BS EN 15821-2010 Multi-firing sauna stoves fired by natural wood logs Requirements and test methods《用天然圆木点燃多次燃烧蒸汽烤炉 要求和试验方法》.pdf

《BS EN 15821-2010 Multi-firing sauna stoves fired by natural wood logs Requirements and test methods《用天然圆木点燃多次燃烧蒸汽烤炉 要求和试验方法》.pdf》由会员分享，可在线阅读，更多相关《BS EN 15821-2010 Multi-firing sauna stoves fired by natural wood logs Requirements and test methods《用天然圆木点燃多次燃烧蒸汽烤炉 要求和试验方法》.pdf（60页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 15821:2010Multi-firing sauna stovesfired by natural wood logs Requirements and testmethodsBS EN 15821:2010 BRITISH STANDARDNational forewordThis British Standard is the UK

2、implementation of EN 15821:2010.The UK participation in its preparation was entrusted to TechnicalCommittee RHE/28, Domestic solid mineral fuel appliances.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all

3、 the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2010ISBN 978 0 580 57335 4ICS 97.100.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Stra

4、tegy Committee on 31 October 2010.Amendments issued since publicationDate Text affectedBS EN 15821:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15821 September 2010 ICS 97.100.10 English Version Multi-firing sauna stoves fired by natural wood logs - Requirements and test methods Poles de

5、 sauna allumage multiple bches de bois naturelles - Exigences et mthodes dessai Mehrfach befeuerbare Saunafen zur Verfeuerung fester Brennstoffe - Anforderungen und Prfverfahren This European Standard was approved by CEN on 7 August 2010. CEN members are bound to comply with the CEN/CENELEC Internal

6、 Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.

7、 This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members

8、are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Swe

9、den, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.

10、 Ref. No. EN 15821:2010: EBS EN 15821:2010EN 15821:2010 (E) 2 Contents Page Foreword . 41 Scope 52 Normative references . 53 Terms and definitions . 54 Requirements for materials, design and construction . 94.1 Production documentation 94.2 Construction 104.2.1 General construction 104.2.2 Cleaning

11、of heating surfaces . 104.2.3 Flue spigot or socket 104.2.4 Ashpan and ash removal 104.2.5 Bottomgrate . 114.2.7 Control of flue gas 114.2.8 Firedoors and charging doors . 114.2.9 Flue bypass device . 124.2.10 Front firebars and/or deepening plate 125 Safety requirements 125.1 Temperature rise of th

12、e operating components 125.2 Temperature of adjacent combustible materials . 126 Performance requirements 126.1 Flue gas temperature 126.2 Carbon monoxide emission . 136.3 Efficiency . 136.4 Flue draught 136.5 Refuelling loads 136.6 Space heating output 137 Instructions 137.1 General . 137.2 Install

13、ation instructions 137.3 User operating instructions . 148 Evaluation of conformity 158.1 General . 158.2 Initial type testing 168.2.1 General . 168.2.2 Initial type testing for appliance changes 178.3 Factory production control (FPC) . 198.3.1 General . 198.3.2 Raw materials and components 198.3.3

14、Control of inspection, measuring and test equipment . 198.3.4 Process control . 198.3.5 Product inspection, testing and evaluation . 198.3.6 Non conforming products 218.3.7 Corrective and preventive action 218.3.8 Handling, storage, packaging, preservation and delivery 219 Marking. 21Annex A (normat

15、ive) Test methods 22A.1 Test environment 22A.1.1 Sauna test room temperature 22BS EN 15821:2010EN 15821:2010 (E) 3 A.1.2 Ambient air temperature coming into the sauna test room . 22A.1.3 External sources . 22A.2 Test assembly . 22A.2.1 General . 22A.2.2 Sauna test room 23A.2.3 Measurement section .

16、23A.2.4 Connection of appliance to measurement section . 24A.3 Measurement equipment . 25A.4 Test procedures 25A.4.1 Appliance installation . 25A.4.2 Fuel load 25A.4.3 Fuelling and de-ashing the fire 26A.4.4 Flue gas losses . 26A.4.5 Combustible heat losses in the residue . 26A.4.6 Performance test

17、at nominal heat output . 26A.4.7 Temperature safety test . 28A.5 Test results 29A.6 Calculation methods. 29A.6.1 Notations and units used . 29A.6.2 Formulae 31A.7 Test report . 33Annex B (normative) Test fuels and recommended fuels 43B.1 General . 43B.2 Test fuel . 43B.2.1 Selection of test fuel . 4

18、3B.2.2 Storage, preparation and analysis 43Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive . 46ZA.1 Scope and relevant characteristics 46ZA.2 Procedure for the attestation of conformity of multi-firing sauna stoves fired by

19、 natural wood logs 48ZA.3 CE marking and labelling . 50BS EN 15821:2010 EN 15821:2010 (E) 4 Foreword This document (EN 15821:2010) has been prepared by Technical Committee CEN/TC 295 “Residential solid fuel burning appliances”, the secretariat of which is held by BSI. This European Standard shall be

20、 given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2011, and conflicting national standards shall be withdrawn at the latest by June 2012. Attention is drawn to the possibility that some of the elements of this document may

21、be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC

22、Directive(s). For relationship with EC Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgiu

23、m, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 15821

24、:2010EN 15821:2010 (E) 5 1 Scope This European Standard covers multi-firing sauna stoves in which the heating stones are separated from and indirectly heated by the fire and the flue gases and which may be re-fuelled with several fuel loads. This European Standard specifies requirements relating to

25、the design, manufacture, construction, safety and performance (efficiency and emission) of multi-firing sauna stoves fired by wood logs and provides instructions for them. Furthermore, it also gives provisions for evaluation of conformity (i.e. initial type testing (ITT) and factory production contr

26、ol (FPC) and marking of these products. This standard is applicable to hand-fuelled intermittent burning multi-firing sauna stoves, which provide heat into the space where they are installed. These multi-firing sauna stoves may be supplied either as an assembled appliance or as a manufacturers pre-d

27、esigned unit consisting of pre-fabricated components designed to be built on site in accordance with the manufacturers specified assembly instructions. One-off installations are not included. These multi-firing sauna stoves may burn only natural wood logs in accordance with the appliance operating i

28、nstructions. Single-firing heat storage sauna stoves, in which the stones are directly heated by the fire and the flue gases, which pass through them, are not covered by this European Standard. This standard is also not applicable to mechanically fed sauna stoves, sauna stoves having fan assisted co

29、mbustion air, sauna stoves fitted with a boiler, sauna stoves with incorporated flue or sauna stoves having any electrical connection. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applie

30、s. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 14774-1, Solid biofuels Determination of moisture content Oven dry method Part 1: Total moisture Reference method EN 14775, Solid biofuels Determination of ash content EN 14918, Solid biof

31、uels Determination of calorific value EN 15104, Solid biofuels Determination of total content of carbon, hydrogen and nitrogen Instrumental methods EN 15148, Solid biofuels Determination of the content of volatile matter EN 15289, Solid Biofuels Determination of total content of sulphur and chlorine

32、 EN 60335-2-53, Household and similar electrical appliances Safety Part 2-53: Particular requirements for sauna heating appliances (IEC 60335-2-53:2002) EN ISO 9001:2008, Quality management systems Requirements (ISO 9001:2008) ISO 2859 (all parts), Sampling procedures for inspection by attributes 3

33、Terms and definitions For the purposes of this document, the following terms and definitions apply. BS EN 15821:2010EN 15821:2010 (E) 6 3.1 air grilles components in the inlet and outlet openings to distribute and direct convection air flow 3.2 air inlet control manual or automatic device which cont

34、rols the quantity of air supplied for combustion 3.3 appliance family group of appliances of similar construction and/or performance characteristics where it is permissible to test only selected appliances in accordance with the requirements of this standard 3.4 ash content of the fuel solid matter

35、remaining after the complete combustion of solid fuel 3.5 ashpan removable receptacle shaped to receive the residue falling from the firebed 3.6 ashpit enclosed chamber designed to receive the residue or the ashpan 3.7 ashpit loss part of the residue which is combustible 3.8 basic firebed quantity o

36、f glowing embers which ensures ignition of the test fuel to be charged NOTE The basic firebed may be specified in the operating instructions. 3.9 batch charge proportion of the test load as declared in the operating manual that can be added at specified intervals during the test period of the burnin

37、g rate performance test 3.10 bottomgrate part of the appliance at the base of the firebox which supports the firebed through which the residue falls into the ashpan or ashpit and through which combustion air and/or combustion gases may be drawn 3.11 bottomgrate bars firebars bars supporting the fuel

38、bed, separate or integral with a surrounding frame 3.12 charging door door which covers the refuelling opening 3.13 combustion air air supplied to the firebox which is entirely or partially used to burn the fuel 3.14 combustion gases compounds in gaseous form produced inside an appliance when fuel i

39、s burned BS EN 15821:2010EN 15821:2010 (E) 7 3.15 de-ashing process of clearing a fuelbed and discharging the residue into the collecting receptacle 3.16 de-ashing mechanism device to agitate or disturb the ash to facilitate its removal from the firebed NOTE It may also be used to change the bottomg

40、rate operating position on some multi-firing sauna stoves. 3.17 draught regulator inlet device for admission of air downstream of the firebed, enabling the flue draught to be controlled 3.18 efficiency ratio of total heat output to the total heat input during the burning period expressed as a percen

41、tage 3.19 firebox combustion chamber part of the multi-firing sauna stove in which the fuel is burned 3.20 firebox opening aperture in the firebox through which a multi-firing sauna stove may be fuelled 3.21 firedoor door through which the fire may be viewed and which may be opened to allow refuelli

42、ng of the firebed 3.22 flue by-pass device device which in the open position allows flue gases to pass directly to the flue spigot/socket NOTE This can be used as a preheating aid to overcome chimney condensation. 3.23 flue damper mechanism to change the flow of the combustion gases 3.24 flue draugh

43、t differential between the static pressure in the place of installation and the static pressure at the flue gas measurement point 3.25 flue gases gaseous compounds leaving the multi-firing sauna stove flue spigot or socket and entering the flue gas connector 3.26 flue gas connector duct through whic

44、h flue gases are conveyed from the flue spigot of the multi-firing sauna stove into the chimney flue 3.27 flue gas mass flow mass of flue gas drawn off from the multi-firing sauna stove per unit of time BS EN 15821:2010EN 15821:2010 (E) 8 3.28 flue gas temperature temperature of the flue gas at the

45、specified point in the measurement section 3.29 flue spigot flue socket integral part of the multi-firing sauna stove for connecting the flue gas connector thus permitting the deliberate escape of products of combustion into the chimney flue 3.30 flueway part of a multi-firing sauna stove designed t

46、o convey combustion gases from the firebox to the flue spigot/socket 3.31 front firebars grating or plate fitted at the front of the firebox opening to prevent spillage of fuel and ash or to change the firebox capacity, or both 3.32 total heat input quantity of energy which the fuel provides to the

47、multi-firing sauna stove 3.33 integral fuel storage container enclosed area forming part of the multi-firing sauna stove, but not connected directly to the fuel charging area, in which fuel is stored prior to it being physically transferred by the user to the fuel charging position 3.34 operating to

48、ol device supplied with the multi-firing sauna stove for handling movable and/or hot components 3.35 primary air combustion air which passes through the fuel bed 3.36 recommended fuel fuel of commercial quality, listed in the multi-firing sauna stove operating instructions, and shown to achieve the claimed performance when tested in accordance with this European Standard 3.37 residue ashes, including combustibles, which collect in the ashpit 3.38 sauna stove stove that has a fully enclosed firebox with a firedoor which is normally closed