DIN EN ISO 18613-2015 Pallets for materials handling - Repair of flat wooden pallets (ISO 18613 2014) German version EN ISO 18613 2014《材料搬运用托盘 木制平托盘的修理 (ISO 18613-2014) 德文版本EN ISO .pdf

《DIN EN ISO 18613-2015 Pallets for materials handling - Repair of flat wooden pallets (ISO 18613 2014) German version EN ISO 18613 2014《材料搬运用托盘 木制平托盘的修理 (ISO 18613-2014) 德文版本EN ISO .pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 18613-2015 Pallets for materials handling - Repair of flat wooden pallets (ISO 18613 2014) German version EN ISO 18613 2014《材料搬运用托盘 木制平托盘的修理 (ISO 18613-2014) 德文版本EN ISO .pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、March 2015 Translation by DIN-Sprachendienst.English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS

2、55.180.20!%A*u“2300782www.din.deDDIN EN ISO 18613Pallets for materials handling Repair of flat wooden pallets (ISO 18613:2014);English version EN ISO 18613:2014,English translation of DIN EN ISO 18613:2015-03Paletten fr die Handhabung von Gtern Reparatur von Flachpaletten aus Holz (ISO 18613:2014);E

3、nglische Fassung EN ISO 18613:2014,Englische bersetzung von DIN EN ISO 18613:2015-03Palettes pour la manutention et le transport des marchandises Rparation des palettes plates en bois (ISO 18613:2014);Version anglaise EN ISO 18613:2014,Traduction anglaise de DIN EN ISO 18613:2015-03SupersedesDIN EN

4、ISO 18613:2003-08www.beuth.deDocument comprises 22 pagesIn case of doubt, the German-language original shall be considered authoritative.02.15 DIN EN ISO 18613:2015-03 2 A comma is used as the decimal marker. National foreword This document (EN ISO 18613:2014) has been prepared by Technical Committe

5、e ISO/TC 51 “Pallets for unit load method of materials handling” in collaboration with Technical Committee CEN/TC 261 “Packaging” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the DIN-Normenausschuss Verpackungswesen (Packaging Standards Committee), Workin

6、g Committee NA 115-03-07 AA Paletten. The European Standards referred to in this document have been published as DIN EN or DIN EN ISO Standards with the same number. The DIN Standard corresponding to the International Standard referred to in this standard is as follows: ISO 445 DIN EN ISO 445 Amendm

7、ents This standard differs from DIN EN ISO 18613:2003-08 as follows: a) ISPM No. 15 6 and UIC 435-4 7 have been added to the Bibliography; b) Subclause B.2 has been extended to include item i): “Essential markings stipulated in a specification are missing or illegible”; c) Subclause C.1 has been mod

8、ified: “3) splits on top or bottom deck boards of more than 1/2 of the length or width of the board”; d) Table F.1, columns “Type of fault” and “Action”, last line, have been supplemented: loose joints, renailing; e) the standard has been editorially revised. Previous editions DIN EN ISO 18613: 2003

9、-08 National Annex NA (informative) Bibliography DIN EN ISO 445, Pallets for materials handling Vocabulary EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 18613 November 2014 ICS 55.180.20 Supersedes EN ISO 18613:2003 English Version Pallets for materials handling Repair of flat wooden pall

10、ets (ISO 18613:2014) Palettes pour la manutention et le transport des marchandises Rparation des palettes plates en bois (ISO 18613:2014) Paletten fr die Handhabung von Gtern Reparatur von Flachpaletten aus Holz (ISO 18613:2014) This European Standard was approved by CEN on 25 August 2014. CEN membe

11、rs are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applicatio

12、n to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Manageme

13、nt Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, L

14、ithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17

15、, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 18613:2014 E Contents PageForeword . 3Introduction 41 Scope . 52 Normative references 43 Terms and definitions . 44 Defects and damage criteria . 64.1 Overr

16、iding criterion 4.2 Nail joint strength .4.3 Inspection 4.4 General conditions identifying an unacceptable pallet 5 Repair . 65.1 General . 65.2 Repair of pallets of known specification . 75.3 Repair of pallets of unknown specification 75.4 Marking . 95.5 Final inspection of repaired pallets. 96 Rec

17、ycling - disposal 9Annex A (informative) Defects and damage which make a 4-way block pallet unacceptable for use 10Annex B (informative) Defects and damage which make a perimeter base pallet unacceptable for use 11Annex C (informative) Defects and damage which make a 2-way stringer (bearer) pallet u

18、nacceptable for use 13Annex D (informative) Defects or damage which make a partial 4-way pallet unacceptable for use 14Annex E (normative) Metal plates for repairing of notched stringers (bearers) .16Annex F (informative) Action needed for the repair of pallets of unknown specification .18Annex G (i

19、nformative) Special accuracy and tolerance for repaired pallets (e.g. for use in certain automatic handling systems) 19Bibliography 202DIN EN ISO 18613:2015-03 EN ISO 18613:2014 (E) 6666Foreword This document (EN ISO 18613:2014) has been prepared by Technical Committee ISO/TC 51 “Pallets for unit lo

20、ad method of materials handling“ in collaboration with Technical Committee CEN/TC 261 “Packaging” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 201

21、5, and conflicting national standards shall be withdrawn at the latest by May 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. Th

22、is document supersedes EN ISO 18613:2003. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Y

23、ugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 18613:2014

24、 has been approved by CEN as EN ISO 18613:2014 without any modification. 3DIN EN ISO 18613:2015-03 EN ISO 18613:2014 (E) IntroductionMandatory requirements for recycling of packaging materials has led to an expansion of reuse, repair and recycling of wooden pallets. This International Standard is in

25、tended to assist this process, in that, through its implementation, the safety and longevity of repaired pallets will be maximised. This International Standard also refers particularly to new pallet standards and prescriptive pallet specifications in wide use.There is no requirement in this Internat

26、ional Standard for pallet repairers to undertake tests, since, if guidance given in this International Standard is followed and systematic repair and inspection systems are used, then a successful repair is assumed to follow.There are four related International Standards: ISO 15629, Pallets for mate

27、rials handling Quality of fasteners for assembly of new and repair of used, flat wooden pallets ISO 18333, Pallets for materials handling Quality of new wooden components for flat pallets ISO 18334, Pallets for materials handling Quality of assembly of new wooden pallets ISO 18613, Pallets for mater

28、ials handling Repair of flat wooden pallets4DIN EN ISO 18613:2015-03 EN ISO 18613:2014 (E) 1 ScopeThis International Standard specifies the maximum defects and damage allowed before a flat wooden pallet shall be repaired, and defines the minimum repair criteria that shall be used.This International

29、Standard is applicable to wooden flat pallets repaired with wood based components.NOTE The maximum allowed defects and damage for pallets are described in this International Standard and the Annexes A to D show examples of defects and damage which make the widely used pallets unacceptable for use. F

30、or other pallet types similar criteria should be set up. The repair criteria for pool and rental pallets are controlled by their respective controlling operators/owners, and may be subject to a licence.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in

31、this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 445, Pallets for materials handling VocabularyISO 15629, Pallets for materials h

32、andling Quality of fasteners for assembly of new and repair of used, flat, wooden palletsEN 1087-1:1994, Particleboards Determination of moisture resistance Boil test3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 445 (some of which are repeated below

33、 for convenience) and the following apply.3.1boardtop deck board, bottom deck board, or stringer board3.2deckboardindividual member of a top or bottom deck3.3bottom deck boardindividual member of bottom deck3.4stringerboardhorizontal member linking the blocks and deckboards3.5stringer or bearerconti

34、nuous longitudinal member underneath the top deck or between the top and bottom decks, which provides space for the entry of fork-lift forks and pallet-truck fingers5DIN EN ISO 18613:2015-03 EN ISO 18613:2014 (E) 4 Defects and damage criteria4.1 Overriding criterionThe overriding criterion for an un

35、acceptable pallet is if its condition is such that it cannot be regarded as safe and that handling the pallet might be dangerous for persons or goods (as illustrated in Annexes A to D).4.2 Nail joint strengthNail joint strength is particularly important for the performance of pallets.4.3 InspectionI

36、nspection of a pallet shall take place before any handling, whether loaded or empty.4.4 General conditions identifying an unacceptable palletThe general conditions which make a pallet unacceptable for use are as follows.a) One deckboard missing or broken, either obliquely or across.b) Either one blo

37、ck, stringer (bearer) or stringerboard missing or broken.c) Missing wood on deckboards to such an extent that on one deckboard, two or more nail shanks are visible, or on more than two deckboards, one or more nail shanks are visible, or missing wood of more than 1/4 of the width of the board for 1/4

38、 length. Missing wood on a deckboard between the blocks of more than 1/4 of the width of the deckboard.d) Splits on deckboards of more than 1/2 of the width or the length of the deckboard, which cannot be securely nailed.e) Wings on pallets may only have missing wood from inner deckboard ends for a

39、maximum of 1/3 of projecting wing length.f) Missing wood on blocks, stringers (bearers) or stringerboards, if more than one nail shank is visible at any one joint.g) Depending on use, dirty or contaminated pallet. If any doubt exists as to the nature of the contamination, care shall be taken in its

40、identification and subsequent disposal.h) Older pallets with a combination of minor damage or loose joints and with a poor appearance may have a combination of issues and be unacceptable when viewed as a whole.i) Pallets with bad workmanship. Pallets with materials or components that have been previ

41、ously incorrectly applied.j) Components affected by decay which could affect their mechanical properties.k) Full width splits of any length in stringer (bearer) notches.NOTE Attention is also drawn to publication UIC-Leaflet 4354 (2010) Repair of EUR flat pallets and EUR box pallets.5 Repair5.1 Gene

42、ralComponents with unacceptable defects or damage shall be removed and replaced by new or re-used components of one piece.6DIN EN ISO 18613:2015-03 EN ISO 18613:2014 (E) 5.1.1 Blocks of particleboardIf blocks of particleboard are used they shall conform to EN 1087-1. The density of the particle boar

43、d shall be more than 580 kg per cubic metre.5.1.2 Bottom deckboardsBottom deckboards and the corners of the pallet shall be chamfered, if required.5.1.3 Nail headsNail heads shall be countersunk so that the top of the head of the nail cannot be snagged above the surface.5.2 Repair of pallets of know

44、n specificationReplacement components shall be from new or re-used materials. They shall be in accordance with the relevant specifications of the pallet and its repair requirements in the relevant standards. Re-used components shall conform to all the requirements of the new pallet component specifi

45、cations. No missing wood or splits are allowed in these re-used components. The nails used and the final assembled pallet shall meet the requirements of the specifications for that pallet.NOTE Repair requirements may differ from the new pallet specification. Details as agreed by contract.Pallets whi

46、ch are unacceptable for use, shall be repaired or disposed of, and marking requirements met as defined in 5.4.5.3 Repair of pallets of unknown specificationIf the specification is not known or no specification exists, the replacement components shall have the same dimensions and quality as the remov

47、ed components. Replacement components may be from new or re-used materials. Components shall meet the conditions given in 5.3.3. Too many nail holes may weaken the component.5.3.1 Dimensional tolerancesThe general maximum permitted tolerances from basic dimensions for pallets of unknown specificatio

48、ns shall be as in Table 1.7DIN EN ISO 18613:2015-03 EN ISO 18613:2014 (E) Table 1 General maximum permitted tolerances from basic dimensions for pallets of unknown specificationsComponent ToleranceLength + 8 / 8 mmWidth + 8 / 8 mmOverall height + 10/ 10 mmDiagonal difference + 10/ 10 mmFlatness Within 10 mmBlock twist No overhangTop gaps Max 65 mmLead board position from edge + 0 / 5 mmInner deckboard position from centre line + 2,5 / 2,5 mmStringerboard position from centre line + 2,5 / 2,5 mmStri