BS EN ISO 10360-2-2009 Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - CMMs used for measuring linear dimen.pdf

《BS EN ISO 10360-2-2009 Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - CMMs used for measuring linear dimen.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 10360-2-2009 Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - CMMs used for measuring linear dimen.pdf（38页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO10360-2:2009ICS 17.040.30NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDGeometrical productspecifications (GPS) Acceptance andreverification tests forcoordinate measuringmachines (CMM)Part 2: CMMs used for measuringlinear dimensions (ISO 10360-2:2009)L

2、icensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 31/03/2010 08:10, Uncontrolled Copy, (c) BSIThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 January2010 BSI 2010ISBN 978 0 580 57009 4Amendments/corrigenda issued since publicationDate Comm

3、entsBS EN ISO 10360-2:2009National forewordThis British Standard is the UK implementation of EN ISO10360-2:2009. It supersedes BS EN ISO 10360-2:2002 which iswithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee TDW/4, Technical Product Realization (TPR).A list of org

4、anizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligation

5、s.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 31/03/2010 08:10, Uncontrolled Copy, (c) BSIEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 10360-2 December 2009 ICS 17.040.30 Supersedes EN ISO 10360-2:2001English Version Geometrical product specifications (GPS) - Acceptance and re

6、verification tests for coordinate measuring machines (CMM) - Part 2: CMMs used for measuring linear dimensions (ISO 10360-2:2009) Spcification gomtrique des produits (GPS) - Essais de rception et de vrification priodique des machines mesurer tridimensionnelles (MMT) - Partie 2: MMT utilises pour les

7、 mesures de dimensions linaires (ISO 10360-2:2009) Geometrische Produktspezifikation (GPS) - Annahmeprfung und Besttigungsprfung fr Koordinatenmessgerte (KMG) - Teil 2: KMG angewendet fr Lngenmessungen (ISO 10360-2:2009) This European Standard was approved by CEN on 26 December 2008. CEN members are

8、 bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to t

9、he CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same

10、 status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Ro

11、mania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserve

12、d worldwide for CEN national Members. Ref. No. EN ISO 10360-2:2009: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 31/03/2010 08:10, Uncontrolled Copy, (c) BSIBS EN ISO 10360-2:2009EN ISO 10360-2:2009 (E) 3 Foreword This document (EN ISO 10360-2:2009) has been prepared by Technical Committe

13、e ISO/TC 213 “Dimensional and geometrical product specifications and verification“ in collaboration Technical Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a nat

14、ional standard, either by publication of an identical text or by endorsement, at the latest by June 2010, and conflicting national standards shall be withdrawn at the latest by June 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent ri

15、ghts. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 10360-2:2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European

16、Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United King

17、dom. Endorsement notice The text of ISO 10360-2:2009 has been approved by CEN as a EN ISO 10360-2:2009 without any modification. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 31/03/2010 08:10, Uncontrolled Copy, (c) BSIBS EN ISO 10360-2:2009ISO 10360-2:2009(E) ISO 2009 All rights reserved i

18、iiContents Page Foreword .v Introductionvi 1 Scope1 2 Normative references1 3 Terms and definitions .2 4 Symbols4 5 Environmental and metrological requirements4 5.1 Environmental conditions 4 5.2 Operating conditions 5 5.3 Length measurement error, EL.5 5.4 Repeatability range of the length measurem

19、ent error, R0.5 5.5 Workpiece loading effects5 6 Acceptance tests and reverification tests 6 6.1 General .6 6.2 Principle6 6.3 Length measurement error with zero ram axis stylus tip offset, E0.7 6.3.1 General .7 6.3.2 Measuring equipment .7 6.3.3 Procedure.8 6.3.4 Derivation of test results 9 6.4 Re

20、peatability range of the length measurement error, R0.9 6.5 Length measurement error with ram axis stylus tip offset of 150 mm, E150.10 6.5.1 Measuring equipment .10 6.5.2 Procedure.10 6.5.3 Derivation of test results 12 6.6 Dual ram CMMs12 6.6.1 Simplex operating mode.12 6.6.2 Duplex operating mode

21、.12 7 Compliance with specifications.13 7.1 Acceptance test .13 7.1.1 Acceptance criteria .13 7.1.2 Data rejection and repeated measurements.14 7.2 Reverification test .14 8 Applications .14 8.1 Acceptance test .14 8.2 Reverification test .15 8.3 Interim check .15 9 Indication in product documentati

22、on and data sheets15 Annex A (informative) Interim check.16 Annex B (normative) Artefacts that represent a calibrated test length.18 Annex C (informative) Alignment of gauges 23 Annex D (normative) Mathematical adjustments to low CTE artefacts.25 Annex E (informative) Location of the single stylus p

23、robing test .27 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 31/03/2010 08:10, Uncontrolled Copy, (c) BSIBS EN ISO 10360-2:2009ISO 10360-2:2009(E) iv ISO 2009 All rights reservedAnnex F (informative) Relation to the GPS matrix model .28 Bibliography 29 Licensed Copy: Wang Bin, ISO/EXCHANGE

24、 CHINA STANDARDS, 31/03/2010 08:10, Uncontrolled Copy, (c) BSIBS EN ISO 10360-2:2009ISO 10360-2:2009(E) ISO 2009 All rights reserved vForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing In

25、ternational Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison

26、with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of techn

27、ical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn

28、 to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10360-2 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product specifications and veri

29、fication. This third edition cancels and replaces the second edition (ISO 10360-2:2001), which has been technically revised. ISO 10360 consists of the following parts, under the general title Geometrical product specifications (GPS) Acceptance and reverification tests for coordinate measuring machin

30、es (CMM): Part 1: Vocabulary Part 2: CMMs used for measuring linear dimensions Part 3: CMMs with the axis of a rotary table as the fourth axis Part 4: CMMs used in scanning measuring mode Part 5: CMMs using single and multiple stylus contacting probing systems Part 6: Estimation of errors in computi

31、ng Gaussian associated features Part 7: CMMs equipped with imaging probing systems Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 31/03/2010 08:10, Uncontrolled Copy, (c) BSIBS EN ISO 10360-2:2009ISO 10360-2:2009(E) vi ISO 2009 All rights reservedIntroduction This part of ISO 10360 is a geom

32、etrical product specification (GPS) standard and is to be regarded as a general GPS standard (see ISO/TR 14638). It influences link 5 of the chains of standards on size, distance, radius, angle, form, orientation, location, run-out and datums. For more detailed information of the relation of this pa

33、rt of ISO 10360 to other standards and the GPS matrix model, see Annex F. The tests of this part of ISO 10360 have three technical objectives: 1) to test the error of indication of a calibrated test length using a probing system without any ram axis stylus tip offset; 2) to test the error of indicat

34、ion of a calibrated test length using a probing system with a specified ram axis stylus tip offset; and 3) to test the repeatability of measuring a calibrated test length. The benefits of these tests are that the measured result has a direct traceability to the unit length, the metre, and that it gi

35、ves information on how the CMM will perform on similar length measurements. Clause 3 of this part of ISO 10360 contains definitions that supersede similar definitions in ISO 10360-1:2000. The revised definitions are required to avoid an ambiguity that would otherwise have been introduced with this i

36、ssue of ISO 10360-2. Also, definition 3.6 supersedes effectively an identical definition in ISO 10360-1:2000 because the symbols used have been revised and expanded for clarification. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 31/03/2010 08:10, Uncontrolled Copy, (c) BSIBS EN ISO 10360-2

37、:2009INTERNATIONAL STANDARD ISO 10360-2:2009(E) ISO 2009 All rights reserved 1Geometrical product specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) Part 2: CMMs used for measuring linear dimensions 1 Scope This part of ISO 10360 specifies the acceptance

38、 tests for verifying the performance of a coordinate measuring machine (CMM) used for measuring linear dimensions as stated by the manufacturer. It also specifies the reverification tests that enable the user to periodically reverify the performance of the CMM. The acceptance and reverification test

39、s given in this part of ISO 10360 are applicable only to Cartesian CMMs using contacting probing systems of any type operating in the discrete-point probing mode. This part of ISO 10360 does not explicitly apply to: non-Cartesian CMMs; however, parties may apply this part of ISO 10360 to non-Cartesi

40、an CMMs by mutual agreement; CMMs using optical probing; however, parties may apply this approach to optical CMMs by mutual agreement. This part of ISO 10360 specifies performance requirements that can be assigned by the manufacturer or the user of a CMM, the manner of execution of the acceptance an

41、d reverification tests to demonstrate the stated requirements, rules for proving conformance, and applications for which the acceptance and reverification tests can be used. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated re

42、ferences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 10360-1:2000, Geometrical Product Specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) Part 1: Vocabular

43、y ISO 14253-1:1998, Geometrical Product Specifications (GPS) Inspection by measurement of workpieces and measuring equipment Part 1: Decision rules for proving conformance or non-conformance with specifications ISO 14660-1:1999, Geometrical Product Specifications (GPS) Geometrical features Part 1: G

44、eneral terms and definitions ISO/TS 23165:2006, Geometrical product specifications (GPS) Guidelines for the evaluation of coordinate measuring machine (CMM) test uncertainty ISO/IEC Guide 99, International vocabulary of metrology Basic and general concepts and associated terms (VIM) Licensed Copy: W

45、ang Bin, ISO/EXCHANGE CHINA STANDARDS, 31/03/2010 08:10, Uncontrolled Copy, (c) BSIBS EN ISO 10360-2:2009ISO 10360-2:2009(E) 2 ISO 2009 All rights reserved3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 10360-1, ISO 14253-1, ISO 14660-1, ISO/TS 23165

46、, ISO/IEC Guide 99 and the following apply. 3.1 ram axis stylus tip offset L distance (orthogonal to the ram axis) between the stylus tip and a reference point NOTE 1 The reference point is defined by the manufacturer. If no manufacturer-defined reference point is known, the user chooses a reference

47、 point close to the probe system mount. NOTE 2 The reference point is usually in or near the probe system. aL 0. Figure 1 Examples of the ram axis stylus tip offset in the case of an articulated probing system 3.2 coefficient of thermal expansion CTE linear thermal expansion coefficient of a materia

48、l at 20 C Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 31/03/2010 08:10, Uncontrolled Copy, (c) BSIBS EN ISO 10360-2:2009ISO 10360-2:2009(E) ISO 2009 All rights reserved 33.3 normal CTE material material with a CTE between 8 106/C and 13 106/C 3.4 length measurement error ELerror of indica

49、tion when measuring a calibrated test length using a CMM with a ram axis stylus tip offset of L, using a single probing point (or equivalent) at each end of the calibrated test length NOTE 1 In this part of ISO 10360, L = 0 mm and L = 150 mm (default values) are specified. NOTE 2 See Annex B for the requirements of point sampling strategies. 3.5 repeatability range of the length measurement error R0range (largest minus smallest) of three repeated length measurement errors measured by