BS EN 15007-2017 Aerosol containers Tinplate containers Dimensions of two and three-piece cans《雾化剂罐 马口铁罐 二和三件套罐尺寸规格》.pdf

《BS EN 15007-2017 Aerosol containers Tinplate containers Dimensions of two and three-piece cans《雾化剂罐 马口铁罐 二和三件套罐尺寸规格》.pdf》由会员分享，可在线阅读，更多相关《BS EN 15007-2017 Aerosol containers Tinplate containers Dimensions of two and three-piece cans《雾化剂罐 马口铁罐 二和三件套罐尺寸规格》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、Aerosol containers Tinplate containers Dimensions of two and three-piece cansBS EN 15007:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15007 March 2017 ICS 55.130 Supersedes EN 15007:2006English Version Aeros

2、ol containers - Tinplate containers - Dimensions of two and three-piece cans Rcipients pour arosols - Rcipients en fer-blanc - Dimensions des botiers deux et trois pices Aerosolpackungen - Weiblechbehlter - Mae von zwei- und dreiteiligen Behltern This European Standard was approved by CEN on 7 Febru

3、ary 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obt

4、ained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the C

5、EN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Irelan

6、d, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Manageme

7、nt Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15007:2017 ENational forewordThis British Standard is the UK implementation of EN 15007:2017. It supersedes BS EN 15007:2006 , which

8、is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PKW/0/-/8, Packaging - Metals.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a con

9、tract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 93221 2ICS 55.130Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the auth

10、ority of the Standards Policy and Strategy Committee on 31 July 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 15007:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15007 March 2017 ICS 55.130 Supersedes EN 15007:2006English Version Aerosol contai

11、ners - Tinplate containers - Dimensions of two and three-piece cans Rcipients pour arosols - Rcipients en fer-blanc - Dimensions des botiers deux et trois pices Aerosolpackungen - Weiblechbehlter - Mae von zwei- und dreiteiligen Behltern This European Standard was approved by CEN on 7 February 2017.

12、 CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on

13、application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELE

14、C Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

15、 Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre

16、: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15007:2017 EBS EN 15007:2017EN 15007:2017 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Requirements for dime

17、nsions of the containers . 4 Bibliography 9 BS EN 15007:2017EN 15007:2017 (E) 3 European foreword This document (EN 15007:2017) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national s

18、tandard, either by publication of an identical text or by endorsement, at the latest by September 2017, and conflicting national standards shall be withdrawn at the latest by September 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

19、 rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 15007:2006. This draft European Standard is one of a package of 10 related standards with the following titles: EN 14847, Aerosol containers Tinplate containers Dimensions of the 25,

20、4 mm aperture; EN 14848, Aerosol containers Metal containers with 25,4 mm aperture Dimensions of valve cups; EN 14849, Aerosol containers Glass containers Dimensions of aerosol valve ferrules; EN 14850, Aerosol containers Metal containers with 25,4 mm aperture Measurement of contact height; EN 14854

21、, Aerosol containers Glass containers Dimensions of the neck finish; EN 15006, Metal aerosol containers Aluminium containers Dimensions of the 25,4 mm aperture; EN 15007, Aerosol containers Tinplate containers Dimensions of two and three-piece cans; EN 15008, Aerosol containers Aluminium containers

22、Dimensions of one-piece cans with 25,4 mm aperture; EN 15009, Aerosol containers Compartmented aerosol containers; EN 15010, Aerosol containers Aluminium containers Tolerances of the fundamental dimensions in connection with the clinch. According to the CEN-CENELEC Internal Regulations, the national

23、 standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuan

24、ia, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 15007:2017EN 15007:2017 (E) 4 1 Scope This European Standard specifies the dimensions of two and three-piece tinplate aerosol containers

25、 with nominal brimful capacities. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the refere

26、nced document (including any amendments) applies. EN 14847, Aerosol containers - Tinplate containers - Dimensions of the 25,4 mm aperture 3 Requirements for dimensions of the containers Necked-in containers shall conform to Figure 1 and Table 1. Straight-line containers shall conform to Figure 2 and

27、 Table 2. NOTE The shape of containers need not necessarily correspond exactly to the figures as long as the specified dimensions conform. It is recommended that aerosol containers be designated by: 1) their nominal brimful capacity (C2), in millilitres; 2) their characteristic diameters, in millime

28、tres; 3) their characteristic height (H1), in millimetres. In addition, the nominal diameters of the top and bottom ends for necked-in containers should be included in the designation. EXAMPLES straight-sided cans: C2/D/H1; necked-in cans with different top and bottom diameters: C2/D/DN1/DN2/H1. BS

29、EN 15007:2017EN 15007:2017 (E) 5 Dimensions in millimetres Key 1 aperture (in accordance with EN 14847) Figure 1 Necked-in containers BS EN 15007:2017EN 15007:2017 (E) 6 Table 1 Nominal brimful capacities and dimensions for necked-in containers Brimful capacityaNominal fill Nominal dimensions C2V Bo

30、dy Top end Bottom end liquefied compressed nom min max. gasbgascD DN1DN2H1H2H3D1C H5D2ml ml ml ml ml mm mm mm mm mm mm mm mm mm mm 140 134 146 100 75 45 41 42 96 5,6 101,6 43,6 2,9 5,3 45,2 175 169 181 125 100 45 41 42 118 5,6 123,6 43,6 2,9 5,3 45,2 210 204 216 150 125 45 41 42 140 5,6 145,6 43,6 2

31、,9 5,3 45,2 240 233 247 175 135 45 41 42 158 5,6 163,6 43,6 2,9 5,3 45,2 270 262 278 200 150 45 41 42 178 5,6 183,6 43,6 2,9 5,3 45,2 210 204 216 150 125 49 45 46 or 47d119 7,0 126,0 47,8 2,9 5,5 49,3 270 262 278 200 150 49 45 46 or 47d151 7,0 158,0 47,8 2,9 5,5 49,3 305 297 313 225 175 49 45 46 or

32、47d169 7,0 176,0 47,8 2,9 5,5 49,3 335 325 345 250 200 49 45 46 or 47d185 7,0 192,0 47,8 2,9 5,5 49,3 405 393 417 300 250 49 45 46 or 47d222 7,0 229,0 47,8 2,9 5,5 49,3 140 134 146 100 75 52 48 50 72 8,0 80,0 50,7 3,2 5,6 52,7 175 169 181 125 100 52 48 50 88 8,0 96,0 50,7 3,2 5,6 52,7 210 204 216 15

33、0 125 52 48 50 105 8,0 113,0 50,7 3,2 5,6 52,7 270 262 278 200 150 52 48 50 132 8,0 140,0 50,7 3,2 5,6 52,7 335 325 345 250 200 52 48 50 161 8,0 169,0 50,7 3,2 5,6 52,7 405 393 417 300 250 52 48 50 195 8,0 203,0 50,7 3,2 5,6 52,7 520 507 533 400 300 52 48 50 244 8,0 252,0 50,7 3,2 5,6 52,7 270 262 2

34、78 200 150 57 52 54 110 9,5 119,5 55,5 3,3 6,0 57,6 335 325 345 250 200 57 52 54 136 9,5 145,5 55,5 3,3 6,0 57,6 405 393 417 300 250 57 52 54 164 9,5 173,5 55,5 3,3 6,0 57,6 520 507 533 400 300 57 52 54 207 9,5 216,5 55,5 3,3 6,0 57,6 650 637 663 500 400 57 52 54 257 9,5 266,5 55,5 3,3 6,0 57,6 BS E

35、N 15007:2017EN 15007:2017 (E) 7 Brimful capacityaNominal fill Nominal dimensions C2V Body Top end Bottom end liquefied compressed nom min max. gasbgascD DN1DN2H1H2H3D1C H5D2ml ml ml ml ml mm mm mm mm mm mm mm mm mm mm 405 393 417 300 250 65 60 63 122 13,5 135,5 63,2 3,3 6,3 65,9 520 507 533 400 300

36、65 60 63 157 13,5 170,5 63,2 3,3 6,3 65,9 650 637 663 500 400 65 60 63 195 13,5 208,5 63,2 3,3 6,3 65,9 800 784 816 600 500 65 60 63 240 13,5 253,5 63,2 3,3 6,3 65,9 1 000 980 1 020 750 600 65 60 63 300 13,5 313,5 63,2 3,3 6,3 65,9 aThe minimum and maximum values have been calculated in accordance w

37、ith EN ISO 90-3 1. bProducts propelled by liquefied gas. cProducts propelled by compressed gases alone and products propelled by nitrous oxide or carbon dioxide alone or by mixtures of the two alone when the product has a Bunsen coefficient of 1,2 or less. dDepending on companies. Dimensions in mill

38、imetres Key 1 aperture (in accordance with EN 14847) Figure 2 Straight-sided containers BS EN 15007:2017EN 15007:2017 (E) 8 Table 2 Nominal brimful capacity and dimensions for straight-line containers Brimful capacityaNominal fill Nominal dimensions C2V Top end lique-fied compressed H2H3nom. min. ma

39、x. gasbgascD H1low high low high H4D1D4C ml ml ml ml ml mm mm mm mm mm mm mm mm mm mm 140 134 146 100 75 52 72 9,5 81,5 65 55,5 45,42 3,3 175 169 181 125 100 52 88 9,5 97,5 81 55,5 45,42 3,3 210 204 216 150 125 52 105 9,5 114,5 98 55,5 45,42 3,3 270 262 278 200 150 52 132 9,5 141,5 125 55,5 45,42 3,

40、3 335 325 345 250 200 52 161 9,5 170,5 154 55,5 45,42 3,3 405 393 417 300 250 52 195 9,5 204,5 188 55,5 45,42 3,3 405 393 417 300 250 60 146 13,5 159,5 139 63,2 or 62,8d52,90 3,3 520 507 533 400 300 60 186 13,5 199,5 179 63,2 or 62,8d52,90 3,3 650 637 663 500 400 60 232 13,5 245,5 225 63,2 or 62,8d5

41、2,90 3,3 405 393 417 300 250 65 122 15,5b20,3b137,5 142,3 115 68,5 or 68,7d58,50 3,3 520 507 533 400 300 65 157 15,5b20,3b172,5 177,3 150 68,5 or 68,7d58,50 3,3 650 637 663 500 400 65 195 15,5b20,3b210,5 215,3 188 68,5 or 68,7d58,50 3,3 800 784 816 600 500 65 240 15,5b20,3b255,5 260,3 233 68,5 or 68

42、,7d58,50 3,3 1 000 980 1 020 750 600 65 300 15,5b20,3b315,5 320,3 293 68,5 or 68,7d58,50 3,3 aThe minimum and maximum values have been calculated in accordance with EN ISO 90-3 1. bProducts propelled by liquefied gas. cProducts propelled by compressed gases alone and products propelled by nitrous ox

43、ide or carbon dioxide alone or by mixtures of the two alone when the product has a Bunsen coefficient of 1,2 or less. dDepending on companies. BS EN 15007:2017EN 15007:2017 (E) 9 Bibliography 1 EN ISO 90-3, Light gauge metal containers - Definitions and determination of dimensions and capacities - P

44、art 3: Aerosol cans (ISO 90-3) BS EN 15007:2017This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Stand

45、ards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge

46、embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your

47、 organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards

48、, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including Br

49、itish Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt,