BS EN 15006-2006 Metal aerosol containers - Aluminium containers - Dimensions of nthe 25 4 mm aperture《金属雾化剂罐 铝罐 孔径25 4 mm尺寸规格》.pdf

《BS EN 15006-2006 Metal aerosol containers - Aluminium containers - Dimensions of nthe 25 4 mm aperture《金属雾化剂罐 铝罐 孔径25 4 mm尺寸规格》.pdf》由会员分享，可在线阅读，更多相关《BS EN 15006-2006 Metal aerosol containers - Aluminium containers - Dimensions of nthe 25 4 mm aperture《金属雾化剂罐 铝罐 孔径25 4 mm尺寸规格》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 15006:2006Metal aerosol containers Aluminium containers Dimensions of the 25,4 mm apertureThe European Standard EN 15006:2006 has the status of a British StandardICS 55.130g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38

2、g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Licensed Copy: Wang Bin, na, Wed Apr 11 02:27:09 GMT+00:00 2007, Uncontrolled Copy, (c) BSIBS EN 15006:2006This British Standard was published under the authority of the Standards Policy and Strategy Commit

3、tee on 31 January 2007 BSI 2007ISBN 978 0 580 50123 4National forewordThis British Standard was published by BSI. It is the UK implementation of EN 15006:2006. The UK participation in its preparation was entrusted to Technical Committee PKW/0, Packaging.A list of organizations represented on PKW/0 c

4、an be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAm

5、d. No. Date CommentsLicensed Copy: Wang Bin, na, Wed Apr 11 02:27:09 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15006October 2006ICS 55.130English VersionMetal aerosol containers - Aluminium containers - Dimensions ofthe 25,4 mm apertureRcipients mtal

6、liques pour arosols - Rcipients enaluminium - Dimensions des botiers avec ouverture de25,4 mmAerosolpackungen - Aluminiumbehlter - Mae der 25,4mm weiten ffnungThis European Standard was approved by CEN on 6 August 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which s

7、tipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard e

8、xists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bod

9、ies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMIT

10、TEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15006:2006: ELicensed Copy: Wang Bin, na,

11、Wed Apr 11 02:27:09 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 15006:2006 (E) 2 Contents Page Foreword3 Introduction .4 1 Scope 5 2 Normative references 5 3 Requirements for specifying and measuring .5 3.1 Dimensions of the 25,4 mm aperture.5 3.2 Contact height6 3.3 Outside diameter6 3.4 Inside di

12、ameter.6 3.5 Shoulder height6 Bibliography 7 Licensed Copy: Wang Bin, na, Wed Apr 11 02:27:09 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 15006:2006 (E) 3 Foreword This document (EN 15006:2006) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNO

13、R. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2007, and conflicting national standards shall be withdrawn at the latest by April 2007. This draft European Standard is one of a series of

14、 thirteen related standards with the following titles: EN 14847, Aerosol containers Tinplate containers Dimensions of the 25,4 mm aperture EN 14848, Aerosol containers Metal containers with 25,4 mm aperture Dimensions of valve cups EN 14849, Aerosol containers Glass containers Dimensions of aerosol

15、valve ferrules EN 14850, Aerosol containers Metal containers with 25,4 mm aperture Measurement of contact height EN 14851, Aerosol containers Aerosol foam flammability test EN 14852, Aerosol containers Determination of the ignition distance of the spray jet EN 14853, Aerosol containers Enclosed spac

16、e ignition test EN 14854, Aerosol containers Glass containers Dimensions of the neck finish EN 15006, Metal aerosol containers Aluminium containers Dimensions of the 25,4 mm aperture EN 15007, Metal aerosol containers Tinplate containers Dimensions of two and three-piece cans EN 15008, Aerosol conta

17、iners Aluminium containers Dimensions of one-piece cans with 25,4 mm aperture EN 15009, Aerosol containers Compartmented aerosol containers EN 15010, Aerosol containers Aluminium containers Tolerances of the fundamental dimensions in connection with the clinch According to the CEN/CENELEC Internal R

18、egulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands

19、, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: Wang Bin, na, Wed Apr 11 02:27:09 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 15006:2006 (E) 4 Introduction The specific dimensions of 25,4 mm aperture aluminium aerosol containers

20、 given in this standard are recognized as being critical in respect of closure efficiency. They are important to the manufacturer in process control and to the filler for incoming goods inspection and ultimately clinch setting and control. Radii and angles in the contact area of the clinch are affec

21、ted by the destructive examination of containers required to check them. Specification of these dimensions has therefore been abandoned in favour of contour definition in terms of inside and outside diameters, contact height, and shoulder height. Licensed Copy: Wang Bin, na, Wed Apr 11 02:27:09 GMT+

22、00:00 2007, Uncontrolled Copy, (c) BSIEN 15006:2006 (E) 5 1 Scope This European Standard specifies the following dimensions of aluminium metal aerosol cans with 25,4 mm aperture: contact height, outside diameter, inside diameter and shoulder height. It is intended to be used with EN 14848 for clinch

23、ing with valve cups. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 14

24、850, Aerosol containers Metal containers with 25,4 mm aperture Measurement of contact height 3 Requirements for specifying and measuring 3.1 Dimensions of the 25,4 mm aperture The dimension of the 25,4 mm aperture shall be as shown in Figure 1. All dimensions in millimetres Key S1Shoulder height h C

25、ontact height Figure 1 Dimensions of the 25,4 mm aperture Licensed Copy: Wang Bin, na, Wed Apr 11 02:27:09 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 15006:2006 (E) 6 NOTE For one piece aluminium containers with a diameter greater than 50 mm, a machined can curl is recommended. 3.2 Contact height

26、NOTE 1 Gauges for the measuring contact height are commercially available. Measure the contact height at 3 equidistant points around the aperture of each test can using the method given in EN 14850. Record the mean value of the contact height (i.e. the arithmetic mean of 3 values), together with max

27、imum and minimum values. NOTE 2 The measuring instrument is commonly rotated around the can aperture for maximum and minimum values. The difference between the 3 values measured on the same can shall not be more than 0,50 mm and the mean value for the batch of cans tested shall be (4,25 0,20) mm. 3.

28、3 Outside diameter Measure the outside diameter at 60 intervals at 3 points around the aperture of each test can. The interval between the 3 values for this can shall not exceed 0,4 mm. The mean value shall be equal to (31,3 0,2) mm. 3.4 Inside diameter Measure the inside diameter at 60 intervals at

29、 3 points around the aperture of each test can. The mean value shall be (25,4 0,1) mm. 3.5 Shoulder height The control of the shoulder height dimension (S1) shall be as specified in Table 1. NOTE This is essential to permit the application of moulded plastic components to the skirt of the valve cup

30、after the can has been closed. Table 1 Shoulder height Dimensions in millimetres Target S1Minimum S15,9 (*)4 (*)Taking into account the future harmonisation of the values at European level. Licensed Copy: Wang Bin, na, Wed Apr 11 02:27:09 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 15006:2006 (E) 7

31、 Bibliography 1 EN 14848, Aerosol containers - Metal containers with 25,4 mm aperture - Dimensions of valve cups Licensed Copy: Wang Bin, na, Wed Apr 11 02:27:09 GMT+00:00 2007, Uncontrolled Copy, (c) BSIBS EN 15006:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the

32、 independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that

33、 they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, th

34、e identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, inter

35、national and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supp

36、ly the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI

37、 electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substant

38、ial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at

39、 http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and

40、Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necess

41、ary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.Licensed Copy: Wang Bin, na, Wed Apr 11 02:27:09 GMT+00:00 2007, Uncontrolled Copy, (c) BSI