BS EN ISO 8130-3-2010 Coating powders Determination of density by liquid displacement pyknometer《涂覆粉末 浮子式液体比重瓶测定密度》.pdf

《BS EN ISO 8130-3-2010 Coating powders Determination of density by liquid displacement pyknometer《涂覆粉末 浮子式液体比重瓶测定密度》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 8130-3-2010 Coating powders Determination of density by liquid displacement pyknometer《涂覆粉末 浮子式液体比重瓶测定密度》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN ISO8130-3:2010Coating powders Part 3: Determination of density by liquid displacement pyknometer ICS 87.040Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/06/2011 08:44, Uncontrolled Copy, (c) BSINational forewordThis British Standard is the UK implementation of EN IS

2、O 8130-3:2010. It is identical to ISO 8130-3:1992. It supersedes BS 3900 J7:1993, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee STI/10, Test methods for paints.A list of organizations represented on this committee can be obtained on request to its se

3、cretary.This publication does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.BS EN ISO 8130-3:2010This British Standard, having

4、been prepared under the direction of the Pigments, Paints and Varnishes Standards Policy Committee, was published under the authority of the Standards Board and coms into effect on 15 April 1993 BSI 2011The following BSI references relate to the work on this standard: Committee reference PVC/10 Draf

5、t for comment 87/54851 DCAmendments/corrigenda issued since publicationDate Comments 28 February 2011 This corrigendum renumbers BS 3900-J7:1993 as BS EN ISO 8130-3:2010ISBN 978 0 580 22111 3-Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/06/2011 08:44, Uncontrolled Copy, (c) BSIEUROPEAN

6、STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 8130-3 November 2010 ICS 87.040 English Version Coating powders - Part 3: Determination of density by liquid displacement pyknometer (ISO 8130-3:1992) Poudres pour revtement - Partie 3: Dtermination de la masse volumique laide dun pycnomtre dplacement

7、de liquide (ISO 8130-3:1992) Pulverlacke - Teil 3: Bestimmung der Dichte mit einem Pyknometer durch Flssigkeitsverdrngung (ISO 8130-3:1992) This European Standard was approved by CEN on 16 October 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the con

8、ditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in th

9、ree official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of

10、 Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

11、 EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 8130-3:2010: ELicen

12、sed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/06/2011 08:44, Uncontrolled Copy, (c) BSIForeword The text of ISO 8130-3:1992 has been prepared by Technical Committee ISO/TC 35 “Paints and varnishes” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 8

13、130-3:2010 by Technical Committee CEN/TC 139 “Paints and varnishes” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2011, and conflicting national stan

14、dards shall be withdrawn at the latest by May 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Inter

15、nal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxemb

16、ourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 8130-3:1992 has been approved by CEN as a EN ISO 8130-3:2010 without any modification. BS EN ISO8130-3:2010EN ISO8130-3:2010 (E)Licen

17、sed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/06/2011 08:44, Uncontrolled Copy, (c) BSI BSI 2011 iiiContentsPageCommittees responsible Inside front coverNational foreword ii1 Scope 12 Normative references 13 Principle 14 Materials 15 Apparatus 16 Sampling 17 Procedure 18 Expression of results

18、 29 Test report 2List of references Inside back coverBS EN ISO8130-3:2010EN ISO 8130-3:2010 (E)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/06/2011 08:44, Uncontrolled Copy, (c) BSIThis page deliberately set blankLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/06/2011 08:44, U

19、ncontrolled Copy, (c) BSI BSI 2011 11 ScopeThis part of ISO 8130 specifies a liquid displacement pyknometer method for the determination of the density of coating powders. The method is based on a determination of the mass and the volume of a test portion.The apparatus specified is relatively inexpe

20、nsive, but the liquid displacement pyknometer method is liable to give erroneous results, particularly if the powder swells in contact with the displacement liquid used or the displacement liquid does not totally displace the air between the powder particles. The liquid displacement method is much s

21、lower in execution and less accurate than the gas comparison pyknometer method specified in ISO 8130-2 and is only to be used if it can be shown that the same results will be obtained as for the gas comparison pyknometer method.2 Normative referencesThe following standards contain provisions which,

22、through reference in this text, constitute provisions of this part of ISO 8130. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of ISO 8130 are encouraged to investigate the possibility of applying the

23、 most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards.ISO 787-10:1981, General methods of test for pigments and extenders Part 10: Determination of density Pyknometer method. ISO 842:1984, Raw materials for paints

24、 and varnishes Sampling. ISO 3696:1987, Water for analytical laboratory use Specification and test methods. ISO 8130-2:1992, Coating powders Part 2: Determination of density by gas comparison pyknometer (referee method). 3 PrincipleThe density of the coating powder is determined in a liquid displace

25、ment pyknometer in accordance with ISO 787-10, using a liquid that completely wets the product under test without swelling or dissolving it.4 Materials4.1 Water, of at least grade 3 purity as defined in ISO 3696, freshly boiled and cooled.4.2 Displacement liquid: any suitable aliphatic hydrocarbon o

26、r mixture of aliphatic hydrocarbons, free from aromatic compounds, with a boiling point within the range 80 C to 140 C.n-Heptane has been found to be suitable in many instances for the determination of the density of thermosetting coating powders. However, if there is an interaction between n-heptan

27、e and the product under test or its components, a suitable alternative liquid shall be used.4.3 Acetone, analytical grade.5 Apparatus5.1 Pyknometer, complying with ISO 787-10.5.2 Vacuum pump, with rubber pressure tube attachment.5.3 Balance, capacity 200 g, capable of weighing to 1 mg or less.6 Samp

28、lingTake a representative sample of the product to be tested, as described in ISO 842.7 ProcedureCarry out the determination in duplicate at (23 0,5) C. Weigh to the nearest 1 mg.7.1 Determination of the density of the displacement liquidWeigh the empty clean pyknometer (5.1), fill it to the mark wi

29、th the displacement liquid (4.2) and reweigh. Empty the pyknometer, wash it with three separate portions of acetone (4.3) and dry it under vacuum. Refill the pyknometer with water (4.1) and reweigh.Calculate the density 1, in grams per millilitre, of the displacement liquid at 23 C, using the equati

30、onwherem0is the mass, in grams, of the empty pyknometer;m1is the mass, in grams, of the pyknometer containing the displacement liquid;m2is the mass, in grams, of the pyknometer containing water;0is the density, in grams per millilitre, of the water. (For the purposes of this part of ISO 8130, take t

31、he density of water at 23 C as 0,998 g/ml.)1m1m0m2m0- - - - - - - - - - - - - - - - - - - - - - - - 0=BS EN ISO8130-3:2010EN ISO 8130-3:2010 (E)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/06/2011 08:44, Uncontrolled Copy, (c) BSI2 BSI 20117.2 Determination of the density of the coating

32、 powderEmpty the pyknometer, wash it with three separate portions of acetone and dry it under vacuum. Introduce a test portion of the sample of between 3 g and 4 g into the pyknometer and reweigh. Add sufficient displacement liquid to wet the test portion and just cover it. Attach the opening of the

33、 pyknometer to the pressure tube connected to the vacuum pump (5.2). Reduce the pressure in the pyknometer to a maximum of 1,2 kPa1)and shake until there is no further emission of air from the powder/liquid mixture. Carefully allow the pressure in the pyknometer to rise to atmospheric pressure. Then

34、 fill the pyknometer to the mark with displacement liquid, taking care not to disturb the sedimented powder. Take care also on filling in order to avoid powder remaining in the neck of the pyknometer. Reweigh the filled pyknometer.8 Expression of results8.1 CalculationCalculate the density p, in gra

35、ms per millilitre, of the coating powder at 23 C, using the equation:whereIf the two determinations differ by more than 0,04 g/ml, repeat the determination (7.2).Calculate the mean of two valid determinations and report the result to the nearest 0,01 g/ml.8.2 PrecisionOnly limited precision data are

36、 currently available. As a rule, a reproducibility of 0,05 g/ml can be expected.9 Test reportThe test report shall contain at least the following information:a) all details necessary to identify the product tested;b) a reference to this part of ISO 8130 (ISO 8130-3);c) the type of pyknometer and the

37、 displacement liquid used;d) the result of the test (individual values and mean value);e) any deviation from the test method specified;f) the date of the test.1) 100 kPa = 1 barm0is the mass, in grams, of the empty pyknometer;m1is the mass, in grams, of the pyknometer containing the displacement liq

38、uid;m3is the mass, in grams, of the pyknometer containing the test portion;m4is the mass, in grams, of the pyknometer containing the test portion and the displacement liquid;1is the density, in grams per millilitre, of the displacement liquid at 23 C.pm3m0m1m0()m4m3- - - - - - - - - - - - - - - - -

39、- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1=BS EN ISO8130-3:2010EN ISO 8130-3:2010 (E)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/06/2011 08:44, Uncontrolled Copy, (c) BSI BSI 2011List of referencesSee national foreword.BS EN ISO813

40、0-3:2010EN ISO 8130-3:2010 (E)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/06/2011 08:44, Uncontrolled Copy, (c) BSIBSI GroupHeadquarters 389 Chiswick High Road, London, W4 4AL, UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 standardsBSI - British Standards InstitutionBSI is the in

41、dependent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that th

42、ey possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the i

43、dentity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, internat

44、ional and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy t

45、o supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Vario

46、us BSI electronic information services are also available which give details on all its products and services. Contact Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developments and receive substantial disco

47、unts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standards Online can be found at http:/ information about

48、BSI is available on the BSI website at http:/ CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reprodu

49、ced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than i