BS EN 12966-2-2005 Road vertical signs - Variable message traffic signs - Initial type testing《道路垂直标志 可变信息交通标志 初始型式验证》.pdf

《BS EN 12966-2-2005 Road vertical signs - Variable message traffic signs - Initial type testing《道路垂直标志 可变信息交通标志 初始型式验证》.pdf》由会员分享，可在线阅读，更多相关《BS EN 12966-2-2005 Road vertical signs - Variable message traffic signs - Initial type testing《道路垂直标志 可变信息交通标志 初始型式验证》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 12966-2:2005 Road vertical signs Variable message traffic signs Part 2: Initial type testing The European Standard EN 12966-2:2005 has the status of a British Standard ICS 93.080.30 Licensed Copy: Wang Bin, na, Fri Aug 05 06:57:44 BST 2005, Uncontrolled Copy, (c) BSIBS EN 1296

2、6-2:2005 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 6 May 2005 BSI 6 May 2005 ISBN 0 580 45987 X National foreword This British Standard is the official English language version of EN 12966-2:2005. The UK participation in its preparation

3、 was entrusted by Technical Committee B/509, Road equipment, to Subcommittee B/509/3, Construction of road traffic signs, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards whic

4、h implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publicat

5、ion does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/

6、European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page

7、, pages 2 to 12, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments Licensed Copy: Wang Bin, na, Fri Aug 05 06:57:44 BST 2005, Uncontrolled Copy, (c) BSIEUR

8、OPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM EN129662 April2005 ICS93.080.30 Englishversion RoadverticalsignsVariablemessagetrafficsignsPart2: Initialtypetesting SignauxdesignalisationroutireverticalePanneaux messagesvariablesPartie2:Essaidetypeinitial VertikaleVerkehrszeichenWechselverkehrszeichenTe

9、il 2:Erstprfung ThisEuropeanStandardwasapprovedbyCENon15March2005. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnationa

10、l standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheCentralSecretariathasthesamestatusas

11、t heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Slovakia, Slovenia,Spain,Sweden,SwitzerlandandUnited

12、Kingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2005CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.EN129662:2005:E Licensed Copy: Wang Bin, na, Fri Au

13、g 05 06:57:44 BST 2005, Uncontrolled Copy, (c) BSIEN 12966-2:2005 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms, definitions, symbols and abbreviations .4 4 System requirements 5 5 Variable Message Signs6 Annex A (normative) Technical documentation .11 Bibliography 12 Lice

14、nsed Copy: Wang Bin, na, Fri Aug 05 06:57:44 BST 2005, Uncontrolled Copy, (c) BSIEN 12966-2:2005 (E) 3 Foreword This document (EN 12966-2:2005) has been prepared by Technical Committee CEN/TC 226 “Road equipment”, the secretariat of which is held by AFNOR. This European Standard shall be given the s

15、tatus of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2005, and conflicting national standards shall be withdrawn at the latest by October 2005. This document has been prepared under a mandate given to CEN by the European Commission and

16、the European Free Trade Association, and supports essential requirements of EU Directive(s). This document consists of the following Parts under the general title: Road vertical signs - Part 1 : Variable message traffic signs Part 1: Product standard - Part 2 : (this part) Variable message traffic s

17、igns Part 2: Initial type testing - Part 3 : Variable message traffic signs Part 3: Factory production control It derives from performance requirements and test methods published in CEN, CENELEC, CIE and ISO documents together with standards of the CEN member organisations. According to the CEN/CENE

18、LEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malt

19、a, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: Wang Bin, na, Fri Aug 05 06:57:44 BST 2005, Uncontrolled Copy, (c) BSIEN 12966-2:2005 (E) 4 1 Scope This document specifies the requirements for Initial Type Testing (ITT) and

20、is designed to be read in conjunction with Part 1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including

21、any amendments) applies. EN 12767, Passive safety of support structures for road equipment Requirements and test methods EN 12899-1:2001, Fixed, vertical road traffic signs Part 1: Fixed signs EN 12966-1:2005, Road vertical signs Variable message traffic signs Part 1: Product standard EN 50293, Elec

22、tromagnetic compatibility Road traffic signal systems Product standard EN ISO 9000:2000, Quality management systems Fundamentals and vocabulary (ISO 9000:2000) HD 638 S1, Road traffic signal systems HD 60364-4-443, Electrical installation of buildings Part 4-44: Protection for safety Protection agai

23、nst voltage disturbances and electromagnetic disturbances Clause 443: Protection against overvoltages of atmospheric origin or due to switching (IEC 60364-4-44:2001/A1:2003, modified) 3 Terms, definitions, symbols and abbreviations For the purposes of this document, the terms and definitions given i

24、n EN ISO 9000:2000, EN 12966-1:2005 and EN 12899-1:2001 and the following apply. 3.1 initial type testing complete set of tests and other procedures determining the performance of the test module 3.2 manufacturer producer with legal responsibility for placing the product on the market 3.3 supplier p

25、roducer of components (e.g. sign faces, fixing devices, optical devices, luminous sources, etc) for the product 3.4 test module test module is a sample that is representative of the finished product (see EN 12966-1:2005, 9.1) Licensed Copy: Wang Bin, na, Fri Aug 05 06:57:44 BST 2005, Uncontrolled Co

26、py, (c) BSIEN 12966-2:2005 (E) 5 4 System requirements 4.1 General The manufacturer shall demonstrate that characteristics which claim to be pre-tested comply with the requirements of this document. During the Initial Type Testing sequence, if one test fails the manufacturer shall identify the cause

27、 of test failure and the proposed modification to the test module after which the failure within the sequence shall be retested. The technical description, including drawings, shall be as specified in Annex A . Static calculations shall include all fixings and attachments. The conformity of VMS test

28、 module to the requirements of this standard and with the stated values (including classes) shall be demonstrated by initial type testing. NOTE 1 Factory production control by the manufacturer, including product assessment is covered by EN 12966-3. For the purposes of testing, the VMS may be grouped

29、 into families, where it is considered that the selected property/properties is/are common to all VMS within that family. Initial type testing shall be performed to show conformity with this standard on first use of this document for VMS being put onto the market and: - at the beginning of the produ

30、ction of a new or modified VMS design, the raw material or supplier of the components, - at the beginning of a new or modified method of production. In case of type testing on VMS for which initial type testing in accordance with this standard was already performed, type testing may be reduced: - if

31、 it has been established that the performance characteristics compared with the already tested VMS have not been affected, or - in accordance with the rules for grouping and/or direct or extended application of test results. Where components are used whose characteristics have already been determine

32、d by the component manufacturer on the basis of conformity with other technical specifications and will not be adversely affected by the assembly process, these characteristics need not be reassessed (see EN 12966-3) provided that the components performance or method of assessment remain the same. N

33、OTE 2 Products CE marked in accordance with appropriate harmonised European specifications may be presumed to have the performances stated with the CE marking, although this does not replace the responsibility of the component manufacturer to ensure that the product as a whole is correctly designed

34、(where the manufacturer himself undertakes the design) and its components have the necessary performance values to meet the design. 4.2 Characteristics All characteristics in Clauses 7 and 8 of EN 12966-1:2005 shall be subject to initial type testing, with the following exception: - release of dange

35、rous substances may be assessed indirectly by controlling the content of the substance concerned. Licensed Copy: Wang Bin, na, Fri Aug 05 06:57:44 BST 2005, Uncontrolled Copy, (c) BSIEN 12966-2:2005 (E) 6 4.3 Use of historical data Tests previously performed on the same test module in accordance wit

36、h the provisions of this standard (same characteristic(s), test method, sampling procedure, system of attestation of conformity, etc.) may be taken into account. 4.4 Deemed to satisfy provisions and use of reference tabulated data In those cases where conformity with this standard is based on deemed

37、 to satisfy provisions or tabulated values, type testing shall be limited to the verification of whether the test module meets the requirements to use those values, classes or levels, unless better values, classes or levels are being claimed. 4.5 Treatment of calculated values and design In those ca

38、ses where conformity with this standard is based on calculations, type testing will be limited to the verification of the calculations made and that the resulting products correspond to the descriptions/assumptions made in the design and/or calculations. In some cases, the manufacturer may produce p

39、roducts in accordance with a design and/or calculations provided by a third party. In this case, verification will not be of the design or calculations themselves, but only on the fact that the products conform to with the assumptions of the design and/or calculations. 4.6 Technical documentation Te

40、chnical documentation, the characteristics of the VMS and test results shall be kept for 10 years or the period of warranty, which ever is the greater. 5 Variable Message Signs 5.1 Test module The test module is as defined in 9.1 of EN 12966-1:2005. In the case of verification by calculation, of som

41、e characteristics (e.g. deflection), the manufacturer shall also provide relevant drawings, calculations and the technical specifications. This module shall be retained for at least ten years. 5.2 Identification Each module submitted to ITT shall bear a label with at least the information specified

42、in Table 1. Table 1 - Identification label Manufacturer / Site of manufacturer Manufacturing date Relevant classes according to EN 12966-1 ID-number Related technical documentation Licensed Copy: Wang Bin, na, Fri Aug 05 06:57:44 BST 2005, Uncontrolled Copy, (c) BSIEN 12966-2:2005 (E) 7 The related

43、technical documentation shall illustrate the product for which the test module is a replacement, and its characteristics. Each test module submitted to ITT shall be supplied with at least the information as detailed in Annex A (normative). 5.3 Specific requirements The specific requirements shall be

44、 in compliance with EN 12966-1. The characteristics of the test module shall be tested as specified below: - either in column 1 of Table 2 to the requirements of column 2 in Table 2 - or in column 1 of Table 3 to the requirements of column 2 in Table 3 If required, calculations shall be verified. Th

45、e manufacturer shall declare the class or classes to be verified. Licensed Copy: Wang Bin, na, Fri Aug 05 06:57:44 BST 2005, Uncontrolled Copy, (c) BSIEN 12966-2:2005 (E) 8 Table 2 - Characteristics of discontinuous signs Characteristics Applicable Clause(s) of EN 12966-1:2005 Criteria as applicable

46、 General design requirements 5 Provision to retain loose equipment - Manufacturers declaration Materials 6 Appropriate properties - 5.3.5 of EN 12899-1:2001 Environmental stability - Manufacturers declaration Visual performance 7 Colour (chromaticity co-ordinates) 7.2 C1, C2 Luminance 7.3 L1, L2, L3

47、, L3(*), L1(T), L2(T), L3(T) Luminance ratio 7.4 R1, R2, R3 Beam width 7.5 B1, B2, B3, B4, B5, B6, B7 Uniformity 7.6 Pass / Fail Visible flicker 7.7 Pass / Fail Physical performance 8 Environmental requirements 8.2 Temperature 8.2.1 T1, T2, T3 Resistance to pollution 8.2.2 D1, D2, D3, D4 Resistance

48、to corrosion 8.2.3 Pass / Fail Degrees of protection provided by enclosures (IP level) 8.2.4 P1, P2, P3 Structural performance 8.3 Loads 8.3.2.1 5.3.2 of EN 12899-1:2001 Deflections 8.3.2.2 5.3.3 of EN 12899-1:2001 Passive safety 8.3.3 If required by the customer, EN 12767 Impact resistance 8.3.4 Pass / Fail Vibration resistance 8.3.5 Pass / Fail Electrical requirements 8.4 Electrical supply and limits 8.4.1 Pass / Fail Electrical safety 8.4.2 HD 60364-4-443 and HD 638 S1 as applicable Electromagnetic compatibility 8.5 Electromagnetic emissio