DIN EN 15267-1-2009 Air quality - Certification of automated measuring systems - Part 1 General principles English version of DIN EN 15267-1 2009-07《空气质量 自动测量系统的质量保证 第1部分 一般原则 英文版本.pdf

《DIN EN 15267-1-2009 Air quality - Certification of automated measuring systems - Part 1 General principles English version of DIN EN 15267-1 2009-07《空气质量 自动测量系统的质量保证 第1部分 一般原则 英文版本.pdf》由会员分享，可在线阅读，更多相关《DIN EN 15267-1-2009 Air quality - Certification of automated measuring systems - Part 1 General principles English version of DIN EN 15267-1 2009-07《空气质量 自动测量系统的质量保证 第1部分 一般原则 英文版本.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、July 2009DEUTSCHE NORM English price group 11No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 13.040.99!$Xtm“1538174www

2、.din.deDDIN EN 15267-1Air quality Certification of automated measuring systems Part 1: General principlesEnglish version of DIN EN 15267-1:2009-07Luftbeschaffenheit Zertifizierung von automatischen Messeinrichtungen Teil 1: GrundlagenEnglische Fassung DIN EN 15267-1:2009-07www.beuth.deDocument compr

3、ises pages19This standard has been included in the VDI/DIN Handbook on air quality, Volume 5.2 National foreword This standard has been prepared by Technical Committee CEN/TC 264 “Air quality”, Working Group WG 22 “Certification scheme for AMS” (Secretariat: DIN, Germany). The responsible German bod

4、y involved in its preparation was the Kommission Reinhaltung der Luft (KRdL) im VDI und DIN (Commission on Air Pollution Prevention of VDI and DIN Standards Committee), Section IV Umweltmesstechnik. DIN EN 15267-1:2009-07 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15267-1 March 2009 ICS 13

5、.040.99 English Version Air quality Certification of automated measuring systems Part 1: General principles Qualit de lair Certification des systmes de mesurage automatiss Partie 1: Principes gnraux Luftbeschaffenheit Zertifizierung von automatischen Messeinrichtungen Teil 1: Grundlagen This Europea

6、n Standard was approved by CEN on 14 February 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references conc

7、erning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its ow

8、n language and notified to the CEN Management Centre has the same status as theofficial versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuani

9、a, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN A

10、ll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15267-1:2009: EEN 15267-1:2009 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .6 4 Abbreviations .7 5 Principles 7 5.1 Performanc

11、e testing of the automated measuring system .7 5.2 Initial assessment of the AMS manufacturers quality management system .8 5.3 Certification 8 5.4 Surveillance 8 6 Roles and responsibilities 9 6.1 General 9 6.2 Roles and responsibilities of the manufacturer .9 6.3 Roles and responsibilities of the

12、test laboratory .9 6.4 Roles and responsibilities of the relevant body 10 7 Certification procedure 11 7.1 General . 11 7.2 Performance testing of the automated measuring system 11 7.3 Initial assessment of the manufacturers quality management system . 11 7.4 Certification . 11 7.5 Surveillance . 12

13、 7.6 Review of certifications 13 Annex A (informative) Application and assessment processes 14 Annex B (informative) Example certificate template . 15 Bibliography . 17 DIN EN 15267-1:2009-07 EN 15267-1:2009 (E) 3 Foreword This document (EN 15267-1:2009) has been prepared by Technical Committee CEN/

14、TC 264 “Air quality”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2009, and conflicting national standards shall be withdrawn at the latest b

15、y September 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document is Part 1 of a series of European Standards: EN 15267-

16、1, Air quality Certification of automated measuring systems Part 1: General principles EN 15267-2, Air quality Certification of automated measuring systems Part 2: Initial assessment of the AMS manufacturers quality management system and post certification surveillance for the manufacturing process

17、EN 15267-3, Air quality Certification of automated measuring systems Part 3: Performance criteria and test procedures for automated measuring systems for monitoring emissions from stationary sources According to the CEN/CENELEC Internal Regulations, the national standards organizations of the follow

18、ing countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slove

19、nia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN 15267-1:2009-07 EN 15267-1:2009 (E) 4 Introduction The certification of automated measuring systems (AMS) supports the requirements of certain Directives of the European Union (EU), which require, either directly or indirectly, that AMS

20、comply with performance criteria, maximum permissible measurement uncertainties and testing requirements. These Directives include the Directive on the limitation of emissions of certain pollutants into the air from large combustion plants 1, the Directive on the incineration of waste 2 and the Fram

21、ework Directive on ambient air quality assessment and management 3 and the associated daughter directives 4, 5, 6 and 7. The responsibility for approving AMS for monitoring ambient air quality under Directive 96/62/EC lies with the national competent authority or a body designated by the EU member s

22、tate. No explicit requirement for approving AMS for monitoring emissions from stationary sources is defined in the relevant EU Directives, although the competent authorities in some EU member states have such arrangements in place. In some EU member states the competent authority delegates the respo

23、nsibility for approval of AMS to a certification body accredited to EN 45011 by national accreditation bodies. In some EU member states the competent authority cannot be accredited by external bodies, in others they may be. These approaches have built up over many years and reflect the different adm

24、inistrative and legal arrangements that exist in the EU member states. In order to recognize these different approaches, this European Standard uses the collective term “relevant body” when referring to competent authority or certification body. The terms “competent authority” and “certification bod

25、y” are only used where it is necessary to be specific for the purpose of clarity in the way in which a requirement applies under the different approaches. The European Standard EN 45011 specifies general criteria that a certification body operating product certification shall follow if it is to be r

26、ecognized at a national or European level as competent and reliable in the operation of a product certification system, irrespective of the sector involved. It is intended for the use of accreditation bodies concerned with recognizing the competence of certification bodies. EN 45011 is identical to

27、ISO/IEC Guide 65. The document EA-6/01 8 published by the International Accreditation Forum (IAF) provides guidelines on the application of EN 45011. The purpose of EA-6/01 is to harmonise the worldwide application of EN 45011 by accreditation bodies as an important step towards mutual recognition b

28、etween certification bodies under the IAF Multilateral Agreement (MLA). EN 45011 recognizes that these general criteria may have to be supplemented when applied to a particular sector. This European Standard provides guidance on the application of EN 45011 to the certification of AMS for monitoring

29、ambient air quality and emissions from stationary sources. It is Part 1 of a three part series of European Standards, which specify common requirements for the certification of AMS in EU member states. This European Standard defines common procedures and requirements for the certification of AMS to

30、facilitate mutual recognition by the relevant bodies and thereby minimise administrative and cost burdens on AMS manufacturers seeking certification in multiple member states. It also describes the roles and responsibilities of manufacturers, test laboratories, certification bodies (for quality mana

31、gement systems) and relevant bodies under these procedures. DIN EN 15267-1:2009-07 EN 15267-1:2009 (E) 5 1 Scope This European Standard specifies the general principles, including common procedures and requirements, for the product certification of automated measuring systems (AMS) for monitoring am

32、bient air quality and emissions from stationary sources. This product certification consists of the following sequential stages: a) performance testing of an automated measuring system; b) initial assessment of the AMS manufacturers quality management system; c) certification; d) surveillance. This

33、European Standard applies to the certification of all AMS for monitoring ambient air quality and emissions from stationary sources for which performance criteria and test procedures are available in European Standards. 2 Normative references The following referenced documents are indispensable for t

34、he application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 14211, Ambient air quality Standard method for the measurement of the concentration of nitrogen dioxide

35、and nitrogen monoxide by chemiluminescence EN 14212, Ambient air quality Standard method for the measurement of the concentration of sulphur dioxide by ultraviolet fluorescence EN 14625, Ambient air quality Standard method for the measurement of the concentration of ozone by ultraviolet photometry E

36、N 14626, Ambient air quality Standard method for the measurement of the concentration of carbon monoxide by nondispersive infrared spectroscopy EN 14662-3, Ambient air quality Standard method for measurement of benzene concentrations Part 3: Automated pumped sampling with in situ gas chromatography

37、EN 15267-2, Air quality Certification of automated measuring systems Part 2: Initial assessment of the AMS manufacturers quality management system and post certification surveillance for the manufacturing process EN 15267-3, Air quality Certification of automated measuring systems Part 3: Performanc

38、e criteria and test procedures for automated measuring systems for monitoring emissions from stationary sources EN 45011, General requirements for bodies operating product certification systems (ISO/IEC Guide 65:1996) EN ISO 9001, Quality management systems Requirements (ISO 9001:2000) EN ISO/IEC 17

39、021, Conformity assessment Requirements for bodies providing audit and certification of management systems (ISO/IEC 17021:2006) EN ISO/IEC 17025, General requirements for the competence of testing and calibration laboratories (ISO/IEC 17025:2005) DIN EN 15267-1:2009-07 EN 15267-1:2009 (E) 6 3 Terms

40、and definitions For the purposes of this document, the following terms and definitions apply. 3.1 automated measuring system AMS entirety of all measuring instruments and additional devices for obtaining a result of measurement NOTE 1 Apart from the actual measuring device (the analyser), an AMS inc

41、ludes facilities for taking samples (e.g. probe, sample gas lines, flow meters and regulator, delivery pump) and for sample conditioning (e.g. dust filter, pre-separator for interferents, cooler, converter). This definition also includes testing and adjusting devices that are required for functional

42、 checks and, if applicable, for commissioning. NOTE 2 The term “automated measuring system” (AMS) is typically used in Europe. The terms “continuous emission monitoring system” (CEM) and “continuous ambient-air-quality monitoring system” (CAM) are also typically used in the UK and USA. 3.2 relevant

43、body competent authority or certification body, nominated by a competent authority or EU member state, that carries out the certification of automated measuring systems 3.3 competent authority organisation which implements the requirements of EU Directives and regulates installations, which must com

44、ply with the requirements of applicable European Standards 3.4 certification body any body operating a product certification system or any body accredited to EN ISO/IEC 17021 for the certification of quality management systems 3.5 manufacturer organisation, situated at a stated location or locations

45、, that carries out or controls such stages in the manufacture, assessment, handling and storage of a product that enables it to accept responsibility for continued compliance of the product and its certification, and undertakes all obligations in that connection NOTE The term “manufacturer“ is used

46、instead of “organisation“ as used in EN ISO 9001. For the purpose of this document they are interchangeable. 3.6 test laboratory laboratory accredited to EN ISO/IEC 17025 for carrying out the performance tests on automated measuring systems in accordance with applicable European Standards 3.7 produc

47、t automated measuring system 3.8 technical file record of the reference documents and design changes to the reference documents 3.9 reference document document that controls the manufacture and design of an AMS and is referenced in the test report NOTE Reference documents can include drawings, speci

48、fications, instructions and computer code. DIN EN 15267-1:2009-07 EN 15267-1:2009 (E) 7 3.10 related document document not referenced in the test report NOTE A related document can be used, for example, for the detailed manufacture of component parts. 3.11 certification range range over which the au

49、tomated measuring system is tested and certified for compliance with the relevant performance criteria NOTE 1 The lower limit is typically the detection limit of the AMS and often considered to be zero. NOTE 2 Generally, the lower the certification range, the better the performance of the AMS. Also an AMS typically performs satisfactorily at higher values over the measurement range. 3.12 surveillance systematic iteration of conformity assessment activities as a basis for maintaining the validity of the s