BS ISO 15016-2015 Ships and marine technology Guidelines for the assessment of speed and power performance by analysis of speed trial data《船舶和海上技术 用速度试验数据分析法对速度和动力性能进行评定的导则》.pdf

《BS ISO 15016-2015 Ships and marine technology Guidelines for the assessment of speed and power performance by analysis of speed trial data《船舶和海上技术 用速度试验数据分析法对速度和动力性能进行评定的导则》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 15016-2015 Ships and marine technology Guidelines for the assessment of speed and power performance by analysis of speed trial data《船舶和海上技术 用速度试验数据分析法对速度和动力性能进行评定的导则》.pdf（96页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 15016:2015Ships and marine technology Guidelines for theassessment of speed andpower performance by analysisof speed trial dataBS ISO 15016:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 15016:2015. Itsupersedes BS ISO 1501

2、6:2002 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee EPL/80, Maritime navigation and radiocommunicationequipment and systems.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not pur

3、port to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2015. Published by BSI StandardsLimited 2015ISBN 978 0 580 80101 3ICS 47.020.01Compliance with a British Standard cannot confer immunity fromlegal obligation

4、s.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 April 2015.Amendments issued since publicationDate Text affectedBS ISO 15016:2015 ISO 2015Ships and marine technology Guidelines for the assessment of speed and power performance by analysis

5、 of speed trial dataNavires et technologie maritime Lignes directrices pour lvaluation des performances de vitesse et de puissance par analyse des donnes dessais de vitesseINTERNATIONAL STANDARDISO15016Second edition2015-04-01Reference numberISO 15016:2015(E)BS ISO 15016:2015ISO 15016:2015(E)ii ISO

6、2015 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2015All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet,

7、without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in Sw

8、itzerlandBS ISO 15016:2015ISO 15016:2015(E)Foreword vIntroduction vi1 Scope . 12 Normative references 23 Terms and definitions . 24 Symbols and abbreviated terms . 44.1 Symbols . 44.2 Abbreviated terms . 85 Responsibilities . 85.1 Ship builders responsibilities . 85.2 The Trial Team. 96 Trial prepar

9、ations . 96.1 Step 1: Installation and Calibration . 96.2 Step 2: S/P trial agenda and pre-trial meeting .107 Ships condition.117.1 Displacement . 117.2 Trim . 117.3 Hull and propeller . 118 Trial boundary conditions .118.1 Location 128.2 Wind 128.3 Sea state . 128.4 Water depth 138.5 Current 149 Tr

10、ial procedures 149.1 Parameters that shall be recorded 149.2 Parameters measured during each run 149.3 Parameters measured at the speed trial site . 159.4 General information 159.5 Tank test information . 159.6 Scope and conduct of the measurements . 169.6.1 Ship track and speed over ground . 169.6.

11、2 Torque 169.6.3 Wind 169.6.4 Water depth .169.6.5 Waves 169.6.6 Temperature and density 179.6.7 Current. 1710 Conduct of the trial 1710.1 Initiation 1710.2 Ships track during trial 1710.3 Run duration and timing . 1810.4 Trial direction . 1810.5 Steering . 1810.6 Approach . 1810.7 Number of speed r

12、uns . 1810.7.1 Iterative method .1810.7.2 Mean of means method 1911 Data acquisition1911.1 General data 20 ISO 2015 All rights reserved iiiContents PageBS ISO 15016:2015ISO 15016:2015(E)11.2 Data on each run . 2011.3 Acquisition system 2111.3.1 Minimum data .2111.3.2 System requirements 2111.3.3 Loc

13、ation 2211.4 Manual data collection 2212 Analysis procedure 2412.1 General remarks . 2412.2 Description of the analysis procedure . 2412.2.1 Resistance data derived from the acquired data .2512.2.2 Evaluation of the acquired data . 2512.2.3 Evaluation based on Direct Power Method 2612.2.4 Correction

14、 of the measured ships speed due to the effect of current 2912.2.5 Correction of the ships speed due to the effects of shallow water .3012.2.6 Correction of the ships performance due to the effects of displacement .3012.2.7 Conversion of power curve from trial condition to full load/stipulated condi

15、tion .3013 Processing of the results .3014 Reporting .3115 Example of speed trial data analysis 32Annex A (normative) General information and trial log sheet 34Annex B (normative) Beaufort scale for wind velocity 35Annex C (normative) Resistance increase due to wind 38Annex D (normative) Resistance

16、increase due to waves 48Annex E (normative) Effect of water temperature and water density61Annex F (normative) Effect of current .62Annex G (normative) Effect of shallow water .66Annex H (normative) Effect of displacement 67Annex I (normative) Conversion from trial condition to other stipulated load

17、 conditions .68Annex J (normative) Derivation of load variation coefficients 70Annex K (informative) Analysis of direct power method .75Bibliography .85iv ISO 2015 All rights reservedBS ISO 15016:2015ISO 15016:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide fed

18、eration of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that comm

19、ittee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document an

20、d those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Par

21、t 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of th

22、e document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific term

23、s and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 8, Ships and marine technolo

24、gy, Subcommittee SC 6, Navigation and ship operations.This second edition cancels and replaces the first edition (ISO 15016:2002), which has been technically revised.Annexes A, B, C, D, E, F, G, H, I and J form a normative part of this International Standard, whereas Annex K is informative. ISO 2015

25、 All rights reserved vBS ISO 15016:2015ISO 15016:2015(E)IntroductionThis International Standard concerns the method of analysing the results obtained from speed trials.The primary purpose of speed and power trials is to determine a ships performance in terms of ships speed, power and propeller shaft

26、 speed under prescribed ships conditions and thereby verify the satisfactory attainment of a ships speed stipulated by Energy Efficiency Design Index (EEDI) regulations and/or contract. Ships speed is that realized under conditions stipulated by contract and/or EEDI regulations, which are usually; s

27、mooth hull and propeller surfaces, no wind, no waves, no current and deep water of 15C.In general it cannot be expected that all such stipulated conditions will be met during the actual trials. In practice, certain corrections for the environmental conditions have to be considered, such as for water

28、 depth, wind, waves and current12.The purpose of this International Standard is to define the basic requirements for the performance of speed trials, and provide procedures for evaluation and correction of speed trial data, covering all influences which may be relevant to the individual trial runs b

29、ased on sound scientific grounds, thereby enabling owners and others to have confidence in the validity of the final results.This International Standard is intended to help the interested parties achieve the desired target accuracy of, within 2 % in shaft power and 0,1 kn in speed.The procedure spec

30、ified in this International Standard has been developed largely on the basis of published data on speed trials and on ships performance, the more important among them being listed in Clause 2.ISO has invited the International Towing Tank Conference (ITTC) to co-operate on the development of a new st

31、andard for speed/power trials taking into account the new guidelines issued by ITTC and approved by MEPC65 for EEDI. The contribution of the STA-group and the ITTC is highly appreciated.Substitution of terms clauseThis International Standard is generally applied to those ships for which survey and c

32、ertification of EEDI is required under International Maritime Organization (IMO) Resolution MEPC.214(63) as amended by MEPC.234(65). In the case of other ships, to which the above IMO resolutions are not applicable, the terms or phrases of this International Standard are deemed to be replaced as nec

33、essary (e.g. “agreement between the Shipbuilder, the Owner and the Verifier” shall be read as “agreement between the Shipbuilder and the Owner” etc.)vi ISO 2015 All rights reservedBS ISO 15016:2015Ships and marine technology Guidelines for the assessment of speed and power performance by analysis of

34、 speed trial data1 ScopeThe primary purpose of speed and power trials is to determine a ships performance in terms of ships speed, power and propeller shaft speed under prescribed ships conditions and thereby verify the satisfactory attainment of a ships speed stipulated by EEDI regulations and/or c

35、ontract.This International Standard defines and specifies the following procedures to be applied in the preparation, execution, analysis and reporting of speed trials for ships, with reference to the effects which may have an influence upon the speed, power and propeller shaft speed relationship: th

36、e responsibility of each party involved, the trial preparations, the ships condition, the limiting weather and sea conditions, the trial procedure, the execution of the trial, the measurements required, the data acquisition and recording, the procedures for the evaluation and correction, the process

37、ing of the results.The contracted ships speed and the ships speed for EEDI are determined for stipulated conditions and at specific draughts (contract draught and/or EEDI draught). For EEDI, the environmental conditions are: no wind, no waves, no current and deep water of 15C.Normally, such stipulat

38、ed conditions are unlikely to be experienced in part or in full during the actual trials. In practice, certain corrections for the environmental conditions such as water depth, surface wind, waves, current and deviating ship draught, have to be considered. For this purpose, during the speed and powe

39、r trials, not only are shaft power and ships speed measured, but also relevant ship data and environmental conditions.The applicability of this International Standard is limited to ships of the displacement type.In this International Standard, it was decided that the unit to express the amount of an

40、 angle should be “rad” (radian) and that the unit of speed should be “m/s” (metres per second). Nevertheless, “” (degree) as a unit for an angle and “knots” as a unit for speed may be used. However, the units for the angles and speeds which appear in calculation formulas are to be “rad” and “m/s” wi

41、thout exception. Moreover, for the convenience of the users of this International Standard, numerical values using the units of degree and knots are stated jointly at appropriate places.If it is physically impossible to meet the conditions in this International Standard, a practical treatment is all

42、owed based on the documented mutual agreement among the Owner, the Verifier and the Shipbuilder.INTERNATIONAL STANDARD ISO 15016:2015(E) ISO 2015 All rights reserved 1BS ISO 15016:2015ISO 15016:2015(E)2 Normative referencesThe following documents, in whole or in part, are normatively referenced in t

43、his document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ITTC 7.5-04-01-01.4:2002, ITTC Recommended Procedures and Guidelines, Speed and Power

44、 Trials, Part 4: Instrumentation Installation and CalibrationITTC 7.5-02-07-02.2, ITTC Recommended Procedures and Guidelines, Prediction of Power Increase in Irregular Waves from Model Test3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1brake po

45、werpower delivered by the output coupling of the propulsion machinery before passing through any speed-reducing and transmission devices3.2contract powerbrake power or shaft power that is stipulated in the new build or conversion contract between the Shipbuilder and the Owner3.3contract speedships s

46、peed to be achieved as agreed within the terms of the new build/conversion contract3.4Double Runtwo consecutive speed runs at the same power setting on reciprocal headingsNote 1 to entry: See 3.16 for speed runs.3.5EEDIEnergy Efficiency Design Index as formulated by IMO3.6EEDI powerbrake power that

47、is stipulated by the Energy Efficiency Design Index (EEDI) regulations3.7EEDI Speedships speed achieved under the conditions specified by the IMO Resolution MEPC.245(66) (as amended)3.8ideal conditionsideal weather and sea conditions: no wind, no waves, no current and deep water of 15C3.9measured sh

48、ips speedships speed during a speed run derived from the headway distance between start and end position and the elapsed time of the speed run3.10Ownerparty that signed the new building or conversion contract with the Shipbuilder2 ISO 2015 All rights reservedBS ISO 15016:2015ISO 15016:2015(E)3.11pow

49、er settingsetting of engine throttle and propeller shaft speed for fixed pitch propellers and setting of the pitch angle for controllable pitch propellers3.12propeller pitchdesign pitch for a fixed pitch propeller3.13pitch angleoperating pitch angle of a Controllable Pitch Propeller (CPP)3.14shaft powernet power supplied by the propulsion machinery to the propulsion shafting after passing through all speed-reducing and other devices and after power for all attached auxiliaries has been taken off and acc