BS EN 15036-1-2006 Heating boilers - Test regulations for airborne noise emissions from heat generators - Part 1 Airborne noise emissions from heat generators《加热锅炉 热产生器发出空气噪声的试验规则 .pdf

《BS EN 15036-1-2006 Heating boilers - Test regulations for airborne noise emissions from heat generators - Part 1 Airborne noise emissions from heat generators《加热锅炉 热产生器发出空气噪声的试验规则 .pdf》由会员分享，可在线阅读，更多相关《BS EN 15036-1-2006 Heating boilers - Test regulations for airborne noise emissions from heat generators - Part 1 Airborne noise emissions from heat generators《加热锅炉 热产生器发出空气噪声的试验规则 .pdf（42页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58emissions from heat generators Part 1: Airborne noise emissions from heat generatorsThe European St

2、andard EN 15036-1:2006 has the status of a British StandardICS 17.140.20; 91.140.10Heating boilers Test regulations for airborne noise BRITISH STANDARDBS EN 15036-1:2006BS EN 15036-1:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 Octo

3、ber 2006 BSI 2006ISBN 0 580 49375 XAmendments issued since publicationAmd. No. Date Commentscontract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.National forewordThis British Standard was published by BSI. It is

4、the UK implementation of EN 15036-1:2006.The UK participation in its preparation was entrusted to Technical Committee RHE/10, Heating boilers.A list of organizations represented on RHE/10 can be obtained on request to its secretary.This publication does not purport to include all the necessary provi

5、sions of a EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15036-1September 2006ICS 17.140.20; 91.140.10English VersionHeating boilers - Test regulations for airborne noise emissionsfrom heat generators - Part 1: Airborne noise emissions fromheat generatorsChaudires de chauffage - Rgles dessais de

6、s missionsde bruit arien des gnrateurs de chaleur - Partie 1 :missions du bruit arien des gnrateurs de chaleurHeizkessel - Prfverfahren fr Luftschallemissionen vonWrmeerzeugern - Teil 1: Luftschallemissionen vonWrmeerzeugernThis European Standard was approved by CEN on 14 August 2006.CEN members are

7、 bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the

8、 Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status

9、as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slove

10、nia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN natio

11、nal Members.Ref. No. EN 15036-1:2006: EEN 15036-1:2006 (E) 2 Contents Page Foreword4 Introduction .5 1 Scope 6 2 Normative references 6 3 Terms and definitions .7 4 Determining sound power levels .7 4.1 General data .7 4.2 Test method8 4.2.1 Measurement approach 8 4.2.2 Uncertainty of test .8 4.2.3

12、Selection of test methods .9 4.2.4 Operation 11 5 Set up and operation of the appliances 11 5.1 General11 5.2 Equipment and preliminary treatment.11 5.3 Climatic conditions11 5.4 Operation of the appliance .11 6 Test report 12 6.1 General12 6.2 Information and readings in the test report 12 6.2.1 Ge

13、neral information in the report.12 6.2.2 Information on measured data .13 Annex A (normative) Free field method.14 A.1 General14 A.2 Principle14 A.3 Test equipment 17 A.4 Location and number of measurement points .17 A.5 Determination of sound power level according to EN ISO 3744 and EN ISO 3746.20

14、A.5.1 Test procedure.20 A.5.2 Calculation of sound pressure level averaged over the measurement surface .21 A.5.3 Calculation of A-weighted sound pressure levels from frequency band data21 A.5.4 Correction for background noise.23 A.5.5 Correction for the test environment 23 A.5.6 Calculation of the

15、surface sound pressure level25 A.5.7 Calculation of the sound power level 25 Annex B (normative) Reverberant room method .26 B.1 General26 B.2 Principle26 B.3 Test equipment 26 B.4 Environment.26 B.5 Sound pressure measurements.26 B.6 Calculation of sound pressure level average .27 EN 15036-1:2006 (

16、E) 3 B.7 Background noise correction 27 B.8 Calculation of the average sound power spectrum.28 B.8.1 Comparative method.28 B.8.2 Direct method 28 B.9 Determination of A-weighted sound power level.29 Annex C (normative) Sound intensity method .30 C.1 General .30 C.2 Principle .30 C.3 Test equipment30

17、 C.4 Measuring points and procedure.31 C.4.1 General .31 C.4.2 Test according to EN ISO 9614-1 (discrete points)31 C.4.3 Test according to EN ISO 9614-2 (scanning)32 C.5 Calculation of sound power levels 33 Annex D (informative) Examples for free field method category 3 34 Annex E (informative) Micr

18、ophone positions.38 EN 15036-1:2006 (E) 4 Foreword This document (EN 15036-1:2006) has been prepared by Technical Committee CEN/TC 57 “Central heating boilers”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of

19、an identical text or by endorsement, at the latest by March 2007, and conflicting national standards shall be withdrawn at the latest by March 2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European

20、 Standard : Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 1503

21、6-1:2006 (E) 5 Introduction Generally speaking, determining the airborne noise emissions is only part of a comprehensive testing programme which takes into account many different viewpoints relating to the characteristics and behaviour in using a heat generator. It is therefore important that the re

22、quirements for noise tests, such as the measuring equipment and the environment in which it is used should always be considered within the prescribed context. It is also important whatever the ultimate purpose may be, to lay down procedures within a defined degree of accuracy, so that the measuring

23、results obtained from various different laboratories can be compared with one another. These conditions have been taken into account as far as possible in preparing these test methods. All test procedures defined in EN ISO 3741, EN ISO 3743, EN ISO 3744, EN ISO 3746 and EN ISO 9614 are permissible m

24、ethods. It should be emphasised that these test methods only apply to airborne noise. In many cases, however, structure-borne noise, such as can be transmitted into a neighbouring room, can also be of significance. It is envisaged that airborne noise emissions through the flue gas path will be dealt

25、 with in a separate part of this standard. All the basic and noise measurement standards of accuracy categories 1 to 3 are permissible under this testing standard. Sound values declared by the manufacturer can be measured according to these three categories, but in any case, the used category has to

26、 be stated. This European Standard sets out various methods for testing to approximate the airborne noise emitted by heat generators into the room of installation. EN 15036-1:2006 (E) 6 1 Scope This European Standard specifies test methods for airborne noise emissions from heat generators in a test

27、laboratory or at the place of installation. The test methods described in this European Standard, however, may be used for measuring the airborne noise emissions of the appliances and functions listed below. This European Standard applies to following appliances regardless of their heat output and t

28、he fuel used: wall-mounted and floor-standing heating appliances; forced-draught burners; boilers/forced-draught burner units; boilers with freely allocated forced-draught burners; pellet burners. According to this European Standard the manufacturer is allowed to choose an appropriate category of te

29、sting for the measured appliance. This European Standard does not apply to: appliances used exclusively for heating drinking-water; function of heating drinking-water in so-called combined water-heaters; heat generators which work with air as the heat transfer medium; electrical heating appliances;

30、structure-borne noise; sound transmission along the flue gas path. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docu

31、ment (including any amendments) applies. EN 267, Forced draught oil burners Definitions, requirements, testing, marking EN 437, Test gases Test pressures Appliance categories EN 676, Automatic forced draught burners for gaseous fuels EN ISO 3741, Acoustics Determination of sound power levels of nois

32、e sources using sound pressure Precision methods for reverberation rooms (ISO 3741:1999). EN 15036-1:2006 (E) 7 EN ISO 3743-1:1995, Acoustics Determination of sound power levels of noise sources Engineering methods for small, movable sources in reverberant fields Part 1: Comparison method for hard-w

33、alled test rooms (ISO 3743-1:1994) EN ISO 3743-2:1996, Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering methods for small, movable sources in reverberant fields - Part 2: Methods for special reverberation test rooms (ISO 3743-2:1994) EN ISO 3744:199

34、5, Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering method in an essentially free field over a reflecting plane (ISO 3744:1994) EN ISO 3745, Acoustics - Determination of sound power levels of noise sources using sound pressure - Precision methods fo

35、r anechoic and semi-anechoic rooms (ISO 3745:2003) EN ISO 3746:1995, Acoustics - Determination of sound power levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:1995) EN ISO 9614-1:1995, Acoustics - Determination of

36、sound power levels of noise sources using sound intensity - Part 1: Measurements at discrete points (ISO 9614-1:1993) EN ISO 9614-2:1996, Acoustics Determination of the sound power levels of noise sources using sound intensity Part 2: Measurements by scanning (ISO 9614-2:1996) EN ISO 9614-3:2002, Ac

37、oustics Determination of the sound power levels of noise sources using sound intensity Part 3: Precision method for measurement by scanning (ISO 9614-3:2002) 3 Terms and definitions For the purposes of this standard, the terms and definitions given in EN ISO 3743-1:1995, EN ISO 3743-2:1996, EN ISO 3

38、744:1995, EN ISO 3746:1995, EN ISO 9614-1:1995, EN ISO 9614-2:1996 and EN ISO 9614-3:2002 and the following apply. 3.1 heat generator device suitable for the combustion of liquid, gaseous and solid fuels 4 Determining sound power levels 4.1 General data The sound power W, of a noise source is the to

39、tal sound energy radiated by that source per second, expressed in Watts (W). The sound power W, is customarily related to a reference sound power W0and expressed as a sound power level LWin decibels (dB) according to equation (1): 010WWL logW= (1) where W0is the reference sound power level of 1 pW (

40、= 1012W). EN 15036-1:2006 (E) 8 The main criteria for determining the choice of sound power level for the purpose of labelling the noise emission are: a) sound power level shall provide an adequate description of the noise emission and is independent of environmental factors; b) it shall be possible

41、 to determine the sound power level to a defined degree of accuracy from relatively simple acoustic tests which can be carried out under a large number of defined acoustic conditions. These test methods describe the objective procedure for determining the sound power level of airborne noise, LW. The

42、 following sound power levels can be determined: A-weighted sound power level LWA; sound power level in octave bands, LWOct.Tests shall be carried out on a frequency band covering at least an octave band from 125 Hz to 4000 Hz; sound power level in third bands, LWThird. Tests shall be carried out on

43、 a frequency band covering at least third-octave bands from 100 Hz to 5000 Hz. For practical use, LWAtest-stand measurements are sufficient for calculating the A-weighted sound power level. 4.2 Test method 4.2.1 Measurement approach To determine sound power level, there are three basic procedures. T

44、hese are: Conversion of sound pressure level measured into a reverberant field to sound power level. This approach is described in EN ISO 3741 and EN ISO 3743-1 and EN ISO 3743-2. Conversion of sound pressure level measured into a free-field (or assimilated to a free-field) according to EN ISO 3744,

45、 EN ISO 3745 and EN ISO 3746. Conversion of intensity field emitted around the appliance to sound power level. This approach is described in EN ISO 9614-1, EN ISO 9614-2 and EN ISO 9614-3. 4.2.2 Uncertainty of test Within each measurement approach in 4.2.1, different methods are described by specifi

46、c standards in order to reach different levels of accuracy on the final results. These accuracy levels are the following (from the best to the worst accuracy): Category 1 describes the precision class; Category 2 describes the engineering class; Category 3 describes the survey class. NOTE 1 For inst

47、ance, using a free-field approach, the three relevant standards are EN ISO 3745 (Category 1), EN ISO 3744 (Category 2) and EN ISO 3746 (Category 3). If the experimental approach is similar (measure of average sound pressure level on a fictitious area including the appliance), test requirements are d

48、ifferent depending on the targeted level of accuracy (number of points, difference between background and appliance noise, test environment correction, etc.). EN 15036-1:2006 (E) 9 NOTE 2 Depending on the accuracy category, the available information is different. Survey methods do not provide spectr

49、al data. According to accuracy categories, standard deviations on A-weighted are provided in Table 1. Table 1 - Standard deviations on A-weighted overall sound power level according to accuracy categories of standards Precision class Engineering class Survey class Standard deviation RdB 1 1,5 4 These standard deviations relate to a relatively flat spectrum. In case of tonal noise, standard deviation of the survey method is increased by 1 dB. In the hypothesis of a