BS EN ISO 4753-2011 Fasteners Ends of parts with external ISO metric thread《紧固件 有外部ISO公制螺纹的部件末端》.pdf

《BS EN ISO 4753-2011 Fasteners Ends of parts with external ISO metric thread《紧固件 有外部ISO公制螺纹的部件末端》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 4753-2011 Fasteners Ends of parts with external ISO metric thread《紧固件 有外部ISO公制螺纹的部件末端》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 4753:2011Fasteners Ends of parts withexternal ISO metric thread (ISO4753:2011)BS EN ISO 4753:2011 BRITISH STANDARDNational forewordThis British Standard is the UK imple

2、mentation of EN ISO 4753:2011.It supersedes BS EN ISO 4753:2000 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee FME/9/2, Fasteners - Reference Standards.A list of organizations represented on this committee can beobtained on request to its secretary.Thi

3、s publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 70330 0ICS 21.040.10; 21.060.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was publi

4、shed under the authority of theStandards Policy and Strategy Committee on 30 November 2011.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 4753 November 2011 ICS 21.060.01 Supersedes EN ISO 4753:1999English Version Fasteners - Ends of par

5、ts with external ISO metric thread (ISO 4753:2011) lments de fixation - Extrmits des lments filetage extrieur mtrique ISO (ISO 4753:2011) Mechanische Verbindungselemente - Enden von Teilen mit metrischem ISO-Auengewinde (ISO 4753:2011) This European Standard was approved by CEN on 31 October 2011. C

6、EN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on ap

7、plication to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC

8、Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Ne

9、therlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitati

10、on in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 4753:2011: EBS EN ISO 4753:2011EN ISO 4753:2011 (E) 3 Foreword This document (EN ISO 4753:2011) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC

11、185 “Fasteners” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2012, and conflicting national standards shall be withdrawn at the latest by May 2012.

12、Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 4753:1999. According to the CEN/CENELEC Internal Regul

13、ations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Mal

14、ta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 4753:2011 has been approved by CEN as a EN ISO 4753:2011 without any modification. BS EN ISO 4753:2011ISO 4753:2011(E) ISO 2011 All rights res

15、erved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for

16、which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on al

17、l matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are

18、circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held res

19、ponsible for identifying any or all such patent rights. ISO 4753 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 7, Reference standards. This third edition cancels and replaces the second edition (ISO 4753:1999), which has been technically revised. BS EN ISO 4753:2011BS EN I

20、SO 4753:2011INTERNATIONAL STANDARD ISO 4753:2011(E) ISO 2011 All rights reserved 1Fasteners Ends of parts with external ISO metric thread 1 Scope This International Standard specifies the form and dimensions of ends of parts with external ISO metric screw thread (e.g. bolt, screw and stud ends) reco

21、mmended for use. They apply to standardized or non-standardized threaded parts. For each end type, a symbol is specified and it is intended that these symbols be used when specifying one of the ends for threaded fasteners. 2 Normative references The following referenced documents are indispensable f

22、or the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions ISO 4027, Hexag

23、on socket set screws with cone point 3 Dimensions 3.1 General See Figures 1 and 2 and Tables 1 to 4. Symbols and descriptions of dimensions are specified in ISO 225. BS EN ISO 4753:2011ISO 4753:2011(E) 2 ISO 2011 All rights reserved3.2 Ends which are included in the nominal length of the fastener re

24、 1,4 d a) As-rolled end (RL) b) Chamfered end (CH) c) Rounded end (RN) d) Flat point (FL) e) Short dog point (SD) f) Long dog point (LD) g) Cone point (CN) h) Threaded cone point (CA) i) Truncated cone point (TC) Figure 1 BS EN ISO 4753:2011ISO 4753:2011(E) ISO 2011 All rights reserved 3dn d 1,6 P v

25、 0,5 d 0,5 mm lk 3 P ln 5 P ln lk 2 P j) Cup point (CP) k) Scrape point (SC) Key P pitch of the thread aEnd may be dimpled. bIncomplete thread u 2 P. cMaximum diameter at the minor thread diameter. dThe angle applies only to the portion of the point below the root diameter of the thread. eSlight rad

26、ius. f120 2 for short length screws; specified in product standard, e.g. ISO 4027. gThe end shall not be sharp to the touch. Figure 1 (continued) BS EN ISO 4753:2011ISO 4753:2011(E) 4 ISO 2011 All rights reservedTable 1 Dimensions Dimensions in millimetres Thread diameter dpdtcdzz1z2dah14bh16 h14 IT

27、140 dIT140 d1,6 0,8 0,8 0,40 0,80 1,8 0,9 0,9 0,45 0,902 1,0 1,0 0,50 1,00 2,2 1,2 1,1 0,55 1,102,5 1,5 1,2 0,63 1,25 3 2,0 1,4 0,75 1,503,5 2,2 1,7 0,88 1,75 4 2,5 2,0 1,00 2,004,5 3,0 2,2 1,12 2,25 5 3,5 2,5 1,25 2,506 4,0 1,5 3,0 1,50 3,00 7 5,0 2,0 4,0 1,75 3,508 5,5 2,0 5,0 2,00 4,00 10 7,0 2,5

28、 6,0 2,50 5,0012 8,5 3,0 8,0 3,00 6,00 14 10,0 4,0 8,5 3,50 7,0016 12,0 4,0 10,0 4,00 8,00 18 13,0 5,0 11,0 4,50 9,0020 15,0 5,0 14,0 5,00 10,00 22 17,0 6,0 15,0 5,50 11,0024 18,0 6,0 16,0 6,00 12,00 27 21,0 8,0 6,70 13,5030 23,0 8,0 7,50 15,00 33 26,0 10,0 8,20 16,5036 28,0 10,0 9,00 18,00 39 30,0

29、12,0 9,70 19,5042 32,0 12,0 10,50 21,00 45 35,0 14,0 11,20 22,5048 38,0 14,0 12,00 24,00 52 42,0 16,0 13,00 26,00aFor threads M1,6, dimensions and tolerances should be agreed as suitable. bFor nominal dimensions 1 mm, tolerance field h13 applies. cFor threads M5 no flat part on the cone is required;

30、 the point may be slightly rounded. dFor nominal dimensions 1 mm, tolerance field applies. IT130BS EN ISO 4753:2011ISO 4753:2011(E) ISO 2011 All rights reserved 53.3 Ends which are added to the specified nominal length of the fastener a) Pilot point, flat (PF) b) Pilot point with truncated cone (PC)

31、 aEnd may be dimpled. bIncomplete thread u 2 P. cThe angle applies only to the portion of the point below the root diameter of the thread. Figure 2 Table 2 Dimensions for flat pilot points Coarse thread Dimensions in millimetres Thread size M4 M5 M6 M8 M10 M12 M14 M16 M20 M24 dxamax. 2,9 3,8 4,5 6,1

32、 7,8 9,4 11,1 13,1 16,3 19,6 min. 2,7 3,6 4,3 5,9 7,6 9,1 10,8 12,8 15,9 19,2 z3IT1702,0 2,5 3,0 4,0 5,0 6,0 7,0 8,0 10,0 12,0 aIf, in special cases, a smaller diameter is required this shall be agreed separately. Table 3 Dimensions for pilot points with truncated cone Coarse thread Dimensions in mi

33、llimetres Thread size M4 M5 M6 M8 M10 M12 M14 M16 M20 M24 dxamax. 2,9 3,8 4,5 6,1 7,8 9,4 11,1 13,1 16,3 19,6 min. 2,7 3,6 4,3 5,9 7,6 9,1 10,8 12,8 15,9 19,2 z4IT1702,0 2,5 3,0 4,0 5,0 6,0 7,0 8,0 10,0 12,0 z5max. 1,00 1,50 2,00 2,50 3,00 3,50 4,00 4,50 5,00 6,00 min. 0,50 0,75 1,00 1,50 1,50 2,00

34、2,00 2,50 3,00 4,00 aIf, in special cases, a smaller diameter is required this shall be agreed separately. BS EN ISO 4753:2011ISO 4753:2011(E) 6 ISO 2011 All rights reservedTable 4 Dimensions for pilot points with truncated cone Fine pitch thread Dimensions in millimetres Thread size M8 1 M10 1 M12

35、1,5 M14 1,5 M16 1,5 dxmax. 6,30 8,00 9,60 11,40 13,50 min. 6,08 7,78 9,38 11,13 13,23z4IT1704 5 6 7 8 z5max. 2,5 3,0 3,5 4,0 4,5 min. 1,5 1,5 2,0 2,0 2,5 BS EN ISO 4753:2011This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparin

36、g British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick H

37、igh Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We

38、would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an indiv

39、idual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the web

40、site addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have

41、been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information ser

42、vices are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and ot

43、her benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publi

44、cations. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, p

45、hotocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: