BS EN ISO 14116-2015 Protective clothing Protection against flame Limited flame spread materials material assemblies and clothing《防护服 防火 限制火焰蔓延的材料、材料组件和衣服》.pdf

《BS EN ISO 14116-2015 Protective clothing Protection against flame Limited flame spread materials material assemblies and clothing《防护服 防火 限制火焰蔓延的材料、材料组件和衣服》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 14116-2015 Protective clothing Protection against flame Limited flame spread materials material assemblies and clothing《防护服 防火 限制火焰蔓延的材料、材料组件和衣服》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN ISO 14116:2015Protective clothing Protection against flame Limited flame spread materials,material assemblies andclothingBS EN ISO 14116:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO14116:2015. It supersedes BS EN ISO 14

2、116:2008 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PH/3/2, Heat and Flame Personal Protective Equipment.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include a

3、ll the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2015. Published by BSI StandardsLimited 2015ISBN 978 0 580 86811 5ICS 13.340.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British St

4、andard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2015.Amendments issued since publicationDate Text affectedBS EN ISO 14116:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 14116 July 2015 ICS 13.340.10 Supersedes EN ISO 14116:2008English V

5、ersion Protective clothing - Protection against flame - Limited flame spread materials, material assemblies and clothing (ISO 14116:2015) Vtements de protection - Protection contre les flammes - Matriaux, assemblages de matriaux et vtements propagation de flamme limite (ISO 14116:2015) Schutzkleidun

6、g - Schutz gegen Flammen - Materialien, Materialkombinationen und Kleidung mit begrenzter Flammenausbreitung (ISO 14116:2015) This European Standard was approved by CEN on 19 June 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for givin

7、g this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three offic

8、ial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of

9、Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, S

10、weden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for

11、 CEN national Members. Ref. No. EN ISO 14116:2015 EBS EN ISO 14116:2015EN ISO 14116:2015 (E) 2 Contents Page European foreword .3 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 89/686/EEC .4 BS EN ISO 14116:2015EN ISO 14116:2015 (E)

12、3 European foreword This document (EN ISO 14116:2015) has been prepared by Technical Committee ISO/TC 94 “Personal safety - Protective clothing and equipment“ in collaboration with Technical Committee CEN/TC 162 “Protective clothing including hand and arm protection and lifejackets” the secretariat

13、of which is held by DIN This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2016, and conflicting national standards shall be withdrawn at the latest by January 2016. Attention is drawn to the

14、 possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free T

15、rade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. This document supersedes EN ISO 14116:2008. According to the CEN-CENELEC Internal Regulations, the national standards

16、 organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxemb

17、ourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 14116:2015 has been approved by CEN as EN ISO 14116:2015 without any modification. BS EN ISO 14116:2015EN ISO 14116:2015 (E)

18、4 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 89/686/EEC This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide one means of conforming t

19、o Essential Requirements of the New Approach Directive 89/686/EEC on the approximation of the laws of the Member States relating to personal protective equipment. Once this standard is cited in the Official Journal of the European Union under that Directive and has been implemented as a national sta

20、ndard in at least one Member State, compliance with the normative clauses of this International Standard given in Table ZA.1 confers, within the limits of the scope of this International Standard, a presumption of conformity with the corresponding Essential Requirements of that Directive and associa

21、ted EFTA regulations. Table ZA. Correspondence between this International Standard and Directive 89/686/EEC Clause(s)/sub-clause(s) of this European Standard Essential Requirements (ERs) of Directive 89/686/EEC, Annex II Qualifying remarks 4.1, 4.4, 4.5, , 6.3. 1.2.1 Absence of risks and other inher

22、ent nuisance factors 4.5. 1.3.1 Adaptation of PPE to user morphology 8, 9 1.4 Information supplied by the manufacturer 5.3 2.4 PPE subject to ageing 6.2 1.3.2 Lightness and design strength 6.1. 3.6.1 PPE constituent materials and other components 8 2.12 PPE bearing identification marks related to he

23、alth and safety WARNING: Other requirements and other EU Directives may be applicable to the products falling within the scope of this standard. BS EN ISO 14116:2015ISO 14116:2015(E)Foreword ivIntroduction vi1 Scope . 12 Normative references 13 Terms and definitions . 14 General and design requireme

24、nts 35 Sampling, pre-treatment, and ageing . 45.1 Sampling . 45.2 Pre-treatment of material 45.3 Ageing . 45.4 Conditioning 56 Performance requirements . 56.1 Limited flame spread performance . 56.2 Physical requirements 66.2.1 Tensile Strength 66.2.2 Tear strength . 66.2.3 Burst strength 66.2.4 Sea

25、m strength . 66.3 Dimensional change of textile materials . 77 Classification 77.1 Requirements for limited flame spread index 1 . 77.2 Requirements for limited flame spread index 2 . 77.3 Requirements for limited flame spread index 3 . 78 Marking 88.1 Final index . 88.2 Single-layer materials . 88.

26、3 Material assemblies 88.4 Garments 89 Information supplied by the manufacturer . 9Annex A (normative) Uncertainty of measurement 10Annex B (normative) Determination of property values for rating and classification .11Bibliography .12 ISO 2015 All rights reserved iiiContents PageBS EN ISO 14116:2015

27、ISO 14116:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subje

28、ct for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC

29、) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be no

30、ted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying

31、 any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of

32、 users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplem

33、entary informationThe committee responsible for this document is ISO/TC 94, Personal safety - Protective clothing and equipment, Subcommittee SC 13, and by Technical Committee CEN/TC 162, Protective clothing including hand and arm protection and lifejackets in collaboration.This second edition cance

34、ls and replaces the first edition (ISO 14116:2008), which has been technically revised to include the following changes: include test procedures for burst strength testing of woven materials; include new definition for determination of hole formation; modify clause in design requirements regarding g

35、arment overlaps; modify clause on sampling requirements; modify pre-treatment clause to include requirements for single use garments; modify clause for ageing due to washing (maximum number of cleaning procedures as indicated by the manufacturer); include new requirement for measuring property value

36、 for rating and classification; modify test procedure for the flame testing of labels, badges, and retro-reflective materials; include requirement and procedure for testing of hardware; include requirement and test procedure for burst strength testing of knitted materials; include requirement and te

37、st procedure for tensile strength testing of non-woven materials; include requirement and test procedure for tear strength testing of non-woven materials; modify requirement for tear strength of woven and non-woven materials; modify flame spread definition;iv ISO 2015 All rights reservedBS EN ISO 14

38、116:2015ISO 14116:2015(E) modify requirement for flaming debris; modify afterflame requirement for flame spread of Index 3 materials; modify afterglow requirement for flame spread of Index 1, Index 2, and Index 3 materials.; include statement for flame spread testing in regard to interlining materia

39、ls for Index 2 and Index 3 materials; include normative Annex for uncertainty of measurement; include normative Annex for measuring property value for rating and classification. ISO 2015 All rights reserved vBS EN ISO 14116:2015ISO 14116:2015(E)IntroductionThe purpose of this International Standard

40、is to provide minimum performance requirements for clothing in order to reduce the possibility of the clothing and/or its materials burning when in occasional and brief contact with small flames and thereby, itself constituting a hazard.For complete protection against exposure to flame, it will be n

41、ecessary to protect the head, face, hands, and/or feet with suitable PPE and, in some cases, appropriate respiratory protection might also be considered necessary.Attention is drawn to ISO/TR 2801:2007,5which sets out guidelines for selection, use, care, and maintenance of protective clothing agains

42、t flame.Nothing in this International Standard is intended to restrict any jurisdiction, purchaser, or manufacturer from exceeding these minimum requirements.vi ISO 2015 All rights reservedBS EN ISO 14116:2015INTERNATIONAL STANDARD ISO 14116:2015(E)Protective clothing Protection against flame Limite

43、d flame spread materials, material assemblies and clothing1 ScopeThis International Standard specifies the performance requirements for the limited flame spread properties of all materials, all material assemblies, and protective clothing in order to reduce the possibility of the clothing burning wh

44、en in occasional and brief contact with small flames and thereby constituting a hazard. Additional requirements for clothing are also specified, including design requirements, mechanical requirements, marking, and information supplied by the manufacturer.When protection against heat hazards is neces

45、sary, in addition to protection against flame, this International Standard is not appropriate. International Standards such as ISO 11612 are to be used instead.A classification system is given for materials, material assemblies, and garments which are tested according to ISO 15025, Procedure A.2 Nor

46、mative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments)

47、 applies.ISO 13934-1, Textiles Tensile properties of fabrics Part 1: Determination of maximum force and elongation at maximum force using the strip methodISO 13935-2, Textiles Seam tensile properties of fabrics and made-up textile articles Part 2: Determination of maximum force to seam rupture using

48、 the grab methodISO 13937-2, Textiles Tear properties of fabrics Part 2: Determination of tear force of trouser-shaped test specimens (Single tear method)ISO 13938-1, Textiles Bursting properties of fabrics Part 1: Hydraulic method for determination of bursting strength and bursting distensionISO 13

49、938-2, Textiles Bursting properties of fabrics Part 2: Pneumatic method for determination of bursting strength and bursting distensionISO 15025, Protective clothing Protection against heat and flame Method of test for limited flame spreadISO 13688, Protective clothing General requirementsISO 9073-4, Textiles Test methods for nonwovens Part 4: Determination of tear resistanceISO 5077, Textiles Determination of dimensional change in washing and drying3 Terms and definitionsFor the purposes of this doc