DIN EN 1555-3-2013 Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 3 Fittings German version EN 1555-3 2010+A1 2012《气体燃料供应用塑料管道系统 聚乙烯 (PE) 第3部分 配件 德文.pdf

《DIN EN 1555-3-2013 Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 3 Fittings German version EN 1555-3 2010+A1 2012《气体燃料供应用塑料管道系统 聚乙烯 (PE) 第3部分 配件 德文.pdf》由会员分享，可在线阅读，更多相关《DIN EN 1555-3-2013 Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 3 Fittings German version EN 1555-3 2010+A1 2012《气体燃料供应用塑料管道系统 聚乙烯 (PE) 第3部分 配件 德文.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、January 2013 Translation by DIN-Sprachendienst.English price group 14No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 23.040.45!$e“1936166www.din.deDDIN EN 1555-3Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 3: Fittings;English version EN 1555-3:2010+A1:2012,English translation of DIN EN 1555-3:2013-01Kunststoff-Rohrleitungssysteme fr die Gasversorgung Polyethylen (PE) Teil 3: For

3、mstcke;Englische Fassung EN 1555-3:2010+A1:2012,Englische bersetzung von DIN EN 1555-3:2013-01Systmes de canalisations en plastique pour la distribution de combustibles gazeux Polythylne (PE) Partie 3: Raccords;Version anglaise EN 1555-3:2010+A1:2012,Traduction anglaise de DIN EN 1555-3:2013-01Super

4、sedesDIN EN 1555-3:2011-08www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 32 pages 12.12 DIN EN 1555-3:2013-01 2 A comma is used as the decimal marker. National foreword This document (EN 1555-3:2010+A1:2012) has been prepared by Techni

5、cal Committee CEN/TC 155 “Plas-tics piping systems and ducting systems” (Secretariat: NEN, Netherlands). The responsible German body involved in its preparation was the Normenausschuss Kunststoffe (Plastics Standards Committee), Working Committee NA 054-05-08 AA Kunststoff-Rohrleitungssysteme fr die

6、 Gas-versorgung. Amendments This standard differs from DIN EN 1555-3:2011-08 as follows: a) Amendment 1 to EN 1555-3:2010 has been incorporated; b) footnote b in Table 4 “Mechanical characteristics” relating to the calculation of the test pressure has been modified; c) in Table 8 “Minimum required m

7、arking”, it has been specified that the information about the intended use may also be printed on a label. Previous editions DIN EN 1555-3: 2003-04, 2005-08, 2010-12, 2011-08 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1555-3:2010+A1 November 2012 ICS 23.040.45 Supersedes EN 1555-3:2010Engl

8、ish Version Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings Systmes de canalisations en plastique pour la distribution de combustibles gazeux - Polythylne (PE) - Partie 3 : Raccords Kunststoff-Rohrleitungssysteme fr die Gasversorgung - Polyethylen (PE)

9、- Teil 3: Formstcke This European Standard was approved by CEN on 30 July 2010 and includes Amendment 1 approved by CEN on 4 September 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a nati

10、onal standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A ver

11、sion in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus,

12、Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom

13、. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1555-3:2010+A1:2012: E

14、EN 1555-3:2010+A1:2012 (E) 2 Contents Page Foreword 4Introduction .61 Scope 72 Normative references 73 Terms and definitions, symbols and abbreviations .94 Material 104.1 PE Compound . 104.2 Material for non-polyethylene parts 104.2.1 General . 104.2.2 Metal parts . 104.2.3 Elastomers . 104.2.4 Othe

15、r materials 105 General characteristics 115.1 Appearance . 115.2 Colour 115.3 Design 115.4 Appearance of factory made joints . 115.5 Electrical characteristics for electrofusion fittings . 116 Geometrical characteristics . 126.1 Measurement of dimensions . 126.2 Dimensions of electrofusion socket fi

16、ttings 126.2.1 Diameters and lengths of electrofusion sockets . 126.2.2 Wall thicknesses . 136.2.3 Out-of-roundness of the bore of a fitting (at any point) 146.2.4 Spigots . 146.2.5 Other dimensions . 146.3 Dimensions of electrofusion saddle fittings 146.4 Dimensions of spigot end fittings . 156.4.1

17、 Diameters and lengths . 156.4.2 Wall thickness of the fusion end . 176.4.3 Wall thickness of the fitting body . 176.4.4 Other dimensions . 186.5 Dimensions of mechanical fittings . 186.5.1 General . 186.5.2 Mechanical fittings with polyethylene spigot ends . 186.5.3 Mechanical fittings with polyeth

18、ylene electrofusion sockets 186.5.4 Threads 187 Mechanical characteristics 187.1 General . 187.2 Requirements 197.3 Performance requirements 218 Physical characteristics . 218.1 Conditioning 218.2 Requirements 219 Performance requirements 2210 Marking 2210.1 General . 2210.2 Minimum required marking

19、 of fittings 22DIN EN 1555-3:2013-01 EN 1555-3:2010+A1:2012 (E) 3 10.3 Additional marking 2310.4 Fusion system recognition . 2311 Delivery conditions . 23Annex A (informative) Examples of typical terminal connection for electrofusion fittings 24Annex B (normative) Short-term pressure test method . 2

20、6B.1 Principle 26B.2 Apparatus . 26B.3 Test piece . 26B.4 Procedure . 26B.5 Test report 27Annex C (normative) Tensile test for fitting/pipe assemblies 28C.1 Principle 28C.2 Apparatus . 28C.3 Test piece . 28C.4 Procedure . 28C.5 Test report 28Bibliography 30DIN EN 1555-3:2013-01 EN 1555-3:2010+A1:201

21、2 (E) 4 Foreword This document (EN 1555-3:2010+A1:2012) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an ide

22、ntical text or by endorsement, at the latest by May 2013, and conflicting national standards shall be withdrawn at the latest by May 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held respon

23、sible for identifying any or all such patent rights. This document includes Amendment 1 approved by CEN on 4 September 2012. This document supersedes !EN 1555-3:2010“. The start and finish of text introduced or altered by amendment is indicated in the text by tags !“. !Due to Amendment 1 to EN 1555-

24、3:2010, this document comprises technical changes to: Subclause 7.2, Requirements; Subclause 10.2, Minimum required marking of fittings.“ EN 1555 consists of the following parts: EN 1555-1, Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 1: General; EN 1555-2, Plastics

25、 piping systems for the supply of gaseous fuels Polyethylene (PE) Part 2: Pipes; EN 1555-3, Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 3: Fittings (this standard); prEN 1555-4, Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 4: Valve

26、s; EN 1555-5, Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 5: Fitness for purpose of the system; CEN/TS 1555-7, Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 7: Guidance for assessment of conformity. NOTE EN 12007-2:2000 1 prepared b

27、y CEN/TC 234 “Gas infrastructure” deals with the recommended practice for installation of plastics pipes system in accordance with EN 1555 (all parts). System Standards are based on the results of the work being undertaken in ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluid

28、s“, which is a Technical Committee of the International Organization for Standardization (ISO). They are supported by separate standards on test methods to which references are made throughout the System Standard. The System Standards are consistent with general standards on functional requirements

29、and on recommended practice for installation. DIN EN 1555-3:2013-01 EN 1555-3:2010+A1:2012 (E) 5 According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cypr

30、us, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United

31、 Kingdom. DIN EN 1555-3:2013-01 EN 1555-3:2010+A1:2012 (E) 6 Introduction The System Standard, of which this is Part 3, specifies the requirements for a piping system and its components made from polyethylene (PE) and which is intended to be used for the supply of gaseous fuels. Requirements and tes

32、t methods for material and components, other than fittings, are specified in EN 1555-1, EN 1555-2 and prEN 1555-4 9. Characteristics for fitness for purpose are covered in EN 1555-5. CEN/TS 1555-7 2 gives guidance for assessment of conformity. Recommended practice for installation is given in EN 120

33、07-2:2000 1 prepared by CEN/TC 234. This part of EN 1555 covers the characteristics of fittings. DIN EN 1555-3:2013-01 EN 1555-3:2010+A1:2012 (E) 7 1 Scope This !European Standard“ specifies the characteristics of fusion fittings made from polyethylene (PE) as well as of mechanical fittings for pipi

34、ng systems in the field of the supply of gaseous fuels. It also specifies the test parameters for the test methods referred to in this standard. In conjunction with Parts 1, 2, 4 and 5 of EN 1555, it is applicable to PE fittings, their joints and to joints with components of PE and other materials i

35、ntended to be used under the following conditions: a) a maximum operating pressure, MOP, up to and including 10 bar 1); b) an operating temperature of 20 C as reference temperature. NOTE 1 For other operating temperatures, derating coefficients should be used; see EN 1555-5. EN 1555 (all parts) cove

36、rs a range of maximum operating pressures and gives requirements concerning colours and additives. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulati

37、ons and installation practices or codes. This European Standard is applicable for fittings of the following types: c) electrofusion socket fittings; d) electrofusion saddle fittings; e) spigot end fittings (for butt fusion using heated tools and electrofusion socket fusion); f) mechanical fittings.

38、The fittings can e.g. be in the form of couplers, equal and reduced tees, reducers, bends or caps. 2 Normative references !The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited

39、 applies. For undated references, the latest edition of the referenced document (including any amendments) applies.“ EN 682:2002, Elastomeric Seals Materials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids EN 1555-1:2010, Plastics piping systems for the supply o

40、f gaseous fuels Polyethylene (PE) Part 1: General EN 1555-2, Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 2: Pipes EN 1555-5, Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 5: Fitness for purpose of the system EN 1716, Plastics piping

41、 systems Polyethylene (PE) tapping tees Test method for impact resistance of an assembled tapping tee 1) 1 bar = 0,1 MPa. DIN EN 1555-3:2013-01 EN 1555-3:2010+A1:2012 (E) 8 EN 10226-1, Pipe threads where pressure tight joints are made on the threads Part 1: Taper external threads and parallel intern

42、al threads Dimensions, tolerances and designation EN 10226-2, Pipe threads where pressure tight joints are made on the threads Part 2: Taper external threads and taper internal threads Dimensions, tolerances and designation EN 12117, Plastics piping systems Fittings, valves and ancillaries Determina

43、tion of gaseous flow rate/pressure drop relationships EN ISO 228-1:2000, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) EN ISO 1133, Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow

44、rate (MVR) of thermoplastics (ISO 1133:2005) EN ISO 1167-1:2006, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method (ISO 1167-1:2006) EN ISO 1167-4, Thermoplastics pipes, fittings and assemblies for t

45、he conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies (ISO 1167-4:2007) EN ISO 3126, Plastics piping systems Plastics components Determination of dimensions (ISO 3126:2005) ISO 10838-1 2), Mechanical fittings for polyethylene piping systems fo

46、r the supply of gaseous fuels Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm ISO 10838-2 2), Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm I

47、SO 10838-3 2), Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 3: Thermoplastic fittings for pipes of nominal outside diameter less than or equal to 63 mm ISO 11357-6:2008, Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation in

48、duction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) ISO 13950, Plastics pipes and fittings Automatic recognition systems for electrofusion joints ISO 13951:2001, Plastics piping systems Test method for the resistance of polyolefin pipe/pipe or pipe/fitting assemblies to tensile lo