BS EN 10140-2006 Cold rolled narrow steel strip - Tolerances on dimensions and shape《冷轧窄钢带 尺寸和形状公差》.pdf

《BS EN 10140-2006 Cold rolled narrow steel strip - Tolerances on dimensions and shape《冷轧窄钢带 尺寸和形状公差》.pdf》由会员分享，可在线阅读，更多相关《BS EN 10140-2006 Cold rolled narrow steel strip - Tolerances on dimensions and shape《冷轧窄钢带 尺寸和形状公差》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58shapeThe European Standard EN 10140:2006 has the status of a British StandardICS 77.140.50Cold roll

2、ed narrow steel strip Tolerances on dimensions and BRITISH STANDARDBS EN10140:2006BS EN 10140:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2006 BSI 2006ISBN 0 580 48669 9Cross-referencesThe British Standards which implement int

3、ernational or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not pur

4、port to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page,

5、 pages 2 to 11 and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsA list of organizations represented on this committee can be obtained on request to its secretary. present to the r

6、esponsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.National forewordThis British Standard is the official English language vers

7、ion of EN 10140:2006. It supersedes BS EN 10140:1997 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee ISE/10, Flat rolled steels products, which has the responsibility to: aid enquirers to understand the text;EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE

8、NORMEN 10140July 2006ICS 77.140.50 Supersedes EN 10140:1996 English VersionCold rolled narrow steel strip - Tolerances on dimensions andshapeFeuillards lamins froid - Tolrances de dimensions et deformeKaltband - Grenzabmae und FormtoleranzenThis European Standard was approved by CEN on 12 June 2006.

9、CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on app

10、lication to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has t

11、he same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,

12、Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwid

13、e for CEN national Members.Ref. No. EN 10140:2006: EEN 10140:2006 (E) 2 Contents Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Form and conditions of delivery 4 4.1 Form of delivery.4 4.2 Condition of delivery .5 5 Designation 5 6 Tolerances on dimensions .6 6.1 Thickness

14、 .6 6.2 Width .6 6.3 Length .7 7 Tolerances on shape .8 7.1 Edge camber 8 7.2 Flatness of cut lengths8 7.3 Out-of-squareness.8 8 Measurements9 8.1 Thickness .9 8.2 Flatness of cut lengths9 8.3 Edge camber 10 9 Packing .10 Bibliography11 EN 10140:2006 (E) 3 Foreword This document (EN 10140:2006) has

15、been prepared by Technical Committee ECISS/TC 13 “Flat products for cold working - Qualities, dimensions, tolerances and specific tests”, the secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by

16、 endorsement, at the latest by January 2007, and conflicting national standards shall be withdrawn at the latest by January 2007. This document supersedes EN 10140:1996. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to im

17、plement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and Uni

18、ted Kingdom. EN 10140:2006 (E) 4 1 Scope 1.1 This European Standard applies to cold rolled narrow strip in coils and cut lengths, in thicknesses up to 10 mm and of widths less than 600 mm, made from unalloyed and alloyed steels, mainly those specified in EN 10132, EN 10139, EN 10268 and prEN 10338,

19、with the exception of stainless and heat-resisting steels and the products given in 1.2. The application of this European Standard to products with other dimensions shall be agreed separately. 1.2 This European Standard does not cover cold rolled flat products for which a separate standard already e

20、xists, particularly the following products: cold rolled non-oriented magnetic steel sheet and strip (EN 10106); grain-oriented magnetic steel sheet and strip (EN 10107); cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state (EN 10341); cold rolled unc

21、oated low carbon and high yield strength steel flat products for cold forming (EN 10131); cold reduced blackplate (EN 10205). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For un

22、dated references the latest edition of the referenced document (including any amendments) applies. EN 10079:1992, Definition of steel products 3 Terms and definitions For the purposes of this European Standard, the terms and definitions of cold rolled flat products given in clause 1 and those given

23、in EN 10079:1992 shall apply. 4 Form and conditions of delivery 4.1 Form of delivery Cold rolled narrow strip according to this European Standard may be supplied: in coils, of which the dimensions and weight shall be agreed at the time of ordering; or in cut lengths (when coils have been unwound and

24、 cut into lengths). By agreement at the time of order, the preferred internal coil diameter is approximately 500 mm or 400 mm. For narrow strip in thicknesses of less than 0,5 mm, smaller internal diameters (e.g. 300 mm or 250 mm) may be agreed separately. NOTE In the case of narrow widths, strip co

25、nforming to this standard may also be wound in layers and supplied in the form of a bobbin wound coil. EN 10140:2006 (E) 5 4.2 Condition of delivery Unless the edge condition and tolerances on dimensions and shape are specified in the order, products shall be supplied with slit edges (GK) and normal

26、 tolerances (A); cut lengths shall be supplied in as produced lengths. 5 Designation Products conforming to this European Standard shall be designated in the following order: a) type of product (narrow strip or cut length); b) reference to this European Standard (EN 10140); c) nominal thickness in m

27、illimetres; d) letters B or C for products ordered with fine or precision tolerances on thickness; e) nominal width in millimetres; f) symbols for type of edge; g) letter B for products ordered with fine tolerances on width; h) nominal length in millimetres (only for cut lengths); i) letter B for pr

28、oducts ordered with fine tolerances on length; j) letters FS for narrow strip or cut length with fine tolerances on edge camber. The designation of products shall be followed by the precise designation of the steel grade ordered and the surface appearance. EXAMPLE 1 The designation for cold rolled n

29、arrow strip conforming to this European Standard, 1,50 mm thick, having a normal tolerance on the nominal thickness, a width of 200 mm, slit edges (GK) and made from steel grade DC04 + LC MB RM conforming to EN 10139, is: Narrow strip EN 10140 - 1,50 x 200 - GK Steel EN 10139 - DC04 + LC - MB - RM E

30、XAMPLE 2 The designation for cut length conforming to this European Standard having a nominal thickness of 2 mm, a nominal width of 450 mm, slit edges (GK), a nominal length equal to 4000 mm with fine tolerances (B) on length and made from steel grade DC03 + A MA conforming to EN 10139, is: Cut leng

31、th EN 10140 - 2,0 x 450 GK x 4000 B Steel EN 10139 - DC03 + A MA EN 10140:2006 (E) 6 6 Tolerances on dimensions 6.1 Thickness 6.1.1 The tolerances on thickness are normal (A), fine (B) or precision (C) and are given in Table 1. Table 1 Tolerance on thickness Dimensions in millimetres Tolerances on t

32、hickness for nominal widths Nominal thickness A B C A B C 0,10 0,008 0,006 0,004 0,010 0,008 0,005 0,10 0,15 0,010 0,008 0,005 0,015 0,012 0,010 0,15 0,25 0,015 0,012 0,008 0,020 0,015 0,010 0,25 0,40 0,020 0,015 0,010 0,025 0,020 0,012 0,40 0,60 0,025 0,020 0,012 0,030 0,025 0,015 0,60 1,00 0,030 0

33、,025 0,015 0,035 0,030 0,020 1,00 1,50 0,035 0,030 0,020 0,040 0,035 0,025 1,50 2,50 0,045 0,035 0,025 0,050 0,040 0,030 2,50 4,00 0,050 0,040 0,030 0,060 0,050 0,035 4,00 6,00 0,060 0,050 0,035 0,070 0,055 0,040 6,00 8,00 0,075 0,060 0,040 0,085 0,065 0,045 8,00 10,00 0,090 0,070 0,045 0,100 0,075

34、0,050 aCan be extended to 650 mm: see 6.2.4. 6.2 Width 6.2.1 The edge condition required (as-rolled, slit or special) shall be agreed at the time of ordering. Unless otherwise specified, products are supplied with slit edges (GK). By special agreement and depending on the technical capabilities of t

35、he manufacturer, flat products may be supplied with special edges (SK), for example sharp-edged or round-edged. 6.2.2 The tolerances on width for narrow strip and cut lengths with as-rolled edges (NK) and slit edges (GK) are given in Tables 2 and 3. By agreement at the time of ordering, slit edged p

36、roducts (GK) may be supplied without minus tolerances (i.e. all plus tolerances) or without plus tolerances (i.e. all minus tolerances) on the nominal width. In this case, the tolerance will be equal to the total range of permissible tolerances given in Tables 2 and 3. 6.2.3 The tolerances on width

37、of products with special edges (SK) shall be agreed at the time of ordering. 6.2.4 The upper limit of 600 mm can be extended to 650 mm by agreement at the time of ordering. EN 10140:2006 (E) 7 Table 2 Tolerance on width for narrow strip with as-rolled edges Dimensions in millimetres Nominal width To

38、lerances on width A B A B A B 0,60 0,15 0,10 0,20 0,13 0,25 0,18 0,60 1,50 0,20 0,13 0,25 0,18 0,30 0,20 1,50 2,50 0,25 0,18 0,30 0,20 0,35 0,25 2,50 4,00 0,30 0,20 0,35 0,25 0,40 0,30 4,00 6,00 0,35 0,25 0,40 0,30 0,45 0,35 6,00 8,00 0,45 0,50 0,55 8,00 10,00 0,50 0,55 0,60 aCan be extended to 650

39、mm: see 6.2.4. NOTE 1 For strip in the hardened and tempered condition, the tolerances on width are to be agreed at the time of ordering. NOTE 2 For thicknesses greater than 6 mm, the measuring method is to be agreed at the time of ordering. 6.3 Length Cut lengths shall be supplied in lengths with a

40、ll plus tolerances as specified in Table 4. Table 4 Length tolerances Dimensions in millimetres Plus tolerances relative to the nominal length for Nominal length L Class A Class B L 1 000 + 10 + 6 1 000 2 500 + 0,01 L + 0,003 L EN 10140:2006 (E) 8 7 Tolerances on shape 7.1 Edge camber Class A and Cl

41、ass B tolerances on edge camber shall be those given in Table 5 for a gauge length of 1000 mm (see also 8.3). Table 5 Tolerance on edge camber Dimensions in millimetres Nominal width W Class A (max. deviation) Class B (FS) (max. deviation) 10 W 25 5,00 2,00 25 W 40 3,50 1,50 40 W 125 2,50 1,25 125 W

42、 600a 2,00 1,00 aCan be extended to 650 mm: see 6.2.4. NOTE 1 The tolerances in Table 5 are only applicable to narrow strip of width at least 10 times the thickness. NOTE 2 For strip in the hardened and tempered condition, edge camber tolerances may be reduced if agreed at the time of ordering. Wher

43、e it is not practicable to measure over 1 000 mm, equivalent tolerances may be calculated from the following formula, the result being rounded to the next highest millimetre Edge camber tolerance=()22length standardlength standardnon edge camber tolerance shown in Table 5 (1) 7.2 Flatness of cut len

44、gths The tolerance on flatness of cut lengths in the direction of rolling shall be 10 mm maximum over 1000 mm. Any other requirements for flatness shall be specially agreed at the time of ordering. If strip is required to be especially flat across the width, the maximum deviation from flatness and t

45、he method of measurement shall be agreed at the time of ordering. 7.3 Out-of-squareness The out-of-squareness of cut lengths in widths less than or equal to 100 mm shall not exceed 1 mm. For cut lengths in widths exceeding 100 mm, the out-of-squareness shall not exceed 1 % of the actual width of the

46、 cut length. EN 10140:2006 (E) 9 8 Measurements 8.1 Thickness The tolerances on thickness given in Table 1 apply only to measurements made at the minimum distances from the edge of the product, as defined in Table 6. Table 6 Minimum distances of the measuring points from the edge Dimensions in milli

47、metres Types of edges Nominal width W Minimum distance of measuring from the edges As rolled edges W 30 30 W 600a 0,5 W 15 Slit edgesb W 20 20 W 600a0,5 W 10 Other edges By agreement aCan be extended to 650 mm: see 6.2.4. bMeasurement throughout the whole width may be performed upon agreement betwee

48、n manufacturer and purchaser. 8.2 Flatness of cut lengths The deviation from flatness, p (in the direction of rolling) is taken to be the greatest distance between the cut length resting freely on a flat horizontal base and a rule. The gauge length is fixed at 1000 mm (see Figure 1). Dimensions in millimetres Key 1 Direction of rolling 2 Product 3 Base p Deviation from flatness Figure 1 Deviation from flatness EN 10140:2006 (E) 10 8.3 Edge camber The edge camber c is taken to be the greatest distance between a longitudinal edge and a straight line connecting both e