DIN 22102-2-2014 Conveyor belts with textile plies for bulk goods - Part 2 Testing《松散物料用带织物层的输送机皮带 第2部分 检验》.pdf

《DIN 22102-2-2014 Conveyor belts with textile plies for bulk goods - Part 2 Testing《松散物料用带织物层的输送机皮带 第2部分 检验》.pdf》由会员分享，可在线阅读，更多相关《DIN 22102-2-2014 Conveyor belts with textile plies for bulk goods - Part 2 Testing《松散物料用带织物层的输送机皮带 第2部分 检验》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、January 2014 English price group 6No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 53.040.20!%?Du“2283382www.din.deD

2、IN 22102-2Conveyor belts with textile plies for bulk goods Part 2: Testing,English translation of DIN 22102-2:2014-01Textil-Frdergurte fr Schttgter Teil 2: Prfung,Englische bersetzung von DIN 22102-2:2014-01Courroies transporteuses textiles pour produits en vrac Partie 2: Essai,Traduction anglaise d

3、e DIN 22102-2:2014-01Together with DIN EN ISO 583:2008-03,supersedesDIN 22102-2:1991-04www.beuth.deDocument comprises 7 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.12.16DIN 22102-2:2014-01 A comma is used as the decimal mar

4、ker. Contents Page Foreword . 3 1 Scope 5 2 Normative references 5 3 Testing . 6 3.1 Number of test pieces, number of samples, evaluation . 6 3.2 Width of conveyor belt 6 3.3 Length of conveyor belt . 6 3.3.1 Endless belts 6 3.3.2 Open belts . 7 3.4 Thickness of conveyor belt 7 3.5 Cover thickness,

5、interlayer thickness 7 3.6 Elongation with static loading under the reference load, breaking load 7 3.7 Resistance to separation . 7 3.8 Covers. 7 3.8.1 Tensile strength at break and elongation at break . 7 3.8.2 Abrasive wear . 7 3.8.3 Ageing 7 3.9 Electrical and flammability safety requirements 7

6、3.10 Troughability 7 2 DIN 22102-2:2014-01 Foreword A revision of DIN 22102-2 and its publication as a national residual standard have been necessary because large portions of it are not contained in the following standards: DIN EN 1554, Conveyor belts Drum friction testing DIN EN 12881-1, Conveyor

7、belts Fire simulation flammability testing Part 1: Propane burner tests DIN EN ISO 252, Conveyor belts Adhesion between constitutive elements Test methods DIN EN ISO 283, Textile conveyor belts Full thickness tensile strength, elongation at break and elongation at the reference load Test method DIN

8、EN ISO 284, Conveyor belts Electrical conductivity Specification and type testing DIN EN ISO 340, Conveyor belts Laboratory scale flammability characteristics Requirements and test methods DIN EN ISO 583, Conveyor belts with a textile carcass Total belt thickness and thickness of constitutive elemen

9、ts Test methods DIN EN ISO 703, Conveyor belts Transverse flexibility (troughability) Test method The responsible German body involved in the preparation of this standard was Working Committee NA 045-02-05 AA Frdergurte of the Normenausschuss Kautschuktechnik (FAKAU) (Rubber Technology Standards Com

10、mittee). DIN 22102 consists of the following parts under the general title Conveyor belts with textile plies for bulk goods: Part 1: Dimensions, specifications, marking Part 2: Testing Part 3: Permanent joints Attention is drawn to the possibility that some of the elements of this document may be th

11、e subject of patent rights. DIN and/or DKE shall not be held responsible for identifying any or all such patent rights. 3DIN 22102-2:2014-01 Amendments This standard differs from DIN 22102-2:1991-04 as follows: a) it has been brought in line with the current rules of presentation; b) the standard ha

12、s been editorially revised; c) Subclause 2.4 “Thickness of belt” has been revised and is now in DIN EN ISO 583; d) Subclause 2.5 “Thickness of covers and interlayers” has been revised and is now in DIN EN ISO 583; e) Subclause 2.6 “Elongation with static loading under standard load, breaking load” h

13、as been revised and is now in DIN EN ISO 283; f) Subclause 2.7 “Resistance to separation” has been revised and is now in DIN EN ISO 252; g) Subclause 2.9 “Fire resistance” has been revised and is now in DIN EN ISO 340, DIN EN 1554 and DIN EN 12881-1; h) Subclause 2.10 “Electrical properties” has bee

14、n revised and is now in DIN EN ISO 284; i) Subclause 2.11 “Troughability” has been revised and is now in DIN EN ISO 703. Previous editions DIN BERG 2102-1: 1934-10 DIN BERG 2102-2: 1934-10 DIN 22102-1: 1943-09, 1952-01 DIN 22102-2: 1943-09, 1951-10, 1991-04 DIN 22102: 1968-03, 1970-09 4 DIN 22102-2:

15、2014-01 1 Scope This standard applies to the testing of conveyor belts with textile plies for bulk goods which are in accordance with DIN 22102-1 and DIN EN ISO 14890. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensab

16、le for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. DIN 22102-1, Conveyor belts with textile plies for bulk goods Part 1: Dimensions, specifications, marking DIN 53504,

17、 Testing of rubber Determination of tensile strength at break, tensile stress at yield, elongation at break and stress values in a tensile test DIN 53508:2000-03, Testing of rubber Accelerated ageing DIN EN 1554, Conveyor belts Drum friction testing DIN EN 12881-1, Conveyor belts Fire simulation fla

18、mmability testing Part 1: Propane burner tests DIN EN ISO 252, Conveyor belts Adhesion between constitutive elements Test methods DIN EN ISO 283, Textile conveyor belts Full thickness tensile strength, elongation at break and elongation at the reference load Test method DIN EN ISO 284, Conveyor belt

19、s Electrical conductivity Specification and type testing DIN EN ISO 340, Conveyor belts Laboratory scale flammability characteristics Requirements and test methods DIN EN ISO 583, Conveyor belts with a textile carcass Total belt thickness and thickness of constitutive elements Test methods DIN EN IS

20、O 703, Conveyor belts Transverse flexibility (troughability) Test method DIN EN ISO 14890, Conveyor belts Specification for rubber- or plastics-covered conveyor belts of textile construction for general use DIN EN ISO 16851, Textile conveyor belts Determination of the net length of an endless (splic

21、ed) conveyor belt DIN ISO 4649:2006-11, Rubber, vulcanized or thermoplastic Determination of abrasion resistance using a rotating cylindrical drum device 5DIN 22102-2:2014-01 3 Testing 3.1 Number of test pieces, number of samples, evaluation Table 1 specifies the number of test pieces. Table 1 Numbe

22、r of test pieces Total length m Number of test pieces Up to 500 1 Over 500 up to 1000 2 Over 1000 up to 2000 3 Over 2000 up to 3500 4 Over 3500 up to 5000 5 Over 5000 up to 7000 6 Over 7000 up to 10000 7 Over 10000 1 each for every further 5000 m For conveyor belts which are supplied in fixed length

23、s, a test piece shall also be supplied if the manufacturer so requests. Test pieces shall be of sufficient length. All tests shall be carried out on three samples, except for the resistance to separation test, which shall be carried out on two samples. The mean of the individual results shall be cal

24、culated. If an individual result differs from the mean value by more than 10 %, this result shall be rejected and three new samples taken from the area immediately adjacent. The final mean value is to be calculated from these three values and the two remaining values. Samples shall be taken from are

25、as distributed over the entire width of the conveyor belt but at least 50 mm from the belt edges. Testing shall be carried out no earlier than two days after the belt has been manufactured. 3.2 Width of conveyor belt The conveyor belt width, B, shall be determined to the nearest 1 mm. 3.3 Length of

26、conveyor belt The length of the conveyor belt shall be given to the nearest 10 mm for belts up to 20 m long, and to the nearest 100 mm for belts longer than 20 m. 3.3.1 Endless belts For endless belts, the inside length shall be measured in accordance with DIN EN ISO 16851. This is done by laying th

27、e belt out straight, measuring the bends and the flat parts, and adding the single lengths together to obtain the total inside length. 6 DIN 22102-2:2014-01 3.3.2 Open belts For open belts, the belt is to be laid out straight and measured in several lengths, if necessary. The belt length is then obt

28、ained by adding together the single lengths. 3.4 Thickness of conveyor belt Testing as in DIN EN ISO 583. 3.5 Cover thickness, interlayer thickness Testing as in DIN EN ISO 583. 3.6 Elongation with static loading under the reference load, breaking load Testing as in DIN EN ISO 283. 3.7 Resistance to

29、 separation Testing as in DIN EN ISO 252. 3.8 Covers 3.8.1 Tensile strength at break and elongation at break Testing as in DIN 53504. Test pieces (S 2 dumb-bell type) shall be taken in the longitudinal direction from covers which have been stripped or peeled off. Tensile strength at break values sha

30、ll be rounded to the nearest 0,1 N/mm . 2Elongation at break values shall be rounded to the nearest 10 %.Covers having a thickness 1,5 mm shall not be tested. 3.8.2 Abrasive wear Testing as in DIN ISO 4649:2006-11, Method A. Results shall be rounded to the nearest whole number. 3.8.3 Ageing Samples

31、for determining separation resistance and tensile strength at break shall be aged at (70 1) C for 168 h in a natural convection oven as in DIN 53508:2000-03, 6.3. The results obtained shall be given as a percentage (%) of the value in the unaged condition. 3.9 Electrical and flammability safety requirements Testing as in DIN EN ISO 284. Testing as in DIN EN ISO 340. Testing as in DIN EN ISO 1554. Testing as in DIN EN ISO 12881-1, Method A. 3.10 Troughability Testing as in DIN EN ISO 703. 7