BS ISO 10110-17-2004 Optics and optical instruments - Preparation of drawings for optical elements and systems - Laser irradiation damage threshold《光学和光学仪器 光学元件和系统制图准备 激光辐射损害阈》.pdf

《BS ISO 10110-17-2004 Optics and optical instruments - Preparation of drawings for optical elements and systems - Laser irradiation damage threshold《光学和光学仪器 光学元件和系统制图准备 激光辐射损害阈》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 10110-17-2004 Optics and optical instruments - Preparation of drawings for optical elements and systems - Laser irradiation damage threshold《光学和光学仪器 光学元件和系统制图准备 激光辐射损害阈》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 10110-17:2004 Optics and photonics Preparation of drawings for optical elements and systems Part 17: Laser irradiation damage threshold ICS 01.100.20; 31.260; 37.020 BS ISO 10110-17:2004 This British Standard was published under the authority of the Standards Policy and S t r

2、 a t e g y C o m m i t t e e o n 1 June 2004 BSI 1 June 2004 ISBN 0 580 43828 7 National foreword This British Standard reproduces verbatim ISO 10110-17:2004 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Committee CPW/172, Optics an

3、d optical instruments, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Catalogue

4、under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct

5、application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informe

6、d; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii, a blank page, pages 1 to 4, an inside back cover and a back cover. The BSI copyright notice d

7、isplayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments Reference number ISO 10110-17:2004(E)INTERNATIONAL STANDARD ISO 10110-17 First edition 2004-03-01 Optics and photonics Preparation of drawings for optical elements and sy

8、stems Part 17: Laser irradiation damage threshold Optique et photonique Prparation des dessins pour lments et systmes optiques Partie 17: Seuil de dommage au rayonnement laser BSISO1011017:2004DPlcsid Fremia ihTs PDF file mya ctnoian emdebt dedyfepcaes. In ccacnadrow eitA hebods licnesilop gnic,y ti

9、hs file mirp eb yatnde iv roweb detu slahl ton ide ebtlnu deess teh typfecaes wihce era hml era deddebicsnede ti dna onstlalde t noeh comuptfrep reromign tide ehtin.g In wodlnidaot gnihs fil,e trapise atpecc tiereht nser ehnopsiiblity fo nto ifnriigngn Aebods licnesilop gnic.y ehT ISO tneClar Secrte

10、irata caceptl on siibality in this .aera Ai ebods a tedarmfo kra Aebod SystemI snctaropro.de teDials fo teh sfotwcudorp erats sut deo crtaee tihs PDF file cna f ebi dnuon tlareneG eh Ifnler oatit evt oeh file; tP ehDc-Frtaeino marapterew stpo ereimizde fro irptni.gn Evyre cera neeb sah takne tsne oe

11、ru taht teh file is siutlbae fosu re yb ISO memdob rebeis. In tlnu ehikletneve y ttah lborp aem lertait gno it is f,dnuo plsaee ifnrom ttneC ehlar Secterirata ta teh serddaig sleb nevwo. ISO 4002 All irthgs erse.devr lnUeto sswrehise specified, on trap fo this lbupictaion maeb y cudorperro de tuiliz

12、i den yna form ro na ybm ynae,s lecetrinoc ro mceinahcla, incliduntohp gcoiypodna gn micrfoilm, wittuoh repmissii now nritign from ietI rehSa Ot tsserdda eh ebolw or ISOs memreb i ydobn the cnuotfo yr ttseuqer ehe.r ISO cirypothg fofice saCe tsopale 65 eneG 1121-HC 02 av leT. 4 + 10 947 22 1 11 xaF0

13、 947 22 14 + 9 74 E-mial coirypthgis.o gro We bwww.is.o gro Pulbisdehi n Switlrez dnaii BSISO1011017:2004 iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is

14、normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part

15、in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to pre

16、pare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that

17、some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10110-17 was prepared by Technical Committee ISO/TC 172, Optics and photonics, Subcommittee SC 1, Fundamental standards. ISO 10110 consists

18、of the following parts, under the general title Optics and photonics Preparation of drawings for optical elements and systems: Part 1: General Part 2: Material imperfections Stress birefringence Part 3: Material imperfections Bubbles and inclusions Part 4: Material imperfections Inhomogeneity and st

19、riae Part 5: Surface form tolerances Part 6: Centring tolerances Part 7: Surface imperfection tolerances Part 8: Surface texture Part 9: Surface treatment and coating Part 10: Table representing data of optical elements and cemented assemblies Part 11: Non-toleranced data Part 12: Aspheric surfaces

20、Part 14: Wavefront deformation tolerance Part 17: Laser irradiation damage threshold BSISO1011017:2004INTENRATIONAL TSANDADR IS-01101 O71:(4002E)1Optics and photonics Preparation of drawings for optical elements and systems Part 17: Laser irradiation damage threshold 1 Scope ISO 10110 specifies the

21、presentation of design and functional requirements for optical elements in technical drawings used for manufacturing and inspection. This part of ISO 10110 specifies rules for the indication of the damage threshold from laser irradiation up to which optical surfaces shall not exhibit any damage as d

22、efined in ISO 11254-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO

23、 10110-5, Optics and optical instruments Preparation of drawings for optical elements and systems Part 5: Surface form tolerances ISO 10110-6, Optics and optical instruments Preparation of drawings for optical elements and systems Part 6: Centring tolerances ISO 10110-7, Optics and optical instrumen

24、ts Preparation of drawings for optical elements and systems Part 7: Surface imperfection tolerances ISO 10110-10:2003, Optics and photonics Preparation of drawings for optical elements and systems Part 10: Table representing data of optical elements and cemented assemblies ISO 11145, Optics and opti

25、cal instruments Lasers and laser-related equipment Vocabulary and symbols ISO 11254-1:2000, Lasers and laser-related equipment Determination of laser-induced damage threshold of optical surfaces Part 1: 1-on-1 test ISO 11254-2, Lasers and laser-related equipment Determination of laser-induced damage

26、 threshold of optical surfaces Part 2: S-on-1 test 3 Terms and definitions For the purposes of this document the terms and definitions given in ISO 11145, ISO 11254-1 and the following apply. BSISO1011017:20042 3.1 wavelength wavelength of the laser radiation 3.2 threshold highest quantity of laser

27、radiation incident upon the optical surface for which the extrapolated probability of damage is zero NOTE The quantity of laser radiation may be expressed in energy density H maxor power density E max . ISO 11254-1:2000 3.3 effective pulse duration efflaser pulse ratio of the total pulse energy to m

28、aximum pulse power ISO 11254-1:2000 3.4 threshold energy density H thpulsed laser irradiation energy density threshold, expressed in joules per square centimetre, above which damage may occur 3.5 threshold power density E thpulsed laser irradiation power density threshold, expressed in watts per squ

29、are centimetre, above which damage may occur 3.6 threshold linear power density F thcontinuous wave and long pulse laser irradiation linear power density threshold, expressed in watts per centimetre, above which damage may occur NOTE For laser damage considerations a long pulse is when the thermal t

30、ransit distance, (2 D eff ) 1/2 , where D is the thermal diffusivity, is in the order of the size of the test spot d T,eff . 4 Other test parameters Any other test parameters shall be in accordance with the relevant parts of ISO 11254. For certain optical elements it may be necessary to specify the

31、state and plane of polarization as well as the angle of incidence. 5 Specifications 5.1 General Specifications of laser irradiation damage threshold apply to the finished surfaces, particularly surface treatments and coatings. BSISO1011017:2004 35.2 Damage threshold for pulsed laser irradiation The

32、specification of a laser irradiation damage threshold, H thor E th , for an optical surface shall include the laser wavelength, , and the effective pulse duration, eff . 5.3 Damage threshold for long pulse and continuous wave (cw) laser irradiation The specification of a laser irradiation damage thr

33、eshold, F th , for an optical surface shall include the laser wavelength, , and the effective pulse duration, eff . In case of cw-irradiation specify the irradiation time. NOTE In case of cw-lasers (i.e. irradiation time longer than 0,25 s according to ISO 11145) the effective pulse duration is not

34、defined and the term “irradiation time” is used. 6 Indication The laser irradiation damage threshold shall be indicated on the technical drawing by a code number and the parameters specified in Clause 5. Additional requirements shall be covered by notes. The code number for the laser radiation thres

35、hold is 6. The indication shall have the following form: a) for pulsed laser irradiation: 6/H th ; ; effor 6/E th ; ; effb) for long pulse and cw laser irradiation: 6/F th ; ; eff . The units of H th , E th , F th , and effshall be given in the indication. 7 Location The indication on the technical

36、drawing shall be shown in connection with a leader line to the surface to which it relates and will be associated with other surface codes (3/, 4/, 5/) as specified in ISO 10110-5, ISO 10110-6 and ISO 10110-7. An example of such an indication is shown in Figure A.1 of ISO 10110-1:1996. Alternatively

37、, the indication may be listed in a table according to Figure 3 of ISO 10110-10:2003. 8 Examples of indication EXAMPLE 1: 6/25 Jcm 2 ; 1 064 nm; 20 ns This means that the damage threshold is above an energy density of 25 Jcm 2 , for a laser wavelength of 1 064 nm (Nd:YAG) and an effective pulse dura

38、tion of 20 ns. EXAMPLE 2: 6/10 kWcm 1 ; 10,6 m; 1 s This means that the damage threshold is above a linear power density of 10 kWcm 1for a cw laser emitting at 10,6 m wavelength (CO 2 ) and an irradiation time of 1 s. BSISO1011017:20044 Bibliography 1 ISO 10110-1:1996, Optics and optical instruments

39、 Preparation of drawings for optical elements and systems Part 1: General BSISO1011017:2004BS ISO 10110-17:2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on stan

40、dards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality

41、 of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20

42、 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0

43、)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwi

44、se requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and

45、 services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits con

46、tact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.b

47、si-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or tra

48、nsmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbs