BS EN 295-4-2013 Vitrified clay pipe systems for drains and sewers Requirements for adaptors connectors and flexible couplings《排水管和下水道用陶土管道系统 接头 连接器和挠性联轴器要求》.pdf

《BS EN 295-4-2013 Vitrified clay pipe systems for drains and sewers Requirements for adaptors connectors and flexible couplings《排水管和下水道用陶土管道系统 接头 连接器和挠性联轴器要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN 295-4-2013 Vitrified clay pipe systems for drains and sewers Requirements for adaptors connectors and flexible couplings《排水管和下水道用陶土管道系统 接头 连接器和挠性联轴器要求》.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 295-4:2013Vitrified clay pipe systems for drains and sewersPart 4: Requirements for adaptors, connectors and flexible couplingsBS EN 295-4:2013 BRITISH STANDARDNational for

2、ewordThis British Standard is the UK implementation of EN 295-4:2013. It supersedes BS EN 295-4:1995 and, together with BS EN 295-1:2013, BS EN 295-2:2013, BS EN 295-5:2013, BS EN 295-6:2013, and BS EN 295-7:2013, it supersedes BS EN 295-10:2005, which is withdrawn.The UK participation in its prepar

3、ation was entrusted to Technical Committee B/505, Wastewater engineering.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct ap

4、plication. The British Standards Institution 2013. Published by BSI Standards Limited 2013.ISBN 978 0 580 70649 3 ICS 23.040.50; 91.140.80; 93.030 Compliance with a British Standard cannot confer immunityfrom legal obligations.This British Standard was published under the authority of the Standards

5、Policy and Strategy Committee on 28 February 2013.Amendments issued since publicationDate Text affectedBS EN 295-4:2013EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 295-4 February 2013 ICS 93.030 Supersedes EN 295-10:2005, EN 295-4:1995English Version Vitrified clay pipe systems for drains an

6、d sewers - Part 4: Requirements for adaptors, connectors and flexible couplings Systmes de tuyaux en grs vitrifi pour les collecteurs dassainissement et les branchements - Partie 4: Exigences applicables aux adaptateurs, raccords et assemblages souples Steinzeugrohrsysteme fr Abwasserleitungen und -

7、knale -Teil 4: Anforderungen an bergangs- und Anschlussbauteile und flexible Kupplungen This European Standard was approved by CEN on 1 December 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status

8、 of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, Germ

9、an). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia

10、, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and Unit

11、ed Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 295-4:2013:

12、EBS EN 295-4:2013 EN 295-4:2013 (E) 2 Contents Page 4 Foreword . . 5 1 Scope . 2 Normative references 5 3 Terms and definitions . 6 4 Symbols and abbreviations 6 5 Requirements for adaptors, connectors and flexible couplings . 6 5.1 Materials, manufacture, water absorption and appearance . . 6 5.1.1

13、 Vitrified clay . 6 5.1.2 Rubber sealing materials 6 5.1.3 Polyurethane sealing materials . 7 5.1.4 Other materials . . 7 7 5.1.5 Manufacture . 5.2 Internal diameter . 7 7 5.3 Length . . 7 5.4 Angles . . 5.5 Squareness of ends and joint interchangeability . 7 5.6 Bond strength of adhesive for fixing

14、 fired vitrified clay parts together 7 7 5.7 Tightness . 5.8 Chemical resistance 7 7 5.8.1 Vitrified clay . 5.8.2 Other materials . . 8 5.9 Requirements for joint assemblies. . 8 5.9.1 Vitrified clay pipeline systems 8 5.9.2 Vitrified clay pipelines to other materials. . 8 5.9.3 Metal banded flexibl

15、e couplings and adaptors . 8 5.9.4 Connectors, insertable fittings and sealing rings . 8 5.9.5 Heatshrinkable sleeves . 8 6 Common requirements for adaptors, connectors and flexible couplings 8 6.1 Reaction to fire . . 8 9 6.2 Durability . 6.3 Dangerous substances . 9 7 Designation . . 9 8 Marking .

16、 . 10 9 Evaluation of conformity . 10 9.1 General . . 10 9.2 Initial type testing . . 10 9.3 Factory production control (FPC) . . 10 Annex A (normative) Metal banded flexible couplings and adaptors . 11 A.1 General . . 11 A.2 Types of metal banded flexible couplings and adaptors . 11 A.2.1 Type 1 co

17、uplings (without shear bands) . 11 A.2.2 Type 2 couplings (with shear bands) . . 11 A.2.3 Metal banded adaptors . 12 A.2.4 Bushes 12 A.3 Requirements . . 12 A.3.1 Materials . . 12 A.3.2 Dimensions and tolerances 13 A.3.3 Performance requirements . 14 BS EN 295-4:2013EN 295-4:2013 (E) 3 A.3.4 Testing

18、 14 Annex B (normative) Connectors, insertable fittings and sealing rings 16 B.1 General . 16 B.2 Connectors . 16 B.3 Insertable fittings . 16 B.4 Sealing rings for cut pipes . 17 B.5 Performance requirements 17 Annex C (normative) Heatshrinkable sleeves 18 C.1 General . 18 C.2 Materials and manufac

19、ture 18 C.3 Dimensions . 19 C.4 Performance requirements 19 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive . 20 ZA.1 Scope and relevant characteristics . 20 ZA.2 Procedures for the attestation of conformity of adaptors, co

20、nnectors and flexible couplings 24 ZA.2.1 System of attestation of conformity 24 ZA.2.2 EC declaration of conformity . 25 ZA.3 CE marking and labelling . 26 ZA.3.1 General . 26 ZA.3.2 CE marking on the product 26 ZA.3.3 CE marking on the accompanying documents . 27 Bibliography 29 4 Foreword This do

21、cument (EN 295-4:2013) has been prepared by Technical Committee CEN/TC 165 “Wastewaterengineering”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identicaltext or by endorsement, at the latest by August 2

22、013, and conflicting national standards shall be withdrawn atthe latest by August 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patentrights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights.

23、 This document supersedes EN 295-4:1995 and together with EN 295-1:2013, EN 295-2:2013,EN 295-5:2013, EN 295-6:2013 and EN 295-7:2013 it supersedes EN 295-10:2005. This document has been prepared under a mandate given to CEN by the European Commission and theEuropean Free Trade Association, and supp

24、orts essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.The main changes with respect to the previous version are listed below: reaction to fire added; Annex ZA added. The standard series EN 295 “Vitr

25、ified clay pipe systems for drains and sewers“ consists of the following parts: Part 1: Requirements for pipes, fittings and joints Part 2: Evaluation of conformity and sampling Part 3: Test methods Part 4: Requirements for adaptors, connectors and flexible couplings (the present document) Part 5: R

26、equirements for perforated pipes and fittings Part 6: Requirements for components of manholes and inspection chambers Part 7: Requirements for pipes and joints for pipe jacking According to the CEN/CENELEC Internal Regulations, the national standards organisations of the followingcountries are bound

27、 to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, CzechRepublic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Ro

28、mania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 295-4:2013 EN 295-4:2013 (E) BS EN 295-4:2013EN 295-4:2013 (E) 5 1 Scope This European Standard specifies requirements for adaptors and connectors made from vitrified clay and/or other suitable materials for

29、use with vitrified clay pipes and fittings for buried drain and sewer systems for the conveyance of wastewater (including domestic wastewater, surface water and rainwater) under gravity and periodic hydraulic surcharge or under continuous low head of pressure. Adaptors and connectors include inserta

30、ble fittings, sealing rings for cut pipes and heat-shrinkable sleeves. This standard also applies for metal banded flexible couplings and adaptors and specifies requirements for rubber, polyurethane, stainless steel and other components used for them. NOTE 1 The specifiers/purchasers can select adap

31、tors, connectors and flexible couplings according to their requirements. NOTE 2 Corresponding provisions for the evaluation of conformity (ITT and FPC) and sampling and those for the test methods are further specified in EN 295-2 and EN 295-3, respectively. 2 Normative references The following docum

32、ents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 295-1:2013, Vitrified c

33、lay pipe systems for drains and sewers Part 1: Requirements for pipes, fittings and joints EN 295-2:2013, Vitrified clay pipe systems for drains and sewers Part 2: Evaluation of conformity and sampling EN 295-3:2012, Vitrified clay pipe systems for drains and sewers Part 3: Test methods EN 295-5:201

34、3, Vitrified clay pipe systems for drains and sewers Part 5: Requirements for perforated pipes and fittings EN 295-6:2013, Vitrified clay pipes systems for drain and sewers Part 6: Requirements for components of manholes and inspection chambers EN 295-7:2013, Vitrified clay pipe systems for drains a

35、nd sewers Part 7: Requirements for pipes and joints for pipe jacking EN 681-1, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber EN 681-4, Elastomeric seals Materials requirements for pipe joint seals used in water and dra

36、inage applications Part 4: Cast polyurethane sealing elements EN 1427, Bitumen and bituminous binders Determination of the softening point Ring and Ball method EN 10088-2:2005, Stainless steels Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes

37、 EN ISO 527-1, Plastics Determination of tensile properties Part 1: General principles (ISO 527-1)EN ISO 527-2, Plastics Determination of tensile properties Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2) 6 EN ISO 868, Plastics and ebonite Determination of indentation hardnes

38、s by means of a durometer (Shorehardness) (ISO 868) EN ISO 1183-1, Plastics Methods for determining the density of non-cellular plastics Part 1: Immersionmethod, liquid pyknometer method and titration method (ISO 1183-1) EN ISO 9445-1:2010, Continuously cold-rolled stainless steel Tolerances on dime

39、nsions and form Part 1: Narrow strip and cut lengths (ISO 9445-1:2009) ISO 3302-1:1996, Rubber Tolerances for products Part 1: Dimensional tolerances ISO 4587, Adhesives Determination of tensile lap-shear strength of rigid-to-rigid bonded assemblies3 Terms and definitions For the purposes of this do

40、cument, the following terms and definitions apply. 3.1 adaptors special items, made from vitrified clay and/or other suitable materials, to join together vitrified clay pipes andfittings of different jointing systems or to join them to items of other pipeline materials 3.2 connectors any special ite

41、m made from vitrified clay and/or other suitable materials for making connections to existingpipe systems, manholes, inspection chambers and building works 3.3 metal banded flexible couplings and adaptors rubber sleeves, with or without rubber bushes or shear bands, with adjustable stainless steel t

42、ension bands bywhich they are secured to the pipe ends 4 Symbols and abbreviations d1pipe inside diameter (mm) d3spigot outside diameter (mm) d4internal diameter of socket or fairing (mm) l2manufacturers stated outside barrel length (mm) OD outside diameter 5 Requirements for adaptors, connectors an

43、d flexible couplings 5.1 Materials, manufacture, water absorption and appearance 5.1.1 Vitrified clay For material, manufacture, water absorption and appearance, all vitrified clay elements of adaptors andconnectors shall comply with EN 295-1:2013, 5.1. 5.1.2 Rubber sealing materials Rubber sealing

44、materials shall comply with EN 681-1. BS EN 295-4:2013 EN 295-4:2013 (E) BS EN 295-4:2013EN 295-4:2013 (E) 7 5.1.3 Polyurethane sealing materials Polyurethane sealing elements shall be in accordance with EN 681-4 for which factory production control shall be in accordance with EN 295-2:2013, 5.3.10.

45、 5.1.4 Other materials All other materials for adaptors and connectors shall comply with the material requirements of A.3.1, C.2, if applicable. Otherwise they shall comply with the declared specification for the material, which shall have requirements for long term behaviour and comply with thermal

46、 cycling stability according to EN 295-1:2013, 6.6 and long term thermal stability according to EN 295-1:2013, 6.7. 5.1.5 Manufacture Adaptors and connectors shall be free from such defects as would impair their function when in service. 5.2 Internal diameter The minimum internal diameter of adaptor

47、s and connectors used with pipes and fittings according to EN 295-1:2013, EN 295-5:2013, EN 295-6:2013 or EN 295-7:2013 shall be as specified in EN 295-1:2013, 5.2. 5.3 Length The nominal length of vitrified clay adaptors and connectors, where appropriate, shall be declared in metres. The length sha

48、ll be measured to the nearest whole millimetre. The tolerance on the declared nominal length shall be from 1 % to + 4 %, or 10 mm, whichever is the larger. 5.4 Angles Adaptors and connectors which include branches shall have preferred nominal angles of 45 and 90. The preferred nominal angle of surfa

49、ce rodding points is 45. The tolerance on the declared angle shall be 5 of the nominal value. 5.5 Squareness of ends and joint interchangeability For adaptors which are straight fittings, the squareness of end shall be in accordance with EN 295-1:2013, 5.4. The joint interchangability of adaptors and connectors to vitrified clay pipelines shall be in accordance with EN 295-1:2013, 6.4. 5.6 Bond strength of adhesive for fixing fired vitrified clay parts together The bond strength of the