BS EN ISO 10360-5-2010 Geometrical product specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) CMMs using single and multiple stylus co.pdf

《BS EN ISO 10360-5-2010 Geometrical product specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) CMMs using single and multiple stylus co.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 10360-5-2010 Geometrical product specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) CMMs using single and multiple stylus co.pdf（42页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 10360-5:2010Geometrical productspecifications (GPS) Acceptance and reverificationtests for coordinate measuringmachines (CMM)Part 5: CMMs using single and multiplestylu

2、s contacting probing systems (ISO10360-5:2010)BS EN ISO 10360-5:2010 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO10360-5:2010. It supersedes BS EN ISO 10360-5:2001 and DD ISO/PAS12868:2009 which are withdrawn.The UK participation in its preparation was en

3、trusted to TechnicalCommittee TDW/4, Technical Product Realization.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication

4、. BSI 2010ISBN 978 0 580 57466 5ICS 17.040.30Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 November 2010.Amendments issued since publicationDate Text affected

5、EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 10360-5 September 2010 ICS 17.040.30 Supersedes EN ISO 10360-5:2000English Version Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 5: CMMs using single and multiple

6、stylus contacting probingsystems (ISO 10360-5:2010) Spcification gomtrique des produits (GPS) - Essais de rception et de vrification priodique des machines mesurer tridimensionnelles (MMT) - Partie 5: MMT utilisant des systmes de palpage stylet simple ou stylets multiples (ISO 10360-5:2010) Geometri

7、sche Produktspezifikation (GPS) - Annahmeprfung und Besttigungsprfung fr Koordinatenmessgerte (KMG) - Teil 5: Prfung der Antastabweichungen von KMG mit berhrendem Messkopfsystem (ISO 10360-5:2010) This European Standard was approved by CEN on 12 June 2010. CEN members are bound to comply with the CE

8、N/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or

9、to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official vers

10、ions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Sl

11、ovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN

12、 national Members. Ref. No. EN ISO 10360-5:2010: EBS EN ISO 10360-5:2010 EN ISO 10360-5:2010 (E) 3 Foreword The text of ISO 10360-5:2010 has been prepared by Technical Committee ISO/TC 213 “Dimensional and geometrical product specifications and verification” of the International Organization for Sta

13、ndardization (ISO) and has been taken over as EN ISO 10360-5:2010 by Technical Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publi

14、cation of an identical text or by endorsement, at the latest by March 2011, and conflicting national standards shall be withdrawn at the latest by March 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shal

15、l not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 10360-5:2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, B

16、ulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement not

17、ice The text of ISO 10360-5:2010 has been approved by CEN as a EN ISO 10360-5:2010 without any modification. BS EN ISO 10360-5:2010ISO 10360-5:2010(E) ISO 2010 All rights reserved iiiContents Page Foreword .v Introductionvi 1 Scope1 2 Normative references2 3 Terms and definitions .2 4 Symbols6 5 Req

18、uirements for metrological characteristics7 5.1 Single-stylus probing error 7 5.2 Single-stylus probing configuration8 5.3 Multi-stylus probing errors and values .8 5.4 Multi-stylus probing configurations 9 5.5 Styli .9 5.6 Environmental conditions 9 5.7 Operating conditions 9 6 Acceptance tests and

19、 reverification tests 10 6.1 General .10 6.2 Single-stylus probing configuration10 6.2.1 Application .10 6.2.2 Principle10 6.2.3 Measuring equipment .10 6.2.4 Procedure.11 6.2.5 Derivation of test results 12 6.3 Fixed multi-probe and multi-stylus probing systems12 6.3.1 Principle12 6.3.2 Measuring e

20、quipment .13 6.3.3 Procedure.14 6.3.4 Data analysis15 6.4 Articulating probing systems.16 6.4.1 Principle16 6.4.2 Measuring equipment .17 6.4.3 Procedure.17 6.4.4 Data analysis19 7 Compliance with specification.19 7.1 Acceptance tests .19 7.2 Reverification tests .20 8 Applications .20 8.1 Acceptanc

21、e tests .20 8.2 Reverification tests .20 8.3 Interim checks .20 9 Indication in product documentation and data sheets21 Annex A (informative) Symbols and subscripts 23 Annex B (informative) Checking the probing system prior to the ISO 10360-2 test 24 Annex C (informative) Interpretation of multi-sty

22、lus test results.25 Annex D (normative) Maximum permissible error/limit figures.27 BS EN ISO 10360-5:2010ISO 10360-5:2010(E) iv ISO 2010 All rights reservedAnnex E (informative) Relation to the GPS matrix model .28 Bibliography 30 BS EN ISO 10360-5:2010ISO 10360-5:2010(E) ISO 2010 All rights reserve

23、d vForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which

24、a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matt

25、ers of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circul

26、ated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsib

27、le for identifying any or all such patent rights. ISO 10360-5 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product specifications and verification. This second edition cancels and replaces the first edition (ISO 10360-5:2000), which has been technically revised, and IS

28、O/PAS 12868:2009. ISO 10360 consists of the following parts, under the general title Geometrical Product Specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM): Part 1: Vocabulary Part 2: CMMs used for measuring linear dimensions Part 3: CMMs with the axis o

29、f a rotary table as the fourth axis Part 4: CMMs used in scanning measuring mode Part 5: CMMs using single and multiple stylus contacting probing systems Part 6: Estimation of errors in computing Gaussian associated features Part 7: CMMs equipped with video probing systems Part 9: CMMs with multiple

30、 probing systems The following parts are under preparation: Part 8: CMMs with optical distance sensors Part 10: Laser trackers for measuring point-to-point distances BS EN ISO 10360-5:2010ISO 10360-5:2010(E) vi ISO 2010 All rights reservedIntroduction This part of ISO 10360 is a geometrical product

31、specification (GPS) standard and is to be regarded as a general GPS standard (see ISO/TR 14638). It influences chain link 5 of the chains of standards of size, distance, radius, angle, form, orientation, location, run-out and datums. For more detailed information on the relation of this part of ISO

32、10360 to other standards and the GPS matrix model, see Annex E. The acceptance and reverification tests described in this part of ISO 10360 are applicable to coordinate measuring machines (CMMs) that use contacting probes, with or without multiple styli or multiple articulated-probe positions, when

33、measuring a workpiece. Experience has shown that the multi-stylus errors calculated using this part of ISO 10360 are significant and, at times, the dominant errors in the CMM. Owing to the virtually infinite variety of modern CMM probing system configurations, the tests specified by this part of ISO

34、 10360 have been limited to providing a testing format only. The tests are intended to provide information on the ability of a CMM to measure a feature or features, using a contacting probe and, when relevant, using multiple styli, multiple probes or multiple articulated-probe positions. The situati

35、ons to which they are applicable include single-stylus probing systems, multiple styli connected to the CMM probe (e.g. a star), installations using an articulating probing system (motorized or manual) that can be prequalified, installations using a repeatable probe-changing system, installations us

36、ing a repeatable stylus-changing system, and multi-probe installations. It is believed that the procedures given in this part of ISO 10360 will be helpful in identifying CMM system uncertainty components for specific measurement tasks, and that the user will be able to reduce errors by removing cont

37、ributing elements such as long probe extensions and styli, then retesting the new configuration set. The tests in this part of ISO 10360 are sensitive to many errors attributable to both the CMM and the probing system, and are to be performed in addition to the length-measuring tests given in ISO 10

38、360-2. The primary objective is to determine the practical performance of the complete CMM and probing system. Therefore, the tests are designed to reveal measuring errors which are likely to occur when such a combined system is used on real workpieces, e.g. errors generated by the interaction betwe

39、en large probe-tip-offset lengths and uncorrected CMM rotation errors. The errors found here differ from those found in the ELtests in ISO 10360-2:2009, 6.5, because with multiple styli the net CMM travel may be very different from the measured length. See Annex C for more information. BS EN ISO 103

40、60-5:2010INTERNATIONAL STANDARD ISO 10360-5:2010(E) ISO 2010 All rights reserved 1Geometrical product specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) Part 5: CMMs using single and multiple stylus contacting probing systems 1 Scope This part of ISO 103

41、60 specifies acceptance and periodic reverification tests of CMM performance with contacting probing systems and is only applicable to CMMs using any type of contacting probing system, a discrete point probing mode, and spherical or hemispherical stylus tip(s). It complements ISO 10360-7, which is t

42、he module for CMMs with video probing systems, and ISO 10360-2, which is universal, i.e. not probe-type specific. NOTE It is the CMM probing performance tests which are specified by the maximum permissible errors (MPEs), due to the impracticality of isolating the performance of the probing system fr

43、om that of the CMM, even on a small artefact such as a test sphere. This part of ISO 10360 applies to CMMs supplied with any of the following: a) single-stylus probing system; b) multi-stylus probing systems with fixed multiple styli attached to a single probe (e.g. “star” stylus); c) multiple probi

44、ng systems such as those with a stylus for each of their probes; d) systems with articulating probing; e) stylus and probe changing systems; f) manual (non-driven) CMMs. This part of ISO 10360 is not applicable to non-contacting probing systems, which require different testing procedures. The terms

45、“multi-stylus size error”, etc., should strictly be written “combined CMM and multi-stylus probing-system size error”, etc. For convenience, the wording has been truncated. If it is desired to isolate the probing-system performance as far as is practical, the influence of the CMM can be minimized. S

46、ee Annex C for more information. BS EN ISO 10360-5:2010ISO 10360-5:2010(E) 2 ISO 2010 All rights reserved2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the

47、 latest edition of the referenced document (including any amendments) applies. ISO 10360-1:2000, Geometrical Product Specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) Part 1: Vocabulary ISO 10360-2:2009, Geometrical Product Specifications (GPS) Acceptan

48、ce and reverification tests for coordinate measuring machines (CMM) Part 2: CMMs used for measuring linear dimensions ISO 14253-1, Geometrical Product Specifications (GPS) Inspection by measurement of workpieces and measuring equipment Part 1: Decision rules for proving conformance or non-conformanc

49、e with specifications ISO/IEC Guide 99, International vocabulary of metrology Basic and general concepts and associated terms (VIM) 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 10360-1, ISO 14253-1, ISO/IEC Guide 99 and the following apply. NOTE This clause contains eight definitions (3.6 to 3.13) which supersede fourteen similar definitions in Clause 9 of ISO 10360-1:2000. Some of these revised definitions are required to avoid