BS EN 15008-2017 Aerosol containers Aluminium containers - Dimensions of one-piece cans with 25 4 mm aperture《雾化剂罐 铝罐 孔径25 4 mm的整体罐尺寸规格》.pdf

《BS EN 15008-2017 Aerosol containers Aluminium containers - Dimensions of one-piece cans with 25 4 mm aperture《雾化剂罐 铝罐 孔径25 4 mm的整体罐尺寸规格》.pdf》由会员分享，可在线阅读，更多相关《BS EN 15008-2017 Aerosol containers Aluminium containers - Dimensions of one-piece cans with 25 4 mm aperture《雾化剂罐 铝罐 孔径25 4 mm的整体罐尺寸规格》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、Aerosol containers Aluminium containers Dimensions of one-piece cans with 25,4 mm apertureBS EN 15008:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15008 March 2017 ICS 55.130 Supersedes EN 15008:2006English

2、Version Aerosol containers - Aluminium containers - Dimensions of one-piece cans with 25,4 mm aperture Rcipients pour arosols - Rcipients en aluminium - Dimensions des botiers monoblocs (une pice) avec ouverture de 25,4 mm Aerosolpackungen - Aluminiumbehlter - Mae von einteiligen Behltern mit einer

3、ffnung von 25,4 mm This European Standard was approved by CEN on 7 February 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and

4、bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the re

5、sponsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav

6、Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EURO

7、PEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15008:2017 ENational forewordThis British Standard is the UK

8、implementation of EN 15008:2017. It supersedes BS EN 15008:2006 , which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PKW/0/-/8, Packaging - Metals.A list of organizations represented on this committee can be obtained on request to its secretary.This publi

9、cation does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 93220 5ICS 55.130Compliance with a British Standard cannot confer immunity fr

10、om legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 15008:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15008 Marc

11、h 2017 ICS 55.130 Supersedes EN 15008:2006English Version Aerosol containers - Aluminium containers - Dimensions of one-piece cans with 25,4 mm aperture Rcipients pour arosols - Rcipients en aluminium - Dimensions des botiers monoblocs (une pice) avec ouverture de 25,4 mm Aerosolpackungen - Aluminiu

12、mbehlter - Mae von einteiligen Behltern mit einer ffnung von 25,4 mm This European Standard was approved by CEN on 7 February 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national stan

13、dard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in a

14、ny other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Rep

15、ublic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.

16、 EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15008:2017

17、EBS EN 15008:2017EN 15008:2017 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Requirements . 4 4.1 Classification of containers 4 4.2 Filling volumes . 4 Bibliography . 11 BS EN 15008:2017EN 15008:2017 (E) 3 European foreword This document

18、(EN 15008:2017) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2017, and conf

19、licting national standards shall be withdrawn at the latest by September 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersed

20、es EN 15008:2006. This draft European Standard is one of a package of 10 related standards with the following titles: EN 14847, Aerosol containers Tinplate containers Dimensions of the 25,4 mm aperture; EN 14848, Aerosol containers Metal containers with 25,4 mm aperture Dimensions of valve cups; EN

21、14849, Aerosol containers Glass containers Dimensions of aerosol valve ferrules; EN 14850, Aerosol containers Metal containers with 25,4 mm aperture Measurement of contact height; EN 14854, Aerosol containers Glass containers Dimensions of the neck finish; EN 15006, Metal aerosol containers Aluminiu

22、m containers Dimensions of the 25,4 mm aperture; EN 15007, Aerosol containers Tinplate containers Dimensions of two and three-piece cans; EN 15008, Aerosol containers Aluminium containers Dimensions of one-piece cans with 25,4 mm aperture; EN 15009, Aerosol containers Compartmented aerosol container

23、s; EN 15010, Aerosol containers Aluminium containers Tolerances of the fundamental dimensions in connection with the clinch. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belg

24、ium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden

25、, Switzerland, Turkey and the United Kingdom. BS EN 15008:2017EN 15008:2017 (E) 4 1 Scope This European Standard specifies the dimensions and volumes for one-piece aluminium aerosol containers with a 25,4 mm aperture. This European Standard applies to one-piece containers of monobloc construction wi

26、th an ogival, spherical or flat shoulder. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of th

27、e referenced document (including any amendments) applies. EN 15010, Aerosol containers - Aluminium containers - Tolerances of the fundamental dimensions in connection with the clinch 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 monobloc co

28、nstruction construction without seaming, welding or soldering 3.2 brimful capacity capacity, in millilitres, of an aerosol container without an aerosol valve 4 Requirements 4.1 Classification of containers One-piece aluminium aerosol containers shall be classified according to five characteristic di

29、mensions: a) brimful capacity (C2); b) nominal outside diameter (De) which, when measured in accordance with EN 15010, shall have a tolerance of 0,3 mm; c) cover seat height (H2), which shall be as shown in Figure 1 and which shall have a tolerance of 0,5 mm measured at (De 2) mm; d) nominal overall

30、 height (H3), which shall be as shown in Figure 1 and which shall have a tolerance of 0,4 mm; e) shoulder, which shall be either ogival, spherical or flat as shown in Figure 1. 4.2 Filling volumes The filling volumes of aerosol containers with ogival shoulders shall be as shown in Table 1. The filli

31、ng volumes of aerosol containers with spherical shoulders shall be as shown in Table 2. The filling volumes of aerosol containers with flat shoulders shall be as shown in Table 3. BS EN 15008:2017EN 15008:2017 (E) 5 Dimensions in millimetres Key A ogival shoulder B spherical shoulder C flat shoulder

32、 Figure 1 Dimensions and shoulder profiles BS EN 15008:2017EN 15008:2017 (E) 6 Table 1 Containers with ogival shoulder Brimful capacityaNominal filling volume Nominal outside diameter Nominal overall height Cover seat height C2V nom. min. max. liquefied gasbcompressed gascDeH3H2ml ml ml ml ml mm mm

33、mm 47 45 49 25 35 59 7,7 75 72 78 50 35 88 7,7 89 85 93 50 35 105 7,7 38 90 11,0 110 106 114 75 35 125 7,7 38 110 11,0 40 100 12,0 140 134 146 100 75 35 156 7,7 38 138 11,0 40 125 12,0 42 115 12,5 45 105 15,0 175 169 181 125 100 38 168 11,0 40 156 12,0 42 142 12,5 45 125 15,0 210 204 216 150 125 40

34、183 12,0 42 165 12,5 45 150 15,0 47 137 16,5 50 125 18,5 270 262 278 200 150 45 190 15,0 47 176 16,5 50 156 18,5 53 142 20,5 BS EN 15008:2017EN 15008:2017 (E) 7 Brimful capacityaNominal filling volume Nominal outside diameter Nominal overall height Cover seat height C2V nom. min. max. liquefied gasb

35、compressed gascDeH3H2ml ml ml ml ml mm mm mm 335 325 345 250 200 47 214 16,5 50 190 18,5 53 173 20,5 55 162 22,0 59 142 24,5 405 393 417 300 250 47 254 16,5 50 225 18,5 53 205 20,5 55 191 22,0 57 180 23,5 59 169 24,5 64 150 28,5 66 143 29,0 520 507 533 400 300 53 260 20,5 55 242 22,0 57 226 23,5 59

36、214 24,5 64 185 28,5 66 178 29,0 650 637 663 500 400 57 277 23,5 59 265 24,5 64 230 28,5 66 218 29,0 800 784 816 600 500 66 263 29,0 74 210 34,5 1 000 980 1 020 750 600 66 322 29,0 74 263 34,5 aThe minimum and maximum values have been calculated in accordance with EN ISO 90-3 1. bProducts propelled

37、by liquefied gas. cProducts propelled by compressed gases alone and products propelled by nitrous oxide or carbon dioxide alone or by mixtures of the two alone when the product has a Bunsen coefficient of 1,2 or less. BS EN 15008:2017EN 15008:2017 (E) 8 Table 2 Containers with spherical shoulder Bri

38、mful capacityaNominal filling volume Nominal outside diameter Nominal overall height Cover seat height C2V nom. min. max. liquefied gasbcompressed gascDeH3H2ml ml ml ml ml mm mm mm 47 45 49 25 35 59 7,0 75 72 78 50 35 88 7,0 89 85 93 50 35 105 7,0 110 106 114 75 35 125 7,0 40 100 11,0 140 134 146 10

39、0 75 35 156 7,0 40 125 11,0 45 105 14,0 175 169 181 125 100 40 156 11,0 45 125 14,0 210 204 216 150 125 40 183 11,0 45 150 14,0 47 137 14,5 50 125 16,0 270 262 278 200 150 45 190 14,0 47 176 14,5 50 156 16,0 53 142 18,0 335 325 345 250 200 47 214 14,5 50 190 16,0 53 173 18,0 59 142 21,6 405 393 417

40、300 250 47 254 14,5 50 225 16,0 53 205 18,0 59 169 21,6 64 150 23,5 BS EN 15008:2017EN 15008:2017 (E) 9 Brimful capacityaNominal filling volume Nominal outside diameter Nominal overall height Cover seat height C2V nom. min. max. liquefied gasbcompressed gascDeH3H2ml ml ml ml ml mm mm mm 520 507 533

41、400 300 53 260 18,0 59 214 21,6 64 185 23,5 650 637 663 500 400 59 265 21,6 64 230 23,5 aThe minimum and maximum values have been calculated in accordance with EN ISO 90-3 1. bProducts propelled by liquefied gas. cProducts propelled by compressed gases alone and products propelled by nitrous oxide o

42、r carbon dioxide alone or by mixtures of the two alone when the product has a Bunsen coefficient of 1,2 or less. Table 3 Containers with flat shoulder Brimful capacityaNominal filling volume Nominal outside diameter Nominal overall height Cover seat height C2V nom. min. max. liquefied gasbcompressed

43、 gascDeH3H2ml ml ml ml ml mm mm mm 140 134 146 100 75 45 100 7 175 169 181 125 100 45 123 7 210 204 216 150 125 45 146 7 50 121 9,4 53 110 9,6 270 262 278 200 150 50 152 9,4 53 139 9,6 335 325 345 250 200 50 186 9,4 53 170 9,6 405 393 417 300 250 53 202 9,6 59 168 11,4 BS EN 15008:2017EN 15008:2017

44、(E) 10 Brimful capacityaNominal filling volume Nominal outside diameter Nominal overall height Cover seat height C2V nom. min. max. liquefied gasbcompressed gascDeH3H2ml ml ml ml ml mm mm mm 520 507 533 400 300 59 211 11,4 66 173 13,5 650 637 663 500 400 59 260 11,4 66 210 13,5 800 784 816 600 500 6

45、6 257 13,5 aThe minimum and maximum values have been calculated in accordance with EN ISO 90-3 1. bProducts propelled by liquefied gas. cProducts propelled by compressed gases alone and products propelled by nitrous oxide or carbon dioxide alone or by mixtures of the two alone when the product has a

46、 Bunsen coefficient of 1,2 or less. BS EN 15008:2017EN 15008:2017 (E) 11 Bibliography 1 EN ISO 90-3, Light gauge metal containers - Definitions and determination of dimensions and capacities - Part 3: Aerosol cans (ISO 90-3) BS EN 15008:2017This page deliberately left blankThis page deliberately lef

47、t blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Instituti

48、on (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open

49、 consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including Br