DIN ISO 10230-2016 Cycles - Splined hub and sprocket - Mating dimensions (ISO 10230 1990)《自行车 键槽后轴身和飞轮 配合尺寸(ISO 10230-1990)》.pdf

《DIN ISO 10230-2016 Cycles - Splined hub and sprocket - Mating dimensions (ISO 10230 1990)《自行车 键槽后轴身和飞轮 配合尺寸(ISO 10230-1990)》.pdf》由会员分享，可在线阅读，更多相关《DIN ISO 10230-2016 Cycles - Splined hub and sprocket - Mating dimensions (ISO 10230 1990)《自行车 键槽后轴身和飞轮 配合尺寸(ISO 10230-1990)》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、July 2016 English price group 4No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 43.150!%XLL“2534141www.din.deDIN ISO

2、 10230Cycles Splined hub and sprocket Mating dimensions (ISO 10230:1990),English translation of DIN ISO 10230:2016-07Fahrrder Aufsteckbare Zahnkrnze Anschlussmae (ISO 10230:1990),Englische bersetzung von DIN ISO 10230:2016-07Cycles Pignons et corps dentranement cannels Dimensions dassemblage (ISO 10

3、230:1990),Traduction anglaise de DIN ISO 10230:2016-07www.beuth.deDocument comprises 5 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.07.16 A comma is used as the decimal marker. Start of application The start of application o

4、f this standard is 2016-07-01. Contents Page National foreword . National Annex NA (informative) Bibliography.1 Scope . 4 2 Dimensions and tolerances 4 DIN ISO 10230:2016-07 23 3National foreword This standard includes safety requirements within the meaning of the Produktsicherheitsgesetz (ProdSG) (

5、German Product Safety Act). This document (ISO 10230:1990) has been prepared by Technical Committee ISO/TC 149 “Cycles”. The responsible German body involved in its preparation was DIN-Normenausschuss Sport- und Freizeitgert (DIN Standards Committee Sports Equipment), Working Committee NA 112-06-01

6、AA Fahrrder fr allge-meine und sportliche Benutzung. Attention is drawn to the possibility that some elements of this document may be the subject of patent rights. DIN and/or DKE shall not be held responsible for identifying any or all such patent rights. Where this standard has been identified by t

7、he Ausschuss fr Produktsicherheit (German Committee for Product Safety) and reference to it has been published in the Gemeinsames Ministerialblatt (German Joint Ministerial Gazette) by the Bundesanstalt fr Arbeitsschutz und Arbeitsmedizin (BAuA) (German Federal Institute for Occupational Safety and

8、Health), it is to be presumed that splined hub and sprocket for cycles which comply with this standard fulfil the relevant health and safety requirements. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 1101:1983 DIN EN ISO 1101:1985-03

9、 (current edition DIN EN ISO 1101:2014-04) ISO 2692:1988 DIN ISO 2692:1990-05 (current edition DIN EN ISO 2692:2015-12) National Annex NA (informative) Bibliography DIN EN ISO 1101:1985-03, Geometrical Product Specifications (GPS) Geometrical tolerancing Tolerances of form, orientation, location and run-out (ISO 1101:1983) DIN ISO 2692:1990-05, Technical drawings Geometrical tolerancing Maximum material principle (identical with ISO 2692:1988) DIN ISO 10230:2016-07 3 DIN ISO 10230:2016-07 4 DIN ISO 10230:2016-07 5