BS ISO 13041-3-2009 Test conditions for numerically controlled turning machines and turning centres - Geometric tests for machines with inverted vertical workholding spindles《数控车床和.pdf

《BS ISO 13041-3-2009 Test conditions for numerically controlled turning machines and turning centres - Geometric tests for machines with inverted vertical workholding spindles《数控车床和.pdf》由会员分享，可在线阅读，更多相关《BS ISO 13041-3-2009 Test conditions for numerically controlled turning machines and turning centres - Geometric tests for machines with inverted vertical workholding spindles《数控车床和.pdf（44页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO13041-3:2009ICS 25.040.20NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDTest conditions fornumerically controlledturning machines andturning centresPart 3: Geometric tests for machineswith inverted vertical workholdingspindlesThis British Standardwas publ

2、ished under theauthority of the StandardsPolicy and StrategyCommittee on 30 April2009 BSI 2009ISBN 978 0 580 56059 0Amendments/corrigenda issued since publicationDate CommentsBS ISO 13041-3:2009National forewordThis British Standard is the UK implementation of ISO 13041-3:2009.The UK participation i

3、n its preparation was entrusted to TechnicalCommittee MTE/1, Machine tools.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct ap

4、plication.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS ISO 13041-3:2009Reference numberISO 13041-3:2009(E)ISO 2009INTERNATIONAL STANDARD ISO13041-3First edition2009-03-01Test conditions for numerically controlled turning machines and turning centres Part 3: Geom

5、etric tests for machines with inverted vertical workholding spindles Conditions dessai des tours commande numrique et des centres de tournage Partie 3: Essais gomtriques pour les machines broches verticales inverses BS ISO 13041-3:2009ISO 13041-3:2009(E) PDF disclaimer This PDF file may contain embe

6、dded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of

7、not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters

8、were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights re

9、served. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requ

10、ester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedBS ISO 13041-3:2009ISO 13041-3:2009(E) ISO 2009 All rights reserved iiiContents Page Foreword iv

11、1 Scope 1 2 Normative references1 3 Terms and definitions .1 4 Preliminary remarks 2 4.1 Measuring units .2 4.2 Reference to ISO 230-1 and ISO 230-7 3 4.3 Machine levelling.3 4.4 Testing sequence 3 4.5 Tests to be performed.3 4.6 Measuring instruments .3 4.7 Diagrams 3 4.8 Software compensation 3 4.

12、9 Minimum tolerance3 4.10 Machine classifications, descriptions, terminology and designation of axes3 4.11 Turrets 8 4.12 Machine size categories .8 5 Geometric tests9 5.1 Workholding spindle(s).9 5.2 Relation between workholding spindle(s) and linear axes of motion11 5.3 Angular deviations of linea

13、r axis motion 14 5.4 Turret and power-driven tools20 5.5 Swivelling workholding spindle head .28 6 Tests for checking accuracy of axes of rotation29 6.1 Rotational accuracy of workholding spindle29 6.2 Rotational accuracy of tool spindle.31 Annex A (informative) Three-point measuring method.33 Bibli

14、ography35 BS ISO 13041-3:2009ISO 13041-3:2009(E) iv ISO 2009 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through

15、ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates

16、 closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards.

17、 Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this

18、document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 13041-3 was prepared by Technical Committee ISO/TC 39, Machine tools, Subcommittee SC 2, Test conditions for metal cutting machine tools. ISO 13041 consists of the follo

19、wing parts, under the general title Test conditions for numerically controlled turning machines and turning centres: Part 1: Geometric tests for machines with a horizontal workholding spindle Part 2: Geometric tests for machines with a vertical workholding spindle Part 3: Geometric tests for machine

20、s with inverted vertical workholding spindles Part 4: Accuracy and repeatability of positioning of linear and rotary axes Part 5: Accuracy of feeds, speeds and interpolations Part 6: Accuracy of a finished test piece Part 7: Evaluation of contouring performance in the coordinate planes Part 8: Evalu

21、ation of thermal distortions BS ISO 13041-3:2009INTERNATIONAL STANDARD ISO 13041-3:2009(E) ISO 2009 All rights reserved 1Test conditions for numerically controlled turning machines and turning centres Part 3: Geometric tests for machines with inverted vertical workholding spindles 1 Scope ISO 13041-

22、3:2008 specifies, with reference to ISO 230-1 and ISO 230-7, the geometric tests on general-purpose, numerically controlled (NC) turning machines and turning centres with inverted vertical workholding spindles, as well as the corresponding applicable tolerances. This part of ISO 13041 presents the d

23、ifferent concepts or configurations and common features of NC turning machines and turning centres with inverted vertical spindles. It also provides a terminology and designation of controlled axes. (See Figures 1, 2, 3 and 4.) This part of ISO 13041 deals only with the verification of the accuracy

24、of the machine. It does not apply to the operational testing of the machine (e.g. vibration, abnormal noise, stick-slip motion of components), nor to machine characteristics (e.g. speeds, feeds), as such checks are generally carried out before testing accuracy. 2 Normative references The following r

25、eferenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 230-1:1996, Test code for machine tools Part 1: Geometric ac

26、curacy of machines operating under no-load or finishing conditions ISO 230-7:2006, Test code for machine tools Part 7: Geometric accuracy of axes of rotation 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 turning machine machine tool in whic

27、h the principle movement is on the rotation of the workpiece against the stationary cutting tool(s) 3.2 manual control mode of operation where each movement of the machine is individually initiated and controlled by the operator BS ISO 13041-3:2009ISO 13041-3:2009(E) 2 ISO 2009 All rights reserved3.

28、3 numerical control NC computerized numerical control CNC automatic control of a process performed by a device that makes use of numerical data introduced while the operation is in progress ISO 2806:1994 3.4 manually controlled turning machine turning machine whose process steps for the machining ar

29、e controlled or started by an operator without support by an NC-machining program 3.5 numerically controlled turning machine NC turning machine turning machine that operates under numerical control (NC) or computerized numerical control (CNC) 3.6 turning centre NC turning machine equipped with power

30、-driven tool(s) and the capacity to orientate the work-holding spindle around its axis. NOTE It can include additional features such as automatic tool changing from a turret and/or magazine. 3.7 numerically controlled turning machine with inverted vertical workholding spindle NC turning machine with

31、 inverted vertical workholding spindle NC turning machine where the workpiece is mounted on an inverted vertical workholding spindle equipped with a workholding device at the lower end of the workholding spindle. NOTE For other types of vertical workholding spindle machine, see ISO 13041-2. 3.8 turn

32、ing centre with inverted vertical workholding spindle turning centre having an inverted vertical workholding spindle equipped with a workholding device at the lower end of the vertical workholding spindle. NOTE 1 It can include additional features such as automatic tool changing from a magazine or Y

33、-axis motion. NOTE 2 For other types of vertical workholding spindle turning centre, see ISO 13041-2. 4 Preliminary remarks 4.1 Measuring units In this part of ISO 13041, all linear dimensions, deviations and corresponding tolerances are expressed in millimetres, angular dimensions are expressed in

34、degrees, and angular deviations and the corresponding tolerances are expressed in ratios, but in some cases microradians or arcseconds may be used for clarification purposes. The equivalence of the following expressions should always be kept in mind: 0,010/1 000 = 10 106= 10 rad 2 arcsec BS ISO 1304

35、1-3:2009ISO 13041-3:2009(E) ISO 2009 All rights reserved 34.2 Reference to ISO 230-1 and ISO 230-7 For application of this part of ISO 13041, reference shall be made to ISO 230-1 or ISO 230-7, especially for the installation of the machine before testing, warming-up of spindles and other moving part

36、s, the description of measuring methods, and recommended accuracy of testing equipment. In the “Observations” block of tests described in Clauses 5 and 6, the instructions are preceded by a reference to the corresponding clause/subclause in ISO 230-1 and/or ISO 230-7 in cases where the test concerne

37、d is in compliance with their specifications. Tolerances are given for each geometric test (see G1 to G20). 4.3 Machine levelling Prior to conducting tests on a machine, the machine should be levelled according to the recommendations of the supplier/manufacturer (see ISO 230-1:1996, 3.11). 4.4 Testi

38、ng sequence The sequence in which the geometric tests are given in no way defines the practical order of testing. In order to make the mounting of instruments or gauging easier, tests may be performed in any order. 4.5 Tests to be performed When testing a machine, it is not always necessary or possi

39、ble to carry out all the tests given in this part of ISO 13041. When the tests are required for acceptance purposes, the choice of tests relating to the components and/or the properties of the machine of interest is at the discretion of the user, in agreement with the supplier/manufacturer. The test

40、s to be used are to be clearly stated when ordering a machine. A mere reference to this part of ISO 13041 for the acceptance tests, without specifying the tests to be carried out, and without agreement on the relevant expenses, cannot be considered as binding for any contracting party. 4.6 Measuring

41、 instruments The measuring instruments indicated in relation to the tests given in Clauses 5 and 6 are examples only. Other instruments measuring the same quantities and having at least the same measurement uncertainty and the same resolution may be used. Linear displacement sensors shall have a res

42、olution of 0,001 mm or better. 4.7 Diagrams For reasons of simplification, the figures in Clauses 5 and 6 of this part of ISO 13041 illustrate only one type of machine. 4.8 Software compensation When built-in software facilities are available for compensating geometric, positioning, contouring and t

43、hermal deviations, their use during these tests should be based on agreement between the user and the supplier/manufacturer. When the software compensation is used, this shall be stated in the test reports. 4.9 Minimum tolerance When the tolerance for a geometric test is established for a measuring

44、length different from that given in this part of ISO 13041 (see ISO 230-1:1996, 2.311), it shall be taken into consideration that the minimum value of tolerance is 0,005 mm. 4.10 Machine classifications, descriptions, terminology and designation of axes The machines considered in this part of ISO 13

45、041 are divided into three basic configurations, as shown in Figure 1. BS ISO 13041-3:2009ISO 13041-3:2009(E) 4 ISO 2009 All rights reservedThis type of machine tool may also be considered as a machining unit in an FMS (flexible manufacturing system). a) Basic configuration b) Workhead with B axis c

46、) Turret with Y axis Figure 1 Three machine configurations with one workhead and one turret BS ISO 13041-3:2009ISO 13041-3:2009(E) ISO 2009 All rights reserved 5For the component nomenclature, refer to Table 1. Figure 2 Example of inverted vertical turning machine BS ISO 13041-3:2009ISO 13041-3:2009

47、(E) 6 ISO 2009 All rights reservedFor the component nomenclature, refer to Table 1. Figure 3 Example of inverted vertical turning centre (turret head with Y-axis motion) BS ISO 13041-3:2009ISO 13041-3:2009(E) ISO 2009 All rights reserved 7For the component nomenclature, refer to Table 1. Figure 4 Ex

48、ample of inverted vertical turning centre (spindle with Y-axis motion) Table 1 Component nomenclature (see Figures 2, 3 and 4) Designation Item number English French German 1 base base Maschinenbett 2 column montant Maschninenstnder 3 cross rail traverse porte-chariot Querfhrung 4 carriage, X axis c

49、hariot, axe X Schlitten, X Achse 5 carriage, Y axis chariot, axe Y Schlitten, Y Achse 6 workholding spindle head stock slideway glissire de la poupe fixe de la broche Werkstckspindelkastenfhrung 7 workholding spindle head stock, Z axis poupe fixe de la broche, axe Z Werkstckspindelkasten, Z Achse8 workholding spindle broche porte-pice Werkstckspindel 9 turret head porte-tourelle Revolverkopf 10 turret tourelle Revolver 11 turret head carriage, Y axis chariot du porte-tourelle, ax