.32 .312 7.92 2.50 63.50 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .xx .03 (0.76 mm) and .xxx .005 (0.13 mm) and 2. 4. The configuration of the external perimeter of the connector body is

5、optional to the extent limited by the dimensions shown on the figure. 5. All current carrying parts shall be electroplated. FIGURE 1. Receptacle. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 07001 DEFENSE SUPPLY CENTER

6、, COLUMBUS COLUMBUS, OH 43218-3990 A REVPAGE3 REQUIREMENTS: This drawing shall meet all of the applicable requirements of W-C-596. Design and construction: See figure 1. Material: Connector body shall be molded plastic or molded rubber. Ratings: Voltage 250 Vac or 250 Vdc. Current 20 amps ac or dc.

7、Voltage drop: 80 mV at 20 amps. Coupling and uncoupling force: Insertion and withdrawal 3 lbs min 15 lbs max. Locking in and unlocking (torque) 2.5 lb in min. Separation force: Applicable. Part or Identifying Number (PIN): The PIN shall be in accordance with the following: 07001-1. QUALIFICATION: Ap

8、proved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed herein have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. DSCC Drawing PIN 1/ Vendor CAGE number Vendor PIN 0

9、7001-1 06VH7 TL200 1/ Parts must be purchased to this DSCC PIN to ensure that all performance requirements and tests are met. Vendor CAGE number Vendor Name and address 06VH7 NEA Electronics, Inc 9204 Deering Avenue Chatsworth, CA 91311 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-