BS EN 14256-2007 Adhesives for non-structural wood applications - Test method and requirements for resistance to static load《非结构用木材粘结剂 耐静荷载的试验方法和要求》.pdf

《BS EN 14256-2007 Adhesives for non-structural wood applications - Test method and requirements for resistance to static load《非结构用木材粘结剂 耐静荷载的试验方法和要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN 14256-2007 Adhesives for non-structural wood applications - Test method and requirements for resistance to static load《非结构用木材粘结剂 耐静荷载的试验方法和要求》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58method and requirements for resistance to static loadThe European Standard EN 14256:2007 has the st

2、atus of a British StandardICS 83.180Adhesives for non-structural wood applications Test BRITISH STANDARDBS EN 14256:2007BS EN 14256:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2007 BSI 2007ISBN 978 0 580 58716 0Amendments is

3、sued since publicationAmd. No. Date CommentsCompliance with a British Standard cannot confer immunity from legal obligations.National forewordThis British Standard is the UK implementation of EN 14256:2007. The UK participation in its preparation was entrusted to Technical Committee PRI/52, Adhesive

4、s.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 14256August

5、 2007ICS 83.180English VersionAdhesives for non-structural wood applications - Test methodand requirements for resistance to static loadAdhsifs pour bois usages non structuraux - Mthodedessai et exigences pour la rsistance la charge statiqueHolzklebstoffe fr nicht tragende Anwendungen -Prfverfahren

6、und Anforderungen an die Bestndigkeitgegen statische BelastungThis European Standard was approved by CEN on 23 June 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without

7、 any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made

8、 by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, G

9、ermany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGM

10、anagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14256:2007: EEN 14256:2007 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Princ

11、iple4 5 Apparatus .5 6 Sample preparation .5 6.1 Preparation of test pieces.5 6.2 Conditioning bonded panels or test pieces7 7 Test procedure.7 8 Calculation and expression of results.7 9 Performance requirements .7 10 Test report 8 10.1 General8 10.2 The adhesive 8 10.3 Preparation of the test piec

12、es and the testing procedures.8 10.4 Test results.8 Bibliography 9 EN 14256:2007 (E) 3 Foreword This document (EN 14256:2007) has been prepared by Technical Committee CEN/TC 193 “Adhesives”, the secretariat of which is held by AENOR. This European Standard shall be given the status of a national sta

13、ndard, either by publication of an identical text or by endorsement, at the latest by February 2008, and conflicting national standards shall be withdrawn at the latest by February 2008. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countrie

14、s are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,

15、Sweden, Switzerland and United Kingdom. EN 14256:2007 (E) 4 Safety statement Persons using this document should be familiar with the normal laboratory practice, if applicable. This document does not purport to address all of the safety problems, if any, associated with its use. It is the responsibil

16、ity of the user to establish appropriate safety and health practices and to ensure compliance with any regulatory conditions. 1 Scope This European Standard specifies a method for determining the ability of a test piece bonded with a thermoplastic adhesive, to support a given load for a specified ti

17、me without fracture or excessive distortion, and specifies performance requirements for mean survival time. It should be used in conjunction with EN 204 and EN 205, which describe durability classes and corresponding test methods for non-structural wood adhesives based on their ability to withstand

18、various water treatments and relatively rapidly applied loads. The test described in this standard may be used to assess joints made with thin glue line, as defined in EN 205. NOTE The test described in this standard is not a mandatory requirement for the classification of adhesives into the classes

19、 D1, D2, D3 and D4 given in EN 204. It is an additional test that can be specified by a purchaser if required. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated reference

20、s, the latest edition of the referenced document (including any amendments) applies. EN 205:2003, Adhesives - Wood adhesives for non-structural applications - Determination of tensile shear strength of lap joints EN 923:2005, Adhesives -Terms and definitions EN 13183-1, Moisture content of a piece o

21、f sawn timber - Part 1: Determination by oven dry method EN 13183-2, Moisture content of a piece of sawn timber - Part 2: Estimation by electrical resistance method 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 923:2005 apply. 4 Principle A number o

22、f test pieces, each incorporating a symmetrical single lap joint between two rectangular wooden adherents, is placed in a jig in a climatically controlled environment. A weight is suspended from the jig applying a constant shear force to each joint for a period of 21 d. The time after which any join

23、t fails is reported. EN 14256:2007 (E) 5 5 Apparatus 5.1 Jigs, for holding the test pieces (see Figure 1). 5.2 Weights, (30,0 0,5) kg with means of attachment to the jigs. 5.3 Enclosure, capable of maintaining the test piece assembly at (23 2) C and (50 5) % relative humidity. 6 Sample preparation 6

24、.1 Preparation of test pieces Prepare 10 test pieces, thin line only, in accordance with 7.1 to 7.2 of EN 205:2003 but with an overlap of (20,0 0,2) mm. A diagram of the test piece is given in Figure 1. EN 14256:2007 (E) 6 All dimensions in millimetres 0,5 unless otherwise stated Key 1 Plywood (5 to

25、 7 ply) 2 Test piece The overlapping dimension l1is (20,0 0,2) mm Figure 1 Jig for assessing the resistance of bonded lap joints to a static load; hanging device made of 5 to 7-ply plywood Make flat-bottomed cuts of (2,5 0,5) mm width in the test pieces across the grain so that an overlap of (20,0 0

26、,2) mm is produced in the middle section, ensuring that cuts just cut through the bond-line but only penetrate as little as possible into the other part of the joint. EN 14256:2007 (E) 7 Apply the adhesive to be tested according to the manufacturer instructions. Where no manufacturer instructions ar

27、e available for the application of the adhesive, use the following bonding procedures: The adhesive application shall be on both sides of the joint. The adhesive spread shall be (150 10) g/m2on each side. The open assembly time shall be (120 10) s. The closed assembly time shall be (180 10) s. The p

28、ressing pressure shall be 0,7 N/mm2 to 1,0 N/mm2. The pressing time shall be minimum of 2 h. 6.2 Conditioning bonded panels or test pieces After bonding and pressing, condition the bonded assemblies or test pieces for a minimum of seven days but not more than eight days in the standard atmosphere th

29、at is to be used for testing, i.e. (23 2) C and (50 5) % relative humidity, 23/50. 7 Test procedure Just after the conditioning period described in 6.2, carry out the test at 23/50, testing 10 test pieces. Mount each test piece in the special jig (5.1) and suspend the jigs vertically. It is permissi

30、ble to suspend one jig from another, up to a maximum of 10. Apply the required load of (30 0,5) kg to the bottom of the jig assembly. Failure is either when the test pieces are broken or when the two jigs are no longer supported by the specimen and they are in contact with each other because of the

31、extent of its deflection. Inspect the test pieces daily, and note the time to failure of each test piece, attributing a survival time, for example, of 3,5 d for test pieces failing between 3 d and 4 d, and 4,5 d for those failing between 4 d and 5 d, etc. Terminate the test after 21 d, or after a me

32、an endurance of 14 d has been achieved, whichever is the sooner. Note the failure in days of each test piece. Standard deviation should be reported in test results. 8 Calculation and expression of results Calculate the mean survival time for the 10 test pieces and report the individual and mean surv

33、ival times. 9 Performance requirements The mean survival time shall not be less than 14 d. EN 14256:2007 (E) 8 10 Test report 10.1 General The items listed in 10.2 to 10.4 shall be recorded in the test report. 10.2 The adhesive a) type and origin of the adhesive; b) batch number or other marking of

34、uniquely identifying the adhesive used; c) number of components and working methods (procedure of preparing and applying of adhesive); d) if known, durability class (for information only). 10.3 Preparation of the test pieces and the testing procedures a) species of wood with botanical name; b) moist

35、ure content of wood relative to oven-dry mass according to EN 13183-1, or the electric method according to EN 13183-2; c) characteristic data relating to the bonding procedure (for instance information about the amount of adhesive applied, the open and closed assembly time, pressing pressure, pressi

36、ng temperature, pressing time); d) special treatment of the surface of the boards to be bonded (e.g. sanding); e) time between the termination of pressing and the cutting of the test pieces; f) number of bonded test pieces. 10.4 Test results a) indication that the test was carried out in accordance

37、with EN 14256; b) mean survival time and individual survival times of the test pieces; c) number of test pieces not failed (unbroken and still supporting the two jigs (see Clause 7) after 21 d loading; d) any deviations from this European Standard; e) date of test. EN 14256:2007 (E) 9 Bibliography 1

38、 EN 204, Classification of thermoplastic wood adhesives for non-structural applications BS EN BSI389 Chiswick High RoadLondonW4 4AL14256:2007BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Euro

39、pe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products

40、 and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI o

41、ffers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax:

42、 +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Informa

43、tion on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the

44、 Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Adminis

45、tration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists

46、in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any mea

47、ns electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.