BS EN ISO 6360-1-2004 Dentistry - Number coding system for rotary instruments - General characteristics《牙科学 旋转仪器的数字编码系统 一般特性》.pdf

《BS EN ISO 6360-1-2004 Dentistry - Number coding system for rotary instruments - General characteristics《牙科学 旋转仪器的数字编码系统 一般特性》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 6360-1-2004 Dentistry - Number coding system for rotary instruments - General characteristics《牙科学 旋转仪器的数字编码系统 一般特性》.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN ISO 6360-1:2004 Incorporating corrigendum September 2007 Dentistry Number coding system for rotary instruments Part 1: General characteristics ICS 11.060.25 BS EN ISO 6360-1:2004 This British Standard was published under the authority of the Standards Policy and Strategy Commi

2、ttee on 12 May 2004 BSI 2008 ISBN 978 0 580 60299 3 National foreword This British Standard is the UK implementation of EN ISO 6360-1:2004, incorporating corrigendum December 2007. It is identical with ISO 6360-1:2004, incorporating corrigendum September 2007. It supersedes BS 6828-5.1:1987 which is

3、 withdrawn. The UK participation in its preparation was entrusted by Technical Committee CH/106, Dentistry, to Subcommittee CH/106/4, Dental instruments. A list of organizations represented on this subcommittee can be obtained on request to its secretary. This publication does not purport to include

4、 all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since publication Date Comments 30 April 2008 Implementation of ISO corrigendum September 200

5、7 (subclause 5.5 revised) with CEN endorsement corrigendum December 2007EUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM ENISO63601 April2004 ICS11.060.25 SupersedesEN263601:1990 Englishversion DentistryNumbercodingsystemforrotaryinstrumentsPart 1:Generalcharacteristics(ISO63601:2004) ArtdentaireSystm

6、edecodificationnumriquepour instrumentsrotatifsPartie1:Caractristiquesgnrales (ISO63601:2004) ZahnheilkundeNummernsystemfrrotierende InstrumenteTeil1:AllgemeineGrundlagen(ISO6360 1:2004) ThisEuropeanStandardwasapprovedbyCENon1March2004. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulations

7、whichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheManagementCentreortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(Engl

8、ish,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheManagementCentrehasthesamestatusasthe official versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, G

9、ermany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Slovakia, Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36

10、B1050Brussels 2004CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.ENISO63601:2004E IncorporatingcorrigendumDecember2007INESO3606:12(400E) Foreword Thisdocument(ENISO63601:2004)hasbeenpreparedbyTechnicalCommitteeISO/TC106 “Dentistry“incollaborationwith

11、TechnicalCommitteeCEN/TC55“Dentistry“,thesecretariatof whichisheldbyDIN. ThisEuropeanStandardshallbegiventhestatusofanationalstandard,eitherbypublicationof anidenticaltextorbyendorsement,atthelatestbyOctober2004,andconflictingnational standardsshallbewithdrawnatthelatestbyOctober2004. Thisdocumentsu

12、persedesEN263601:1990. AccordingtotheCEN/CENELECInternalRegulations,thenationalstandardsorganizationsof thefollowingcountriesareboundtoimplementthisEuropeanStandard:Austria,Belgium, Cyprus,CzechRepublic,Denmark,Estonia,Finland,France,Germany,Greece,Hungary, Iceland,Ireland,Italy,Latvia,Lithuania,Lux

13、embourg,Malta,Netherlands,Norway,Poland, Portugal,Slovakia,Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. Endorsementnotice ThetextofISO63601:2004hasbeenapprovedbyCENasENISO63601:2004withoutany modifications._ _ BS EN ISO 6360-1:2004 Reference number ISO 6360-1:2004(E)INTERNATIONAL ADNATSDR ISO

14、6-0631 ceSond deition 2004-04-01 Dentistry Number coding system for rotary instruments Part 1: General characteristics Art dentaire Systme de codification numrique pour instruments rotatifs Partie 1: Caractristiques gnrales Referecne unbmer OSI 1-0636:002)E(4 OSI 4002INTERNATIONAL STANDARD ISO 6360-

15、1 Second edition 2004-04-01 sitneDrty uNc rebmidos gnmetsy rof ratory inemurts stn :1 traP reneGaarahc lctescitsir rAed tatnire ySstmed e cfidoicaitno munrqip euour snitruemstn sfitator raPtie :1 raCactrsiqitseu grnalse BS EN ISO 6360-1:2004DPlcsid Fremia ihTs PDF file mya ctnoian emdebt dedyfepcaes

16、. In ccacnadrow eitA hebods licnesilop gnic,y tihs file mirp eb yatnde iv roweb detu slahl ton ide ebtlnu deess teh typfecaes wihce era hml era deddebicsnede ti dna onstlalde t noeh comuptfrep reromign tide ehtin.g In wodlnidaot gnihs fil,e trapise atpecc tiereht nser ehnopsiiblity fo nto ifnriigngn

17、 Aebods licnesilop gnic.y ehT ISO tneClar Secrteirata caceptl on siibality in this .aera Ai ebods a tedarmfo kra Aebod SystemI snctaropro.de teDials fo teh sfotwcudorp erats sut deo crtaee tihs PDF file cna f ebi dnuon tlareneG eh Ifnler oatit evt oeh file; tP ehDc-Frtaeino marapterew stpo ereimizde

18、 fro irptni.gn Evyre cera neeb sah takne tsne oeru taht teh file is siutlbae fosu re yb ISO memdob rebeis. In tlnu ehikletneve y ttah lborp aem lertait gno it is f,dnuo plsaee ifnrom ttneC ehlar Secterirata ta teh serddaig sleb nevwo. ii iiiContents Page Foreword iv Introduction v 1 Scope 1 2 Normat

19、ive references . 1 3 Terms and definitions. 1 4 Number code . 2 5 Code numbers for general characteristics. 3 5.1 General. 3 5.2 Materials of the working part . 4 5.3 Coatings and bindings . 8 5.4 Types of shanks, handles or bore diameters (of unmounted instruments) . 10 5.5 Overall length 14 Annex

20、A (informative) Examples of identification numbers 16 Bibliography . 20 BS EN ISO 6360-1:2004iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carr

21、ied out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

22、ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare Internat

23、ional Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the e

24、lements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 6360-1 was prepared by Technical Committee ISO/TC 106, Dentistry, Subcommittee SC 4, Dental instruments. This second edition cancels and replaces the fir

25、st edition (ISO 6360-1:1985), which has been technically revised. It also incorporates the Amendment ISO 6360-1:1985/Add 1:1988. ISO 6360 consists of the following parts, under the general title Dentistry Number coding system for rotary instruments: Part 1: General characteristics Part 2: Shapes Par

26、t 3: Specific characteristics of burs and cutters Part 4: Specific characteristics of diamond instruments Part 6: Specific characteristics of abrasive instruments Part 7: Specific characteristics of mandrels and special instruments The following part is under preparation: Part 5: Specific characteri

27、stics of root-canal instruments BS EN ISO 6360-1:2004 vIntroduction This part of ISO 6360 is one of a series of International Standards relating to dental rotary instruments. A wide variety of dental rotary instruments, including root-canal instruments, is manufactured throughout the world for use b

28、y the dental profession. ISO 6360 provides a general number coding system for all types of dental rotary instruments, including accessories used in connection with these rotary instruments. The benefits of this system for dentistry in its entirety will only be derived if the system is widely adopted

29、; manufacturers of dental instruments, as well as the dental trade, are therefore requested to refer to ISO 6360 in their catalogues. This part of ISO 6360 was prepared in response to a need by the dental trade and industry and the dental profession for a universal system of classification and desig

30、nation for these instruments. It establishes a comprehensive number coding system suitable for all dental rotary instruments by use of a 15-digit code number identifying general and specific characteristics of instruments or groups of instruments. The first group of three digits identifies the mater

31、ials used for the working part of instruments. The second group of three digits identifies the shanks and handles used for instruments and the overall lengths of instruments. The third group of three digits identifies the shapes of instruments. The fourth group of three digits identifies the specifi

32、c characteristics for groups of instruments. The fifth group of three digits identifies the nominal diameter of the working part of the instruments, nominal size. The code numbers are generic code numbers. They do not provide exact product information. This information is given in the respective pro

33、duct standard for dental rotary instruments. For the application of the system and for the correct allocation of numbers or their identification, it is intended that the user consult this part of ISO 6360 and ISO 6360-2 for general information, and in addition one of the subsequent parts (ISO 6360-3

34、 to ISO 6360-7) for further information on specific characteristics of instruments or groups of instruments. For the allocation of new numbers complying with ISO 6360, an application supported by a description and a drawing should be sent to the secretariat of ISO/TC 106/SC 4, Dental instruments, wh

35、ich keeps updated records of all numbers currently allocated. An international group of experts will then decide on an appropriate identification number for the instrument in question, including its specific characteristics. The Secretary will inform the applicant, in due course, of the result and a

36、ssist him in using the number correctly. The Secretariat of ISO/TC 106/SC 4 can be contacted at: DIN NADENT Turnplatz 2 75172 Pforzheim Germany BS EN ISO 6360-1:2004blankINTENRATIONAL TSANDADR IS-0636 O1:(4002E)1Dentistry Number coding system for rotary instruments Part 1: General characteristics 1

37、Scope This part of ISO 6360 presents a number coding system for dental rotary instruments and accessories, and provides guidance with regard to its interpretation and use. This part of ISO 6360 specifies the code numbers for materials used for the working parts of instruments, the coating and the bi

38、nding of abrasives for instruments. This three-digit number forms the first group of three digits in the 15-digit overall number. This part of ISO 6360 further specifies the code numbers for shanks, handles, or bore diameter of unmounted instruments, and for the overall lengths of instruments. This

39、three-digit number forms the second group of three (two plus one) digits in the 15-digit overall number. In Annex A several examples of complete 15-digit identification numbers are given to demonstrate the number coding system, including examples of three (additional) optional digits (16 to 18) for

40、diamond instruments. NOTE In addition to terms for rotary instruments and accessories used in two of the three official ISO languages (English, French and Russian), this part of ISO 6360 gives the equivalent terms in the German language; these are published under the responsibility of the member bod

41、y for Germany (DIN). However, only the terms given in the official languages can be considered as ISO terms. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references,

42、 the latest edition of the referenced document (including any amendments) applies. ISO 1797-1, Dental rotary instruments Shanks Part 1: Shanks made of metals ISO 1797-2, Dental rotary instruments Shanks Part 2: Shanks made of plastics 3 Terms and definitions For the purposes of this document, the fo

43、llowing terms and definitions apply. 3.1 number coding system principle of setting up a number code for dental rotary instruments or their accessories 1 1 BS EN ISO 6360-1:20042 3.2 number code series of numbers specifically selected to provide in its entirety an overall number with relevant informa

44、tion for dental rotary instruments or their accessories 3.3 code number series of numbers for specific detail information for dental rotary instruments or their accessories NOTE The code number is part of the number code. 3.4 overall number complete number of 15 digits NOTE A sixth group of three di

45、gits may optionally be used for diamond instruments, to identify further specific characteristics (see ISO 6360-4). 3.5 identification number overall number for a definite instrument or accessory containing all relevant characteristics 4 Number code The number code consists of a 15-digit overall num

46、ber which specifies a) the material of working part, including grit size, coating, binding, b) the type of shank or handle, or bore diameter (for unmounted instruments), c) the overall length, or for root-canal instruments identification of the code, d) the shape of working part, e) the specific cha

47、racteristics for groups of instruments, f) the nominal size of working part. Three additional numbers may optionally be provided for diamond instruments (see ISO 6360-4). The optional numbers in the 16th to 18th locations are assigned provisionally for a period of five years. Then it shall be decided whether they should become full (required) numbers, stay as optional numbers, or be deleted. The complete number code describes only one type of instrument. For precise identification of an instrument, the complete number code, as indicated in the key to Figure 1, shall be used. If cert