BS EN ISO 12570-2000+A1-2013 Hygrothermal performance of building materials and products Determination of moisture content by drying at elevated temperature《建筑材料和产品的湿热性能采用高温干燥法对水分含.pdf

《BS EN ISO 12570-2000+A1-2013 Hygrothermal performance of building materials and products Determination of moisture content by drying at elevated temperature《建筑材料和产品的湿热性能采用高温干燥法对水分含.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 12570-2000+A1-2013 Hygrothermal performance of building materials and products Determination of moisture content by drying at elevated temperature《建筑材料和产品的湿热性能采用高温干燥法对水分含.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、|BRITISH STANDARDBS EN ISO12570:2000The European Standard EN ISO 12570:2000 has the status of aBritish StandardICS 91.100.01NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWHygrothermalperformance of buildingmaterials andproductsDetermination ofmoisture content bydrying at eleva

2、tedtemperatureBS EN ISO 12570:2000 +A1:2013Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 12570:2000+A1:2013ISBN 978 0 580 77038 8Amendments/corrigenda issued since pu

3、blicationDate Comments30 June 2013 Implementation of ISO amendment 1:2013 with CEN endorsement A1:2013: Table 1 modifiedThis British Standard, having been prepared under the direction of the Sector Committee for Building and Civil Engineering, was published under the authority of the Standards Commi

4、ttee and comes into effect on 15 May 2000 The British Standards Institution 2013. Published by BSI Standards Limited 2013National forewordThis British Standard is the UK implementation of EN ISO 12570:2000+A1:2013. It is identical to ISO 12570:2000, incorporating amendment 1:2013. It supersedes BS E

5、N ISO 12570:2000, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee B/540, Energy performance of materials components and buildings.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does no

6、t purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo

7、reproduction or networking permitted without license from IHS-,-,-EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 12570March 2000ICS 91.100.01English versionHygrothermal performance of building materials and products -Determination of moisture content by drying at elevatedtemperature (ISO 1257

8、0:2000)Performance hygrothermique des matriaux et produitspour le btiment - Dtermination du taux dhumidit parschage chaud (ISO 12570:2000)Wrme- und feuchtetechnisches Verhalten von Baustoffenund Bauprodukten - Bestimmung des Feuchtegehaltesdurch Trocknen bei erhlter Temperatur (ISO 12570:2000)This E

9、uropean Standard was approved by CEN on 20 May 1999.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references conc

10、erning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own la

11、nguage and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, S

12、witzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCentral Secretariat: rue de Stassart, 36 B-1050 Brussels 2000 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No

13、. EN ISO 12570:2000 EEN ISO 12570:2000+A1June 2013Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 3EN ISO 12570:2000ForewordThe text of EN ISO 12570:2000 has been prepared b

14、y Technical Committee CEN/TC 89“Thermal performance of buildings and building components“, the secretariat of which is heldby SIS, in collaboration with Technical Committee ISO/TC 163 “Thermal insulation”.This European Standard shall be given the status of a national standard, either by publicationo

15、f an identical text or by endorsement, at the latest by September 2000, and conflictingnational standards shall be withdrawn at the latest by December 2001.According to the CEN/CENELEC Internal Regulations, the national standards organizationsof the following countries are bound to implement this Eu

16、ropean Standard: Austria, Belgium,Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the UnitedKingdom.This standard is one of a series of standards which specify test methods for the thermal an

17、dmoisture related properties of building materials and products.IntroductionThe moisture content of a material can be used for various purposes, such as- part of a test method for the moisture related behaviour of the material;- to characterize the materials state;- to compare the actual moisture co

18、ntent with a critical or safe moisture content or toassess the moisture distribution.The test specimens, number, size and preparation can be specified in the relevant productstandards for the different types of materials.Page 2BS EN ISO 12570:2000+A1:2013ISO 12570:2000+A1:2013Foreword to amendment A

19、1This document (EN ISO 12570:2000/A1:2013) has been prepared by Technical Committee ISO/TC 163 “Thermal performance and energy use in the built environment” in collaboration with Technical Committee CEN/TC 89 “Thermal performance of buildings and building components” the secretariat of which is held

20、 by SIS.This Amendment to the European Standard EN ISO 12570:2000 shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2013, and conflicting national standards shall be withdrawn at the latest by December 2013.Atten

21、tion is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights.According to the CEN-CENELEC Internal Regulations, the national standards organizations of t

22、he following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Nether

23、lands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.Endorsement noticeThe text of ISO 12570:2000/Amd 1:2013 has been approved by CEN as EN ISO 12570:2000/A1:2013 without any modification.Copyright European Committee for Standardizat

24、ion Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 2EN ISO 12570:2000ContentspageForeword 3Introduction 31 Scope 42 Normative references 43 Definitions, symbols and units 44 Principle 55 Apparatus 56 Test specimens 67 Pro

25、cedure 68 Calculation and expression of results 89 Accuracy of measurement 1010 Test report 10Annex A (informative) Bibliography 11Page 2EN ISO 12570:2000ContentspageForeword 3Introduction 31 Scope 42 Normative references 43 Definitions, symbols and units 44 Principle 55 Apparatus 56 Test specimens

26、67 Procedure 68 Calculation and expression of results 89 Accuracy of measurement 1010 Test report 10Annex A (informative) Bibliography 11Page 3BS EN ISO 12570:2000+A1:2013ISO 12570:2000+A1:2013455566779111112Copyright European Committee for Standardization Provided by IHS under license with CENNot f

27、or ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 3EN ISO 12570:2000ForewordThe text of EN ISO 12570:2000 has been prepared by Technical Committee CEN/TC 89“Thermal performance of buildings and building components“, the secretariat of which is heldby SIS, in collabor

28、ation with Technical Committee ISO/TC 163 “Thermal insulation”.This European Standard shall be given the status of a national standard, either by publicationof an identical text or by endorsement, at the latest by September 2000, and conflictingnational standards shall be withdrawn at the latest by

29、December 2001.According to the CEN/CENELEC Internal Regulations, the national standards organizationsof the following countries are bound to implement this European Standard: Austria, Belgium,Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,Luxembourg, Netherlands,

30、Norway, Portugal, Spain, Sweden, Switzerland and the UnitedKingdom.This standard is one of a series of standards which specify test methods for the thermal andmoisture related properties of building materials and products.IntroductionThe moisture content of a material can be used for various purpose

31、s, such as- part of a test method for the moisture related behaviour of the material;- to characterize the materials state;- to compare the actual moisture content with a critical or safe moisture content or toassess the moisture distribution.The test specimens, number, size and preparation can be s

32、pecified in the relevant productstandards for the different types of materials.Page 4BS EN ISO 12570:2000+A1:2013ISO 12570:2000+A1:2013Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS

33、-,-,-Page 4EN ISO 12570:20001 ScopeThis standard, which is applicable to porous water permeable materials, specifies a generalmethod for determining the free water content of building materials by drying at elevatedtemperature. The standard does not specify the method for sampling.2 Normative refere

34、ncesThis European Standard incorporates by dated or undated reference, provisions from otherpublications. These normative references are cited at the appropriate places in the text and thepublications are listed hereafter. For dated references, subsequent amendments to or revisionsof these publicati

35、ons apply to this European Standard only when incorporated in it byamendment or revision. For undated references the latest edition of the publication referred toapplies.EN ISO 9346 Thermal insulation - Mass transfer - Physical quantities and definitions(ISO 9346)3 Definitions, symbols and units3.1

36、DefinitionsFor the purposes of this standard, the definitions given in EN ISO 9346 and the followingapply.3.1.1 moisture content mass by massmass of evaporable water divided by mass of dry material3.1.2 moisture content volume by volumevolume of evaporable water divided by volume of dry material3.1.

37、3 moisture content mass by volumemass of evaporable water divided by volume of dry material3.1.4 dry densitymass per volume of dry materialPage 5BS EN ISO 12570:2000+A1:2013ISO 12570:2000+A1:2013Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo r

38、eproduction or networking permitted without license from IHS-,-,-Page 5EN ISO 12570:20003.2 Symbols and unitsSymbol Quantity Unitm mass of test specimen kgm0mass of dried test specimen kgu moisture content mass by mass kg/kgV volume of test specimen m3G01moisture content volume by volume m3/m3w mois

39、ture content mass by volume kg/m3G020dry density kg/m34 PrincipleThe moisture content is calculated from the mass of the test specimen before drying and themass after drying at elevated temperature.5 ApparatusThe test apparatus shall include:a) ventilated oven capable of maintaining the drying tempe

40、rature with accuracy specified intable 1 and a relative humidity of less than 10 %: in warm, humid climates or at low dryingtemperatures it can be necessary to provide a supply of dried air to achieve this relativehumidity;b) scale or balance capable of weighing test specimens with an uncertainty no

41、t greater than0,1 % of their mass;c) metal rule or metal tape graduated in millimetres and permitting reading to an accuracy of0,5 mm;d) callipers, or any other instrument, capable of reading the dimensions of test specimens to anaccuracy of 0,1 mm;e) desiccator.Page 6BS EN ISO 12570:2000+A1:2013ISO

42、 12570:2000+A1:2013Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 6EN ISO 12570:20006 Test specimens6.1 Dimensions and number of test specimensThe dimensions and number of

43、test specimens, chosen to be representative of the material,shall be specified.NOTE These can be found in the relevant product standard or any other applicabledocument or agreement.6.2 Preparation of test specimens6.2.1 When test specimens have to be taken from larger elements, cutting and drilling

44、shallnot significantly influence the moisture content.6.2.2 If the moisture content mass by volume, w, or volume by volume, G01, is to bedetermined, the test specimen surfaces shall be clean and sufficiently plane to enabledetermination of the volume to the accuracy specified in 7.2 or 7.3 as releva

45、nt. 6.2.3 If the sampling is done in the field or when the drying cannot follow immediately afterthe cutting of the test specimens, the test specimens shall be packed in vapour-tight metalcontainers or wrapped in two layers of low permeability film or foil of vapour resistance atleast 200 MNs/g or s

46、dat least 1000 m (e.g. polyethylene foil of minimum thickness 0,2 mm)and sealed in order to avoid any change in moisture content before drying. When sampling inrain or after immersion, dry the surface of the specimen with a wrung out damp sponge.Care shall be taken to mark the sample to ensure subse

47、quent identification.7 Procedure7.1 Test conditionsThe laboratory temperature during the test shall be (23 6) G01C.7.2 Procedure for test specimens weighed immediately after cutting from sampleBefore drying, weigh the test specimens with an accuracy of 0,1 % of their mass. If thedetermination of the

48、 moisture content mass by volume or volume by volume is required,measure the dimensions of the test specimen with a metal rule or a calliper, with the accuracystated in clause 5. The error in determining the volume of the test specimen shall not exceed1 %.Dry the specimens at the temperature specified in the relevant product standard to constantmass. If no temperature for drying is specified in any product standard, the value appropriateto the material type specified in table 1 shall be used.Page 7BS EN ISO 1