BS EN 60264-3-4-1999 Packaging of winding wires - Taper barrelled delivery spools - Basic dimensions of containers for taper barrelled delivery spools - Taper barelled delivery spoa.pdf

《BS EN 60264-3-4-1999 Packaging of winding wires - Taper barrelled delivery spools - Basic dimensions of containers for taper barrelled delivery spools - Taper barelled delivery spoa.pdf》由会员分享，可在线阅读，更多相关《BS EN 60264-3-4-1999 Packaging of winding wires - Taper barrelled delivery spools - Basic dimensions of containers for taper barrelled delivery spools - Taper barelled delivery spoa.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 60264-3-4: 1999 IEC 60264-3-4: 1999 Packaging of winding wires Part3-4: Taper barrelled delivery spools Basic dimensions of containers for taper barrelled delivery spools The European Standard EN60264-3-4:1999 has the status of a British Standard ICS 55.060BSEN 60264-3-4:1999

2、This BritishStandard, having been prepared under the directionof the Electrotechnical Sector Committee, was publishedunder the authorityofthe Standards Committee andcomes into effect on 15 October1999 BSI03-2000 ISBN 0 580 35332 X National foreword This BritishStandard is the English language versio

3、n of EN60264-3-4:1999. It is identical with IEC60264-3-4:1999. It supersedes BS EN60264-3-4:1996 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee GEL/55, Winding wires, which has the responsibility to: aid enquirers to understand the text; present to t

4、he responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep theUKinterests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained

5、 on request to its secretary. From1 January1997, all IEC publications have the number60000 added to the old number. For instance, IEC27-1 has been renumbered as IEC60027-1. For a period of time during the change over from one numbering system to theother, publications may contain identifiers from bo

6、th systems. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publications. The BritishStandards which implement international or European publicati

7、ons referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisio

8、ns of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theEN title page, pag

9、es2 to4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSEN 60264-3-4:1999 BSI 03-

10、2000 i Contents Page National foreword Inside front cover Foreword 2 Text of EN 60264-3-4 3ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN60264-3-4 August1999 ICS 29.060.10; 55.060 Supersedes EN60264-3-4:1994 English version Packaging of winding wires Part3-4: Taper barrelled delivery s

11、pools Basic dimensions of containers for taper barrelled delivery spools (IEC60264-3-4:1999) Conditionnement des fils de bobinage Partie3-4: Bobines de livraison ft de forme conique Dimensions de base des conteneurs pour les bobines de livraison ft de forme conique (CEI60264-3-4:1999) Verpackung von

12、 Wickeldrhten Teil3-4: Lieferspulen mit konischem Kern Grundabmessungen der Behlter fr Lieferspulen mit konischem Kern (IEC60264-3-4:1999) This European Standard was approved by CENELEC on1999-08-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the co

13、nditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in

14、 three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotec

15、hnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normali

16、sation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1999 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref.No.EN60264-3-4:1999EEN 60264-3-4:1999 BSI 03-2000 2 Forew

17、ord The text of document55/662/FDIS, future edition2 of IEC60264-3-4, prepared by IEC TC55, Winding wires, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN60264-3-4 on1999-08-01. This European Standard supersedes EN60264-3-4:1994. The following dates were fixed: Annex

18、es designated “normative” are part of the body of the standard. In this standard, Annex ZA is normative. Annex ZA has been added by CENELEC. Endorsement notice The text of the International Standard IEC60264-3-4:1999 was approved by CENELEC as a European Standard without any modification. Contents P

19、age Foreword 2 Introduction 3 1 Scope 3 2 Normative references 3 3 Dimensions 3 4 Material 4 Annex ZA (normative) Normative references tointernational publications withtheir corresponding European publications Inside back cover Figure 1 Container for taper barrelleddeliveryspool 4 Table 1 Dimensions

20、 3 latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop)2000-05-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow)2002-08-01EN 60264-3-4:1999 BSI 03-2000 3 Introducti

21、on This part of IEC60264 is one of a series which deals with insulated wires used for windings in electrical equipment. The series comprises three groups describing: methods of test (IEC60851); specifications (IEC60317); packaging (IEC60264). 1 Scope This part of IEC60264 specifies the basic dimensi

22、ons of containers for taper barrelled delivery spools standardized in IEC60264-3-1. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of IEC60264. For dated references, subsequent amendments to, or re

23、visions of, any of these publications do not apply. However, parties to agreements based on this part of IEC60264 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative

24、 document referred to applies. Members of IEC and ISO maintain registers of currently valid International Standards. IEC60264-3-1:1989, Packaging of winding wires Part3: Taper barrelled delivery spools Section 1:Basic dimensions. 3 Dimensions The dimensions and tolerances of containers for taper bar

25、relled delivery spools are given in Table 1 in accordance with Figure 1. NOTEFigure 1 is given to identify the dimensions specified and is not intended to show any particular construction. Table 1 Dimensions Container for spool type Container dimensions mm d 1 d 2 d 3 h 1 h 2 Max. Nominal Tolerance

26、Nominal Tolerance Max. Min. 200/315 265 236 224 400 40 250/400 315 280 280 500 50 315/500 400 355 355 630 63 400/630 500 450 450 800 80 500/800 580 545 510 1000 100 0 2 0 125 , 0 25 , 0 15 0 35 , 0 20 0 50 , 0 25 0 63 , 0 25EN 60264-3-4:1999 4 BSI 03-2000 4 Material Requirements shall be stated in t

27、he purchasers order. Figure 1 Container for taper barrelled delivery spoolEN 60264-3-4:1999 BSI 03-2000 Annex ZA (normative) Normative references to international publications with their corresponding European publications This European Standard incorporates by dated or undated reference, provisions

28、 from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by ame

29、ndment or revision. For undated references the latest edition of the publication referred to applies (including amendments). NOTEWhen an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC60264-3-1

30、 1989 Packaging of winding wires Part 3: Taper barrelled delivery spools Section 1: Basic dimensions EN60264-3-1 1994BS EN 60264-3-4: 1999 IEC 60264-3-4: 1999 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing Britis

31、hStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the c

32、onstant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover.

33、Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer

34、 Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on na

35、tional, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscrib

36、ing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications.

37、BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopyi

38、ng, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.