DIN EN ISO 17130-2013 Leather - Physical and mechanical tests - Determination of dimensional change (ISO 17130 2013) German version EN ISO 17130 2013《皮革 物理和机械试验 尺寸变化测定(ISO 17130-20.pdf

《DIN EN ISO 17130-2013 Leather - Physical and mechanical tests - Determination of dimensional change (ISO 17130 2013) German version EN ISO 17130 2013《皮革 物理和机械试验 尺寸变化测定(ISO 17130-20.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 17130-2013 Leather - Physical and mechanical tests - Determination of dimensional change (ISO 17130 2013) German version EN ISO 17130 2013《皮革 物理和机械试验 尺寸变化测定(ISO 17130-20.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、August 2013 Translation by DIN-Sprachendienst.English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS

2、59.140.30!%(=D“2052633www.din.deDDIN EN ISO 17130Leather Physical and mechanical tests Determination of dimensional change (ISO 17130:2013);English version EN ISO 17130:2013,English translation of DIN EN ISO 17130:2013-08Leder Physikalische und mechanische Prfungen Bestimmung der Mahaltigkeit (ISO 1

3、7130:2013);Englische Fassung EN ISO 17130:2013,Englische bersetzung von DIN EN ISO 17130:2013-08Cuir Essais physiques et mcaniques Dtermination des variations dimensionnelles (ISO 17130:2013);Version anglaise EN ISO 17130:2013,Traduction anglaise de DIN EN ISO 17130:2013-08www.beuth.deDocument compr

4、ises pagesIn case of doubt, the German-language original shall be considered authoritative.908.13 DIN EN ISO 17130:2013-08 2 A comma is used as the decimal marker. National foreword This document (EN ISO 17130:2013) has been prepared by Technical Committee CEN/TC 289 “Leather” (Secretariat: UNI, Ita

5、ly) in collaboration with the International Union of Leather Technologists and Chemists Societies (IULTCS). The responsible German body involved in its preparation was the Normenausschuss Materialprfung (Materials Testing Standards Committee), Working Committee NA 062-05-51 AA Anforderungen und phys

6、ikalische Prfverfahren fr Leder und seine Ausgangsprodukte. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 105-B06 DIN EN ISO 105-B06 ISO 2418 DIN EN ISO 2418 ISO 2419 DIN EN ISO 2419 ISO 17228 DIN EN ISO 17228 National Annex NA (infor

7、mative) Bibliography DIN EN ISO 105-B06, Textiles Tests for colour fastness Part B06: Colour fastness and ageing to artificial light at high temperatures: Xenon arc fading lamp test DIN EN ISO 2418, Leather Chemical, physical and mechanical and fastness tests Sampling location DIN EN ISO 2419, Leath

8、er Physical and mechanical tests Sample preparation and conditioning DIN EN ISO 17228, Leather Tests for colour fastness Change in colour with accelerated ageing EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 17130 May 2013 ICS 59.140.30 English Version Leather - Physical and mechanical te

9、sts - Determination of dimensional change (ISO 17130:2013) Cuir - Essais physiques et mcaniques - Dtermination des variations dimensionnelles (ISO 17130:2013) Leder - Physikalische und mechanische Prfung - Bestimmung der Mahaltigkeit (ISO 17130:2013) This European Standard was approved by CEN on 25

10、April 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be o

11、btained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the

12、 CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Irel

13、and, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue

14、Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 17130:2013: EContents DIN EN ISO 17130:2013-08 EN ISO 17130:2013 (E) 2 Page Foreword 3 1 Scope 4 2 Normative references 4 3 Principle 4 4 Apparatus

15、 and materials . 4 5 Sampling and sample preparation . 4 6 Procedure . 5 7 Expression of results 6 8 Test report 7 Foreword This document (EN ISO 17130:2013) has been prepared by IULTCS International Union of Leather Technologists and Chemists Societies” in collaboration with Technical Committee CEN

16、/TC 289 “Leather” the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2013, and conflicting national standards shall be withdrawn at the latest by Nov

17、ember 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards

18、organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembo

19、urg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 17130:2013 has been approved by CEN as EN ISO 17130:2013 without any modification. DIN EN ISO 17130:2013-08 EN ISO 17130:2013

20、(E) 3 “1 ScopeThis International Standard specifies a method of determining the dimensional change (shrinkage) of leathers caused by ageing. It is applicable to all leathers.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indisp

21、ensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 105-B06, Textiles Tests for colour fastness Part B06: Colour fastness and ageing to artificial light at high

22、 temperatures: Xenon arc fading lamp testISO 2418, Leather Chemical, physical and mechanical and fastness tests Sampling locationISO 2419, Leather Physical and mechanical tests Sample preparation and conditioningISO 17228, Leather Tests for colour fastness Change in colour with accelerated ageing3 P

23、rincipleA conditioned test piece is aged using the conditions defined in ISO 17228. The shrinkage is determined after reconditioning.4 Apparatus and materials4.1 Oven, as specified in ISO 17228.4.2 Climate chamber, as specified in ISO 17228.4.3 Vernier calliper, reading to 0,1 mm.4.4 Support, glass

24、plate covered with a polyester nonwoven fabric (as specified in ISO 105-B06).NOTE The glass plate support keeps the test piece flat and the polyester fabric stops the test piece from sticking to the glass.4.5 Press knife, square, as specified in ISO 2419 with inner walls measuring 150 mm 1 mm.4.6 In

25、delible marker.5 Sampling and sample preparation5.1 Sample in accordance with ISO 2418. Cut at least two test pieces (150 150) mm for each of the ageing conditions required, by applying the press knife (4.5) to the grain surface, if distinguishable.DIN EN ISO 17130:2013-08 EN ISO 17130:2013 (E) 4 NO

26、TE For some applications, it can be necessary to use larger test pieces e.g. (300 300) mm to enhance the accuracy, especially in the case of low shrinkage.5.2 Using an indelible marker (4.6), mark the lines and measurement reference points A, B, C and D on the test pieces. Mark a square with a lengt

27、h of (100 1) mm (Figure 1).Dimensions in millimetres 1 mmFigure 1 Location of lines and measurement reference points on a test pieceIf test pieces with another dimension, e.g. (300 300) mm, are used, a square should be marked with a distance to each edge of (25 1) mm.5.3 Condition the test pieces in

28、 accordance with ISO 2419 for at least 48 h.6 Procedure6.1 Measure the distances AB, CD, AC and BD on each test piece using the vernier calliper (4.3).6.2 Preheat the oven (4.1) to the test temperature or adjust the climate chamber (4.2) to the starting conditions. Place the test pieces with the gra

29、in side, top side or coated side downward on the support (4.4) in the centre of the oven or climate chamber.To allow a fast exchange of humidity, it is necessary to place the leather in such a way that an intensive contact of the air in the oven or climate chamber with the flesh side of the leather

30、is guaranteed.6.3 Age the test pieces as described in ISO 17228.6.4 If required, measure the distances between the measurement points following the description in 6.1 immediately after ageing (not later than 5 min). In this case, report that the measurement was made immediately.DIN EN ISO 17130:2013

31、-08 EN ISO 17130:2013 (E) 5 6.5 Recondition the test pieces for at least 48 h in accordance with ISO 2419.6.6 Measure the distances between the measurement points following the description in 6.1.6.7 Note any visual changes of the test piece, such as distortion and any changes in flexibility and sof

32、tness manually.7 Expression of results7.1 The shrinkage may be expressed as linear shrinkage (see 7.2) or loss of area (area shrinkage)(see 7.3).7.2 The linear shrinkage is calculated using Formulae (1), (2) and (3).Calculate the mean of original length, L1, bounded by the points ABCD on the test pi

33、ece, as follows:Lacbd111114=+ () (1)where a1, b1, c1, and d1are the values of the dimensions AB, BD, CD, AC respectively (see Figure 1), measured before the test.Calculate the mean of length after the test, L2, bounded by the points ABCD on the test piece, as follows:Lacbd222224=+ () (2)where a2, b2

34、, c2and d2are the values of the dimensions AB, BD, CD, AC respectively (see Figure 1), measured after the test.Calculate the percentage linear shrinkage SLusing the Formula (3):SLLLL=121100 (3)whereL1is the mean of original length, calculated from Formula (1);L2is the mean of length after the test,

35、calculated from Formula (2).7.3 For the calculation of loss of area (area shrinkage) SAproceed as follows:Calculate the original area, A1, bounded by the points ABCD on the test piece, as follows:Aacbd1111122=+(4)where a1, b1, c1and d1are the values of the dimensions AB, BD, CD, AC respectively (see

36、 Figure 1), measured before the test.Calculate the area after the test, A2, bounded by the points ABCD on the test piece, as follows:Aacbd222 22=+(5)where a2, b2, c2and d2are the values of the dimensions AB, BD, CD, AC respectively (see Figure 1), measured after the test.DIN EN ISO 17130:2013-08 EN

37、ISO 17130:2013 (E) 6 Calculate the percentage loss of area (area shrinkage) SA, using Formula (6):SAAAA=121100 (6)whereA1is the original area, calculated from Formula (4);A2is the area after the test, calculated from Formula (5).8 Test reportThe test report shall include the following:a) reference t

38、o this International Standard, i.e. ISO 17130;b) full details for identification of the sample and any deviation from ISO 2418 with respect to sampling;c) the test conditions used for ageing;d) mean value of the percentage linear shrinkage SLas calculated in 7.2 or mean value of percentage loss in a

39、rea SA(area shrinkage) as calculated in 7.3 to the nearest 0,1 %;e) details of any visual changes or changes in flexibility and softness;f) the standard atmosphere used for conditioning and testing as given in ISO 2419;g) any deviations from the method specified in this International Standard.DIN EN ISO 17130:2013-08 EN ISO 17130:2013 (E) 7