DIN EN 15570-2008 Hardware for furniture - Strength and durability of hinges and their components - Hinges pivoting on a vertical axis German version EN 15570 2008《家具用五金件 铰链及其部件的强度.pdf

《DIN EN 15570-2008 Hardware for furniture - Strength and durability of hinges and their components - Hinges pivoting on a vertical axis German version EN 15570 2008《家具用五金件 铰链及其部件的强度.pdf》由会员分享，可在线阅读，更多相关《DIN EN 15570-2008 Hardware for furniture - Strength and durability of hinges and their components - Hinges pivoting on a vertical axis German version EN 15570 2008《家具用五金件 铰链及其部件的强度.pdf（25页珍藏版）》请在麦多课文档分享上搜索。

1、August 2008DEUTSCHE NORM English price group 12No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 97.140!$Q4“1465917www.d

2、in.deDDIN EN 15570Hardware for furniture Strength and durability of hinges and their components Hinges pivoting on a vertical axisEnglish version of DIN EN 15570:2008-08Mbelbeschlge Festigkeit und Dauerhaltbarkeit von Scharnieren und deren Komponenten Scharniere mit vertikaler DrehachseEnglische Fas

3、sung DIN EN 15570:2008-08SupersedesDIN 68857:2004-06www.beuth.deDocument comprises 25 pagesDIN EN 15570:2008-08 2 National foreword This standard has been prepared by Technical Committee CEN/TC 207 “Furniture”, (Secretariat:UNI, Italy). The responsible German body involved in its preparation was the

4、 Normenausschuss Holzwirtschaft und Mbel (Timber and Furniture Standards Committee), Technical Committee NA 042-05-06 AA Mbelschlsser, Beschlge und Bauteile Spiegelausschuss zu CEN/TC 207/WG 8. Amendments This standard differs from DIN 68857:2004-06 as follows: a) It has been updated to take account

5、 of market requirements. b) It is geared towards international standardization. c) It has been revised in form and substance. Previous editions DIN 68857: 1981-07, 1986-05, 2004-06 EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15570May 2008ICS 91.190English VersionHardware for furniture - Streng

6、th and durability of hinges andtheir components - Hinges pivoting on a vertical axisQuincaillerie dameublement - Rsistance mcanique etendurance des charnires et de leurs composants -Charnires pivotant sur un axe verticalMbelbeschlge - Festigkeit und Dauerhaltbarkeit vonScharnieren und deren Komponen

7、ten - Scharniere mitvertikaler DrehachseThis European Standard was approved by CEN on 11 April 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-t

8、o-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder

9、the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hunga

10、ry, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue

11、 de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15570:2008: E2 Contents Page Foreword3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 4 General test conditions.6 4.

12、1 Preliminary preparation 6 4.2 Test equipment 6 4.3 Application of forces .6 4.4 Tolerances 6 4.5 Sequence of testing.7 4.6 Inspection and assessment of results 7 5 Test apparatus .7 5.1 Masses 7 5.2 Test frame.7 5.3 Particle board properties 9 6 Test procedures and requirements9 6.1 General9 6.2 O

13、verload tests9 6.2.1 Vertical static overload .9 6.2.2 Horizontal static overload.10 6.3 Functional tests .11 6.3.1 General11 6.3.2 Operating forces 11 6.3.3 1stvertical static load test.13 6.3.4 1sthorizontal static load13 6.3.5 Slam shut13 6.3.6 Determination of reference point for the door saggin

14、g.14 6.3.7 Durability 15 6.3.8 Deflection (sagging) test.16 6.3.9 2ndvertical static load17 6.3.10 2ndhorizontal static load .17 6.4 Corrosion resistance.17 7 Test report 17 Annex A (normative) Product information system 19 A.1 General19 A.2 Field of application 19 A.3 The mass and size of the door

15、.19 A.4 Adjustment systems and spring and damper mechanisms19 A.5 Corrosion test 19 Annex B (normative) Test parameters 20 Bibliography 23 EN 15570:2008 (E) DIN EN 15570:2008-08 EN 15570:2008 (E) 3 Foreword This document (EN 15570:2008) has been prepared by Technical Committee CEN/TC 207 “Furniture”

16、, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2008, and conflicting national standards shall be withdrawn at the latest by November 2008. Atte

17、ntion is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of

18、 the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slov

19、akia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN 15570:2008-08 EN 15570:2008 (E) 4 Introduction The aim of this European Standard is to provide furniture manufacturers, designers and developers with comparable information regarding the performance of all types of hinges pivo

20、ting on a vertical axis and their components. DIN EN 15570:2008-08 EN 15570:2008 (E) 5 1 Scope This European Standard specifies test methods and requirements for the strength and durability of all types of hinges pivoting on a vertical axis and their components for all fields of application. The tes

21、ts consist of the application of loads, forces and velocities simulating normal functional use, as well as misuse, that might reasonably be expected to occur. With the exception of the corrosion test in Clause 6.4, the tests are designed to evaluate properties without regard to materials, design/con

22、struction or manufacturing processes. The strength and durability tests only relate to the hinges and the parts used for the attachment, e.g. mounting plates and screws. The strength and durability tests are carried out in a test frame with specified properties. The test results can only be used as

23、a guide to the performance of a piece of furniture. The test results are only valid for the hinges tested. These results may be used to represent the performance of production models provided that the tested model is representative of the production model. With the exception of corrosion, ageing and

24、 the influence of heat and humidity are not included. Annex A (normative): Requirements for product information. Annex B (normative): Loads and cycles. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edi

25、tion cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 320:1993, Fibreboards - Determination of resistance to axial withdrawal of screws EN 323:1993, Wood-based panels - Determination of density EN ISO 6270-2, Paints and varni

26、shes - Determination of resistance to humidity - Part 2: Procedure for exposing test specimens in condensation-water atmospheres (ISO 6270-2:2005) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 catch device device that keeps or pulls a door

27、in place, but does not require a second action in order to release it, e.g. a magnetic catch or a self-closing or self-opening mechanism 3.2 damper mechanism which stops the movement of a door gently DIN EN 15570:2008-08 EN 15570:2008 (E) 6 4 General test conditions 4.1 Preliminary preparation The h

28、inges shall be assembled/mounted/adjusted according to the instructions supplied with it. If mounting, assembly or adjustment instructions are not supplied, the most adverse configuration shall be used and the mounting or assembly method shall be recorded in the test report. Fittings shall be tighte

29、ned before testing and shall not be re-tightened unless specifically required in the manufacturers instructions. If the configuration must be changed to produce the worst-case conditions, this shall be recorded in the test report. The tests shall be carried out in indoor ambient conditions at a temp

30、erature between 15 C and 25 C. If during a test the temperature is outside of the range of 15 Cto 25 C, the maximum and/or minimum temperature shall be recorded in the test report. Hinges which include structural hardware parts made of hygroscopic plastic materials, e.g. polyamide, shall be conditio

31、ned at (23 5) C and at a relative humidity of (50 5) % for 7 days before testing. NOTE For accelerating the conditioning process, EN ISO 1110:1997 1 may be used. In the case of designs not addressed in the test procedures, the tests shall be carried out as far as possible as described, and deviation

32、s from the test procedure recorded in the test report. Before beginning testing, visually inspect the hinges and components thoroughly. Record any defects to eliminate any assumption that they have been caused by the tests. Carry out measurements if specified. 4.2 Test equipment Unless otherwise spe

33、cified, the tests may be applied by any suitable device because results are not dependent upon the apparatus. The equipment shall not inhibit deflection of the test door, i.e. it shall be able to move so that it will allow the deflection of the test door during testing. 4.3 Application of forces The

34、 forces in the static load tests shall be applied sufficiently slowly to ensure that negligible dynamic force is applied. Unless otherwise specified, each force shall be maintained for not less than 10 s and not more than 15 s. The forces in durability tests shall be applied at a rate to ensure that

35、 excessive heating does not occur. The forces may be replaced by masses. The relation 10 N = 1 kg shall be used for this purpose. 4.4 Tolerances Unless otherwise stated, the following tolerances are applicable: Forces: 5 % of the nominal force; Velocities: 5 % of the nominal velocity; Masses: 1 % of

36、 the nominal mass; Dimensions: 1 mm of the nominal dimension; DIN EN 15570:2008-08 EN 15570:2008 (E) 7 Angles: 2oof the nominal angle. The accuracy for the positioning of forces shall be 5 mm. 4.5 Sequence of testing The tests shall be carried out in the same sequence as the clauses are numbered in

37、this standard. If the clause sequence is not followed, the sequence shall be recorded in the test report. 4.6 Inspection and assessment of results Before and after the completion of each test, carry out the inspection as specified, after using adjustment devices, if available. Record any changes tha

38、t have taken place since the initial inspection. The inspection shall include at least the following: a) fracture of any component or joint; b) loosening of any joint intended to be rigid, which can be demonstrated by hand pressure; c) deformation or wear of any part or component such that its funct

39、ioning is impaired; d) loosening of any means of fixing components; e) any impaired function of a component or part. 5 Test apparatus 5.1 Masses Masses shall be designed so that they do not reinforce the structure or re-distribute the stresses. 5.2 Test frame The tests specified in 6.2 and 6.3 shall

40、 be carried out in a test frame (see Figure 1), which is so constructed that the deformation under the applied loads is no more than 1 mm. Hinges for wooden doors shall be mounted on particle board, 5.3, unless otherwise specified. Hinges for other materials, e.g. glass, metal or plastic shall be mo

41、unted according to the manufacturers instructions. The position of hinges and components on the door and the test frame as well as the size and weight of the door shall be as specified by the manufacturer, see Annex A. In cases where the door parameters (e.g. height, width, mass) are not specified b

42、y the manufacturer, the tests may be carried out using the standard door sizes specified in Annex B. DIN EN 15570:2008-08 EN 15570:2008 (E) 8 Key 1 test door 2 test sides 3 test frame Figure 1 Test frame and test door DIN EN 15570:2008-08 EN 15570:2008 (E) 9 5.3 Particle board properties The propert

43、ies of the particle board shall be as specified in Table 1. Table 1 Particle board properties Property Reference standard Requirement Axial withdrawal of screws EN 320:1993 1 100 100 N Density EN 323:1993 0,65 0,05 g/cm36 Test procedures and requirements 6.1 General For the following tests, three se

44、ts of hinges shall be used as follows: The first set shall be used for the first test sequence specified in 6.2. The second set shall be used for the second test sequence specified in 6.3. The third set shall be used for the corrosion test specified in 6.4. All overload and functional tests shall be

45、 carried out according to the same column (1, 2 or 3) in Annex B (normative). 6.2 Overload tests 6.2.1 Vertical static overload Load the door as shown in Figure 2 with the mass specified in Annex B. The mass shall be suspended 100 mm from the edge furthest from the hinge. Open and close the door 10

46、full cycles (back and forth) from a position 45o from fully closed to a position 10ofrom fully opened, up to a maximum of 135ofrom the fully closed position. Opening and closing can be done by hand using 3 s to 5 s for opening and 3 s to 5 s for closing. Carry out inspection and assessment according

47、 to 4.6 without the test load. The door and/or hinges shall not become detached. DIN EN 15570:2008-08 EN 15570:2008 (E) 10 Key 1 100 mm 2 45 3 test frame 4 test sides Figure 2 Vertical static overload 6.2.2 Horizontal static overload This test applies only to hinges with an opening angle 135. Apply

48、the horizontal static load specified in Annex B 10 times perpendicular to the plane of the door on its horizontal centreline 100 mm from the edge furthest from the hinge, as shown in Figure 3. Carry out inspection and assessment according to 4.6 without the test load. The door, hinges or their compo

49、nents shall not become detached. DIN EN 15570:2008-08 EN 15570:2008 (E) 11 Key 1 100 mm 2 door height 3 half door height Figure 3 Horizontal static overload 6.3 Functional tests 6.3.1 General During testing according to 6.3, the test door shall be loaded according to Annex A and Annex B. 6.3.2 Operating forces 6.3.2.1 General The operating forces shall be measured before and after the durability test. The measurements of operating forces shall be made with the door unloaded. 6.3.2.2 Closing force, hinges with self-clo