BS EN ISO 15236-2-2017 Steel cord conveyor belts Preferred belt types《钢丝绳运输带 优选带类型》.pdf

《BS EN ISO 15236-2-2017 Steel cord conveyor belts Preferred belt types《钢丝绳运输带 优选带类型》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 15236-2-2017 Steel cord conveyor belts Preferred belt types《钢丝绳运输带 优选带类型》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO 15236-2:2017Steel cord conveyor beltsPart 2: Preferred belt types (ISO15236-2:2017)BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN ISO 15236-2:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 15236-2:2017.

2、 It supersedes BS EN ISO 15236-2:2004 which iswithdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/67, Conveyor belts.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include a

3、ll the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0 580 92942 7 ICS 53.040.20 Compliance with a British Standard cannot confer immunity from legal obligations.This Briti

4、sh Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2017.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 15236-2 January 2017 ICS 53.040.20 Supersedes EN ISO 1523

5、6-2:2004English Version Steel cord conveyor belts - Part 2: Preferred belt types (ISO 15236-2:2017) Courroies transporteuses cbles dacier - Partie 2: Types de courroies recommandes (ISO 15236-2:2017) Stahlseil-Frdergurte - Teil 2: Bevorzugte Gurttypen (ISO 15236-2:2017) This European Standard was ap

6、proved by CEN on 24 January 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such natio

7、nal standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own langua

8、ge and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,

9、Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORM

10、UNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 15236-2:2017 EBS EN ISO 15236-2:2017EN ISO 15236-2:2017 (E) 3 European foreword This document (EN ISO 152

11、36-2:2017) has been prepared by Technical Committee ISO/TC 41 “Pulleys and belts (including veebelts)” in collaboration with Technical Committee CEN/TC 188 “Conveyor belts” the secretariat of which is held by SNV. This European Standard shall be given the status of a national standard, either by pub

12、lication of an identical text or by endorsement, at the latest by July 2017, and conflicting national standards shall be withdrawn at the latest by July 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shal

13、l not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 15236-2:2004. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, B

14、ulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Swit

15、zerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 15236-2:2017 has been approved by CEN as EN ISO 15236-2:2017 without any modification. BS EN ISO 15236-2:2017ISO 15236-2:2017(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 Symbols

16、and units . 15 General remarks . 26 Belt types A . 27 Belt types B . 48 Belt types C . 5 ISO 2017 All rights reserved iiiContents PageBS EN ISO 15236-2:2017ISO 15236-2:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO

17、member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, govern

18、mental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenan

19、ce are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention

20、 is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and

21、/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity as

22、sessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.The committee responsible for this document is ISO/TC 41, Pulleys and belts (including veebelts), Subco

23、mmittee SC 3, Conveyor belts.This second edition cancels and replaces the first edition (ISO 15236-2:2004), which has been technically revised.A list of all the parts in the ISO 15236 series can be found on the ISO website.iv ISO 2017 All rights reservedBS EN ISO 15236-2:2017ISO 15236-2:2017(E)Intro

24、ductionSteel cord conveyor belts are mainly long belts which are manufactured by joining several delivery lengths on the site. To achieve joints with a high dynamic capability from belts supplied by various manufacturers, it is necessary to standardize some features, e.g. thickness of carcass or cor

25、d pitch and cord diameter. ISO 2017 All rights reserved vBS EN ISO 15236-2:2017BS EN ISO 15236-2:2017Steel cord conveyor belts Part 2: Preferred belt types1 ScopeThis document specifies preferred types of conveyor belts with steel cords in the longitudinal direction as reinforcement. The belt type s

26、eries in this document are based on the general requirements for construction given in ISO 15236-1.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the editi

27、on indicated applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 15236-1:2016, Steel cord conveyor belts Part 1: Design, dimensions and mechanical requirements for conveyor belts for general useISO 15236-4, Steel cord conveyor belts P

28、art 4: Vulcanized belt joints3 Terms and definitionsNo terms and definitions are listed in this document.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: avail

29、able at http:/www.iso.org/obp4 Symbols and unitsFor the purposes of this document, the symbols and the units given in Table 1 apply.Table 1 Symbols and unitsSymbol Explanation UnitB Belt width mmFbsBreaking strength of the cord taken from the cured belt kNKNNominal breaking strength per width of bel

30、t N/mmbKCalculated edge width mmd Cord diameter mmn Number of cords s Cover thickness mms6Carcass thickness mmINTERNATIONAL STANDARD ISO 15236-2:2017(E) ISO 2017 All rights reserved 1BS EN ISO 15236-2:2017ISO 15236-2:2017(E)Symbol Explanation Unitt Cord spacing/pitch mmminMinimum value maxMaximum va

31、lue 5 General remarksThe belt types described in this document are a selection out of the unlimited number of possible constructions; belts of the types A and B have been manufactured and installed in large quantities.It is the general conception of these belt types that belts of a certain nominal b

32、reaking strength have equal cords and cord pitches or at least equal thickness of the carcass.The requirements regarding belt design, i.e. cord diameter and cord pitch, depend on the mode of joint that will be applied. In accordance with ISO 15236-4, there are three types of vulcanized joints: inter

33、laced stepped joints; plain stepped joints; finger joints.For high performance stepped joints, it is essential that the belts to be joined have equal cord pitch and cord diameter. For belts to be joined by finger joints, the cord pitch and cord diameter are of less importance; what matters is a simi

34、lar thickness of the carcass. In Tables 2, 3, 4 and 5, therefore, cord diameter, cord pitch and number of cords are specified only for those types which are usually joined by stepped joints, i.e. belt types A1, A2 and B2.The cord numbers given in Tables 2, 3 and 5 are for guidance only. They result

35、from Formula (1):nKBFmin=Nbs1000(1)and from the requirement that the edge width shall be not larger than 40 mm and not smaller than 15 mm, i.e.15 bk 40A higher number of cords as well as a smaller number of cords can be applied provided that the requirements for minimum breaking strength specified i

36、n ISO 15236-1 and ISO 15236-4 are met. The belt breaking strengths are calculated by Formula (2):KFnBNbs=1000(2)For the purposes of this document, the symbols and units given in Table 1 apply.6 Belt types ABelt types A shall be manufactured with steel cords where the individual wires have been zinc

37、coated by a hot dip process. Requirements for belt types A1 and A2 shall be as given in Tables 2 and 3, respectively.NOTE Belt types A are designed for interlaced stepped belt joints with numbers of steps between 1 and 4. The t/d ratio of the A2 belt types is somewhat lower than that of the belt typ

38、es A1 resulting in thinner cords for comparable tensile strengths and in most cases a higher number of steps within the joint.Table 1 (continued)2 ISO 2017 All rights reservedBS EN ISO 15236-2:2017ISO 15236-2:2017(E)Table 2 Requirements for belt types A1Type of beltUnit 500 630 800 1 000 1 250 1 400

39、 1 600 1 800 2 000 2 250 2 500 2 800 3 150 3 500 4 000 4 500 5 000 5 400Min. breaking strength KN min.N/mm500 630 800 1 000 1 250 1 400 1 600 1 800 2 000 2 250 2 500 2 800 3 150 3 500 4 000 4 500 5 000 5 400Max. cord diameter dmax.mm 3,0 3,0 3,7 4,2 4,9 5,0 5,6 5,6 5,6 5,6 7,2 7,2 8,1 8,6 8,9 9,7 10

40、,9 11,3Min. breaking load of the cord Fbs min.kN 7,6 7,6 10,3 12,9 18,4 20,6 26,2 25,5 25,5 26,2 39,7 39,7 50,0 55,5 63,5 75,0 90,3 96,0Cord pitch, tmm 14,0 11,0 12,0 12,0 14,0 14,0 15,0 13,5 12,0 11,0 15,0 13,5 15,0 15,0 15,0 16,0 17,0 17,0Min. thickness of covers smin.mm 4,0 4,0 4,0 4,0 4,0 4,0 4,

41、0 4,0 4,0 4,0 5,0 5,0 5,5 6,0 6,5 7,0 7, 5 8,0Belt width B in mmTole- rance in mmNumber of cords, n500 +10/-5 33 42 39 39 34 34 31 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A650 +10/-7 44 54 51 51 45 45 41 46 52 56 41 46 41 41 41 39 36 N/A800 +10/-854 68 64 63 55 55 50 57 64 69 51 57 51 51 51 48 45

42、451 000 10 68 84 80 80 68 68 63 71 80 86 63 71 63 64 63 60 56 571 200 10 84 107 97 97 82 82 76 85 96 104 76 85 76 76 76 72 67 681 400 12 96 124 114 113 97 97 90 100 112 122 89 99 89 89 89 84 79 791 600 12 111 142 130 130 111 111 103 114 129 140 102 114 102 102 102 96 90 901 800 14 125 160 147 147 12

43、5 125 116 129 145 159 116 128 116 116 116 108 102 1022 000 14 139 177 164 163 140 139 130 144 162 177 129 143 129 129 129 121 114 1142 200 15 153 195 180 180 154 154 143 159 179 195 142 158 142 142 142 133 126 1262 400 15 167 213 197 197 168 168 156 174 195 213 156 173 156 156 156 146 137 1372 600 1

44、5 181 231 214 213 182 182 170 189 212 231 169 188 169 169 169 158 149 1492 800 15 196 249 230 230 197 197 183 203 229 249 182 202 182 182 182 171 161 1613 000 15 210 267 247 247 211 211 196 218 245 268 196 217 196 196 196 183 173 1733 200 15 224 286 264 263 225 225 210 233 262 286 209 232 209 209 20

45、9 196 184 184N/A = Not applicable because of troughability. ISO 2017 All rights reserved 3BS EN ISO 15236-2:2017ISO 15236-2:2017(E)Table 3 Requirements for belt types A2Type of belt Unit 1 000 1 250 1 400 1 600 1 800 2 000 2 250 2 500 2 800 3 150 3 500Min. breaking strength KN min.N/mm 1 000 1 250 1

46、 400 1 600 1 800 2 000 2 250 2 500 2 800 3 150 3 500Max. cord diameter dmax.mm 3,7 4,2 4,4 4,7 4,9 5,2 5,6 5,8 6,7 7, 2 7,4Min. breaking load of the cord Fbs min.kN 10,7 13,3 14,9 17,1 19,2 21,3 24,0 26,6 35,9 40,4 44,9Cord pitch, t mm 10,0 10,0 10,0 10,0 10,0 10,0 10,0 10,0 12,0 12,0 12,0Min. thick

47、ness of covers smin.mm 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 5,0 5,0 6,0Belt width B in mmToler-ance in mmNumber of cords, n500 +10/-5 47 47 47 47 47 47 47 47 39 39 39650 +10/-7 61 62 62 61 61 62 61 62 51 51 51800 +10/-8 76 76 76 75 76 76 76 76 63 63 631 000 10 96 96 96 95 95 95 94 94 78 78 781 200 10 116

48、 116 116 115 115 115 114 114 94 94 941 400 12 136 136 136 135 135 135 134 134 111 111 1111 600 12 156 156 156 155 155 155 154 154 128 128 1281 800 14 176 176 176 175 175 175 174 174 144 144 1442 000 14 196 196 196 195 195 195 194 194 161 161 1612 200 15 216 216 216 215 215 215 214 214 178 178 1782 4

49、00 15 236 236 236 235 235 235 234 234 194 194 1942 600 15 256 256 256 255 255 255 254 254 211 211 2112 800 15 276 276 276 275 275 275 274 274 228 228 2283 000 15 296 296 296 295 295 295 294 294 244 244 2443 200 15 316 316 316 315 315 315 314 314 261 261 2617 Belt types BCompared with the belt types A, belt types B are built with transverse reinforcements as indicated in ISO 15236-1:2016, 5.2.Belt types B are divided into two categories: belt types B1 with relatively high elongation “warp” cords; belt