DIN EN ISO 6383-1-2016 Plastics - Film and sheeting - Determination of tear resistance - Part 1 Trouser tear method (ISO 6383-1 2015) German version EN ISO 6383-1 2015《塑料 薄膜和薄板 耐撕裂.pdf

《DIN EN ISO 6383-1-2016 Plastics - Film and sheeting - Determination of tear resistance - Part 1 Trouser tear method (ISO 6383-1 2015) German version EN ISO 6383-1 2015《塑料 薄膜和薄板 耐撕裂.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 6383-1-2016 Plastics - Film and sheeting - Determination of tear resistance - Part 1 Trouser tear method (ISO 6383-1 2015) German version EN ISO 6383-1 2015《塑料 薄膜和薄板 耐撕裂.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、May 2016 English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 83.140.10!%SMR“2484247www.din.deDIN E

2、N ISO 6383-1Plastics Film and sheeting Determination of tear resistance Part 1: Trouser tear method (ISO 6383-1:2015);English version EN ISO 6383-1:2015,English translation of DIN EN ISO 6383-1:2016-05Kunststoffe Folien und Bahnen Bestimmung der Reifestigkeit Teil 1: Hosenrei-Verfahren (ISO 6383-1:2

3、015);Englische Fassung EN ISO 6383-1:2015,Englische bersetzung von DIN EN ISO 6383-1:2016-05Plastiques Film et feuille Dtermination de la rsistance au dchirement Partie 1: Mthode de dchirement pantalon (ISO 6383-1:2015);Version anglaise EN ISO 6383-1:2015,Traduction anglaise de DIN EN ISO 6383-1:201

4、6-05SupersedesDIN EN ISO 6383-1:2004-10www.beuth.deDocument comprises 12 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.04.16 DIN EN ISO 6383-1:2016-05 2 A comma is used as the decimal marker. National foreword This document (

5、EN ISO 6383-1:2015) has been prepared by Technical Committee ISO/TC 61 “Plastics” in collaboration with Technical Committee CEN/TC 249 “Plastics” (Secretariat: NBN, Belgium). The responsible German body involved in its preparation was DIN-Normenausschuss Kunststoffe (DIN Standards Committee Plastics

6、), Working Committee NA 054-04-04 AA Kunststoff-Folien und kunststoff-beschichtete Flchengebilde (Kunstleder); allgemeine Eigenschaften. EN ISO 6383 consists of the following parts, under the general title Plastics Film and sheeting Determination of tear resistance: Part 1: Trouser tear method Part

7、2: Elmendorf method The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 291 DIN EN ISO 291 ISO 527-3 DIN EN ISO 527-3 Amendments This standard differs from DIN EN ISO 6383-1:2004-10 as follows: a) normative references have been updated; b)

8、the standard has been editorially revised. Previous editions DIN EN ISO 6383-1: 2004-10 National Annex NA (informative) Bibliography DIN EN ISO 291, Plastics Standard atmospheres for conditioning and testing DIN EN ISO 527-3, Plastics Determination of tensile properties Part 3: Test conditions for f

9、ilms and sheets EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 6383-1 December 2015 ICS 83.140.10 Supersedes EN ISO 6383-1:2004English Version Plastics Film and sheeting Determination of tear resistance Part 1: Trouser tear method (ISO 6383-1:2015) Plastiques Film et feuille Dtermination d

10、e la rsistance au dchirement Partie 1: Mthode de dchirement pantalon (ISO 6383-1:2015) Kunststoffe Folien und Bahnen Bestimmung der Reifestigkeit Teil 1: Hosenrei-Verfahren (ISO 6383-1:2015) This European Standard was approved by CEN on 31 October 2015. CEN members are bound to comply with the CEN/C

11、ENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centr

12、e or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the

13、official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherla

14、nds, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights

15、 of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 6383-1:2015 EEN ISO 6383-1:2015 (E) 2 DIN EN ISO 6383-1:2016-05 Contents Page European foreword . 3 Foreword 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 5 4 Significance 5 5

16、Principle . 6 6 Apparatus . 6 7 Test specimens . 6 8 Number of test specimens 7 9 Speed of testing 7 10 Conditioning 7 11 Procedure. 7 12 Expression of results 7 13 Test report . 8 EN ISO 6383-1:2015 (E) 3 European foreword This document (EN ISO 6383-1:2015) has been prepared by Technical Committee

17、ISO/TC 61 “Plastics” in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2016, and conflic

18、ting national standards shall be withdrawn at the latest by June 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document s

19、upersedes EN ISO 6383-1:2004. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Repu

20、blic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 6383-1:2015 has been a

21、pproved by CEN as EN ISO 6383-1:2015 without any modification. DIN EN ISO 6383-1:2016-05 ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out

22、through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO coll

23、aborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approv

24、al criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the sub

25、ject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trad

26、e name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Tec

27、hnical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 11, Products.This second edition cancels and replaces the first edition (ISO 6383-1:1983), of which it constitutes a minor re

28、vision.ISO 6383 consists of the following parts, under the general title Plastics Film and sheeting Determination of tear resistance: Part 1: Trouser tear method Part 2: Elmendorf methodEN ISO 6383-1:2015 (E) 4DIN EN ISO 6383-1:2016-05 1 ScopeThis part of ISO 6383 specifies a method of determining t

29、he tear resistance of plastic film or sheet less than 1 mm thick, in the form of standard trouser-shaped test specimens, tested under defined conditions of pre-treatment, temperature, humidity, and speed of testing.The method is applicable to film and sheeting of both flexible and rigid materials, p

30、rovided that the material is not so rigid that brittle fracture occurs during the test, or so deformable, in an irreversible way, that the energy used in the deformation of the specimen legs is significant (i.e. is not negligible) with respect to the energy used in tearing.The method may not be suit

31、able for determining the tear properties of cellular sheet and film.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references,

32、 the latest edition of the referenced document (including any amendments) applies.ISO 291, Plastics Standard atmospheres for conditioning and testingISO 5273, Plastics Determination of tensile properties Part 3: Test conditions for films and sheetsISO 4591, Plastics Film and sheeting Determination o

33、f average thickness of a sample, and average thickness and yield of a roll, by gravimetric techniques (gravimetric thickness)ISO 4593, Plastics Film and sheeting Determination of thickness by mechanical scanning3 Terms and definitionsFor the purpose of this document, the following terms and definiti

34、ons apply.3.1tearing forceaverage force required to propagate a tear at a constant tearing speed across a test specimen conforming to Figure 13.2tear resistancetearing force divided by the specimen thickness4 Significance4.1 This method may provide data for quality control, acceptance, or rejection

35、in accordance with the terms of specifications and for research and development.EN ISO 6383-1:2015 (E) 5DIN EN ISO 6383-1:2016-05 4.2 Tear properties may vary with specimen preparation, speed of testing, and environment of testing. Consequently, when precise comparative results are required, these f

36、actors shall be carefully controlled.It is possible, in principle, to compare the tear resistance (3.2) of specimens of different materials, provided that their thicknesses do not differ by more than 10 %. However, caution is necessary in interpreting such results, since the tearing energy can vary

37、considerably with speed of testing for different materials.5 PrincipleA rectangular test specimen having a longitudinal slit extending over half its length is subjected to a tensile test on the “trouser legs” formed by the slit. The average force required to tear the specimen completely along its le

38、ngth is used to calculate the tear resistance of the material under test (see Figure 1).6 Apparatus6.1 Tensile testing machine (not pendulum type), similar to that specified in ISO 527-3, having the following characteristics.6.1.1 It shall be power driven and capable of maintaining the appropriate r

39、ate of grip separation specified in Clause 9. It is essential that the load measuring device is equipped with an autographic recording device to record the load applied to the specimen as a function of elapsed time from the start of the test.6.1.2 The grips shall be equipped with chucks designed to

40、securely hold the legs of the test specimen without slip. The chucks shall be wider than the width of the test specimen and, in order that they remain parallel to each other during a test, they shall not be mounted on swivel joints.6.2 Suitable equipment for measuring the thickness of specimens by t

41、he method described in ISO 4593. For embossed film or sheeting, the apparatus specified in ISO 4591 shall be used.7 Test specimens7.1 Test specimens shall have the shape and dimensions shown in Figure 1. The length of the slit in the centre of the specimen shall be 75 mm 1 mm.7.2 The test specimens

42、shall be cut so that the edges are smooth and free from notches. Examination with a low-power microscope is recommended to check freedom from nicks. It is important to pay particular attention to the tip of the slit in the centre of the specimen.7.3 The properties of certain types of film and sheeti

43、ng materials may vary with direction in the plane of the film (anisotropy). In such cases, it is essential to prepare two groups of test specimens with their major axes respectively parallel and perpendicular to the direction of some feature of the film or sheeting which is either visible or inferre

44、d from knowledge of the method of its manufacture.The direction of testing is defined as the direction of the long axis of the test specimen.With some types of film, different tear resistance results may be obtained for any direction of testing (for example, machine direction or transverse direction

45、) depending, for example, in the case of machine direction test specimens, on whether the tear propagation is in the direction of processing or against the process direction (see Figure 2). When this is known to occur, two groups of test specimens shall be cut in the direction of testing and slit so

46、 that results can be obtained for the two possible directions of tear propagation.EN ISO 6383-1:2015 (E) 6DIN EN ISO 6383-1:2016-05 8 Number of test specimens8.1 A minimum of five test specimens shall be tested in each of the required directions of testing.8.2 Specimens which show a tear out of line

47、 to the extent that the tear reaches one of the edges of the test specimen shall be discarded and further specimens tested (see 11.3).9 Speed of testingThe speed of testing shall be one of the following: 200 mm/min 10 %; 250 mm/min 10 %.NOTE At present time, both speeds of testing are common through

48、out the world. For the time being, both are being allowed for the purpose of this part of ISO 6383. Subsequent revisions of this part of ISO 6383 might only incorporate the testing speed of 200 mm/min.10 ConditioningUnless otherwise specified, test specimens shall be conditioned and tested in accord

49、ance with ISO 291, using atmosphere 23 C/50 %, except that when a material is known not to be sensitive to humidity, atmosphere 23 C may be used.11 Procedure11.1 Measure the thickness of the material under test using measuring devices complying with the requirements of ISO 4593. If, however, the film is very thin or if it is embossed, determine the thickness by the method of ISO 4591.11.1.1 When using measuring d