BS ISO 10069-1-2008 Tools for pressing - Elastomer pressure springs - General specification《冲压工具 弹性体压缩弹簧 一般规范》.pdf

《BS ISO 10069-1-2008 Tools for pressing - Elastomer pressure springs - General specification《冲压工具 弹性体压缩弹簧 一般规范》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 10069-1-2008 Tools for pressing - Elastomer pressure springs - General specification《冲压工具 弹性体压缩弹簧 一般规范》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO10069-1:2008ICS 25.120.10NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDTools for pressing Elastomer pressurespringsPart 1: General specificationThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 3 2008 B

2、SI 2008ISBN 978 0 580 63239 6Amendments/corrigenda issued since publicationDate CommentsBS ISO 10069-1:2008National forewordThis British Standard is the UK implementation of ISO 10069-1:2008. Itsupersedes BS 7568-12:1992 which is withdrawn.The UK participation in its preparation was entrusted to Tec

3、hnicalCommittee MTE/12, Tools for pressing and moulding.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Complianc

4、e with a British Standard cannot confer immunityfrom legal obligations.0SeptemberBS ISO 10069-1:2008Reference numberISO 10069-1:2008(E)ISO 2008INTERNATIONAL STANDARD ISO10069-1Second edition2008-08-15Tools for pressing Elastomer pressure springs Part 1: General specification Outillage de presse Ress

5、orts de compression en lastomre Partie 1: Spcifications gnrales BS ISO 10069-1:2008ISO 10069-1:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are em

6、bedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporate

7、d. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a pr

8、oblem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, inc

9、luding photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Publi

10、shed in Switzerland ii ISO 2008 All rights reservedBS ISO 10069-1:2008ISO 10069-1:2008(E) ISO 2008 All rights reserved iiiContents Page Foreword iv 1 Scope . 1 2 Normative references . 1 3 Dimensions 2 4 Materials and their hardness . 6 5 Designation . 6 6 Marking 6 Annex A (informative) Examples of

11、 suitable applications . 7 Bibliography . 10 BS ISO 10069-1:2008ISO 10069-1:2008(E) iv ISO 2008 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standar

12、ds is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take

13、 part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is

14、to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility

15、 that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10069-1 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 8, Tools for pressing and moulding. This second ed

16、ition cancels and replaces the first edition (ISO 10069-1:1991), of which it constitutes a minor revision. In particular, the indication of surface textures has been updated in accordance with ISO 1302:2002. ISO 10069 consists of the following parts, under the general title Tools for pressing Elasto

17、mer pressure springs: Part 1: General specification Part 2: Specification of accessories BS ISO 10069-1:2008INTERNATIONAL STANDARD ISO 10069-1:2008(E) ISO 2008 All rights reserved 1Tools for pressing Elastomer pressure springs Part 1: General specification 1 Scope This part of ISO 10069 specifies th

18、e dimensions, in millimetres, of elastomer pressure springs intended for use in press tools, and the diameters, in millimetres, of counterbores for these pressure springs. It also gives information concerning materials and their hardness, and specifies the designation of springs that are in accordan

19、ce with its requirements, together with the marking of their packages. Examples of suitable applications are given in Annex A. Dimensions of accessories (spring collars and pilot pins) are specified in ISO 10069-2. 2 Normative references The following referenced documents are indispensable for the a

20、pplication of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 10069-2, Tools for pressing Elastomer pressure springs Part 2: Specification of accessories BS ISO 10069-1:

21、2008ISO 10069-1:2008(E) 2 ISO 2008 All rights reserved3 Dimensions 3.1 Elastomer pressure springs The dimensions of elastomer pressure springs shall be in accordance with Figure 1 and Tables 1 and 2. Key 1 contour of free pressure spring 2 contour of pressure spring in compression d1diameter of the

22、free pressure spring d2internal diameter of the pressure spring d3diameter of the pressure spring in compression l1length of the free pressure spring l2difference between the free and fully compressed lengths Figure 1 Pressure spring BS ISO 10069-1:2008ISO 10069-1:2008(E) ISO 2008 All rights reserve

23、d 3Table 1 General dimensions of elastomer pressure springs Dimensions in millimetres d3, maxfor l2, maxl1d1d2CR aPUR a16 20 25 32 40 50 63 80 100 125 160 16 6,5 21,6 20 20 8,5 27 25 25 10,5 33,8 31,3 32 43,2 40 40 13,5 54 50 50 67,5 62,5 63 17 85 78,8 80 108 100 100 21 135 125 125 27 168,8 156,3 aS

24、ee Clause 4 for an explanation of these abbreviated terms. BS ISO 10069-1:2008ISO 10069-1:2008(E) 4 ISO 2008 All rights reservedTable 2 Values of the load, F, and the difference between the free and fully compressed lengths, l2, for elastomer springs in accordance with this part of ISO 10069 Dimensi

25、ons in millimetres CR PUR CR PUR d1l1F max. kN l2amax. F max. kN l2bmax. d1l1F max.kN l2amax. F max. kN l2bmax. 16 5,6 4 32 11,2 8 20 7 5 40 14 10 16 25 0,3 8,75 1,2 6,25 50 17,5 12,5 16 5,6 4 63 22,05 15,75 20 7 5 80 28 20 25 8,75 6,25 100 35 25 20 32 0,5 11,2 2 8 63 125 10 43,75 21 31,25 20 7 5 32

26、 11,2 8 25 8,75 6,25 40 14 10 32 11,2 8 50 17,5 12,5 25 40 0,8 14 3,5 10 63 22,05 15,75 32 11,2 8 80 28 20 40 14 10 100 35 25 50 17,5 12,5 80 125 18 43,75 38 31,75 32 63 2,3 22,05 4,5 15,75 32 11,2 8 32 11,2 8 40 14 10 40 14 10 50 17,5 12,5 50 17,5 12,5 63 22,05 15,75 63 22,05 15,75 80 28 20 40 80 3

27、,6 28 8,5 20 100 35 25 32 11,2 8 100 125 27 43,75 65 31,75 40 14 10 32 11,2 8 50 17,5 12,5 40 14 10 63 22,05 15,75 50 17,5 12,5 80 28 20 63 22,05 15,75 50 100 5,5 35 13 25 80 28 20 100 35 25 125 43,75 31,75 125 160 42 56 100 40 al2, max= 0,35l1. bl2, max= 0,25l1. BS ISO 10069-1:2008ISO 10069-1:2008(

28、E) ISO 2008 All rights reserved 53.2 Counterbores for elastomer pressure springs The dimensions of counterbores for elastomer pressure springs shall be in accordance with Figures 2 a) and 2 b) and Table 3. Surface roughness values in micrometres a) b) Key d1diameter of the free pressure spring d3dia

29、meter of the pressure spring in compression d4diameter of the counterbore Figure 2 Elastomer pressure spring Table 3 Dimensions of the counterbores, d4, as a function of the diameters d1and d3 Dimensions in millimetres d424 30 38 48 61 75 94 118 150 188 d116 20 25 32 40 50 63 80 100 125 d322 27 34 4

30、3 54 68 85 108 135 169 BS ISO 10069-1:2008ISO 10069-1:2008(E) 6 ISO 2008 All rights reserved4 Materials and their hardness The material may be either an elastomer based on chloroprene rubber (CR) with a nominal hardness of 70 Shore A or an elastomer based on polyurethane rubber (PUR) with a nominal

31、hardness of 90 Shore A. Both these materials shall have a temperature resistance of up to approximately 80 C. 5 Designation An elastomer pressure spring in accordance with this part of ISO 10069 shall be designated as follows: a) “Elastomer pressure spring”; b) reference to this part of ISO 10069 (i

32、.e. ISO 10069-1); c) its diameter, d1; d) its length, l1; e) the material (CR or PUR). EXAMPLE An elastomer pressure spring made of an elastomer based on chloroprene rubber (CR), with a diameter, d1, of 16 mm and length, l1, of 20 mm, is designated as follows: Elastomer pressure spring ISO 10069-1 -

33、 16 20 - CR 6 Marking Elastomer pressure springs in accordance with this part of ISO 10069 shall be marked on the smallest packing unit with the following information: a) their diameter, d1; b) their length, l1; c) the material (CR or PUR). BS ISO 10069-1:2008ISO 10069-1:2008(E) ISO 2008 All rights

34、reserved 7Annex A (informative) Examples of suitable applications Examples of suitable applications are shown in Figures A.1 to A.3. a) Without spring collar b) With spring collar a d1u l1. bThe contact surface should be lubricated before mounting. It is recommended that only mineral oils or grease

35、be used for elastomer pressure springs made of polyurethane rubber (PUR). Figure A.1 Single elastomer pressure spring BS ISO 10069-1:2008ISO 10069-1:2008(E) 8 ISO 2008 All rights reserveda) Free b) In compression aThe contact surface should be lubricated before mounting. It is recommended that only

36、mineral oils or grease be used for elastomer pressure springs made of PUR. Figure A.2 Double elastomer pressure spring with one spring collar BS ISO 10069-1:2008ISO 10069-1:2008(E) ISO 2008 All rights reserved 9a) Free b) In compression aThe contact surface should be lubricated before mounting. It i

37、s recommended that only mineral oils or grease be used for elastomer pressure springs made of PUR. Figure A.3 Double elastomer pressure spring with three spring collars BS ISO 10069-1:2008ISO 10069-1:2008(E) 10 ISO 2008 All rights reservedBibliography 1 ISO 1302:2002, Geometrical Product Specificati

38、ons (GPS) Indication of surface texture in technical product documentation BS ISO 10069-1:2008BS ISO 10069-1:2008ISO 10069-1:2008(E) ICS 25.120.10 Price based on 10 pages ISO 2008 All rights reserved BS ISO 10069-1:2008This page has been intentionally left blank BS ISO10069-1:2008BSI GroupHeadquarte

39、rs 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Ro

40、yal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inacc

41、uracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which en

42、suresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit

43、/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on n

44、ational, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048

45、 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regard

46、ing online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardizati

47、on bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for