BS EN 3717-2008 Aerospace series - Tubes - Selection for engines fluid systems《航空航天系列 管 发动机防冻液系统的选择》.pdf

《BS EN 3717-2008 Aerospace series - Tubes - Selection for engines fluid systems《航空航天系列 管 发动机防冻液系统的选择》.pdf》由会员分享，可在线阅读，更多相关《BS EN 3717-2008 Aerospace series - Tubes - Selection for engines fluid systems《航空航天系列 管 发动机防冻液系统的选择》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 3717:2008Aerospace series Tubes Selection for engines fluid systemsICS 49.080g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58B

2、S EN 3717:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 May 2008 BSI 2008ISBN 978 0 580 62886 3National forewordThis British Standard is the UK implementation of EN 3717:2008.The UK participation in its preparation was entrusted to T

3、echnical Committee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct applic

4、ation.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 3717April 2008ICS 49.080English VersionAerospace series - Tubes - Selection for engines fluid systemsSri

5、e arospatiale - Tubes - Slection pour circuits defluide pour application moteursLuft- und Raumfahrt - Rohre fr Fluid-Systeme anTriebwerken - AuswahlThis European Standard was approved by CEN on 21 December 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate

6、 the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists

7、in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies

8、of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN

9、COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3717:2008: E2 Contents Page Foreword

10、3 1 Scope 4 2 Normative references 4 3 Dimensions.4 BS EN 3717:20083 Foreword This document (EN 3717:2008) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Associat

11、ion, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement,

12、 at the latest by October 2008, and conflicting national standards shall be withdrawn at the latest by October 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying

13、any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hun

14、gary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 3717:20084 1 Scope The present standard gives a selection of external diameters and thicknesses of tubes a

15、ccording to ISO 2964. These tubes shall be used for conveying fluids such as kerosene, oil, air, etc. for engine application. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For un

16、dated references, the latest edition of the referenced document (including any amendments) applies. ISO 2964, Aerospace Tubing Outside diameters and thicknesses Metric dimensions. 3 Dimensions Dimensions are in millimetres. Diameter-thickness combinations of tubes shall be chosen from Table 1. Table

17、 1 Mass a kg/m Thicknesses Stainless steel Titanium alloy Outside diameter 0,6 0,8 1 0,6 0,8 1 4 0,050 0,063 0,074 0,029 0,036 0,042 6 0,080 0,103 0,123 0,046 0,059 0,071 8 0,109 0,142 0,173 0,062 0,081 0,099 10 0,139 0,182 0,222 0,080 0,104 0,127 12 0,169 0,221 0,271 0,097 0,127 0,155 14 0,198 0,26

18、0 0,321 0,114 0,149 0,184 16 0,228 0,300 0,370 0,131 0,172 0,212 18 0,257 0,339 0,419 0,147 0,194 0,240 20 0,287 0,379 0,469 0,165 0,217 0,269 25 0,477 0,592 0,273 0,3332 0,615 0,765 0,35 0,439 40 0,773 0,962 0,443 0,551 45 0,872 1,085 0,500 0,622 50 0,970 1,208 0,556 0,692 aThe masses are given onl

19、y for information. They are calculated on the basis of a density of 7,85 kg/dm3for stainless steel and 4,5 kg/dm3for titanium alloys. BS EN 3717:2008blankBS EN 3717:2008BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparin

20、g British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It

21、is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside fron

22、t cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should

23、be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been p

24、ublished as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available

25、 which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. F

26、or details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available

27、on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stor

28、ed in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.