BS EN 1097-5-2008 Tests for mechanical and physical properties of aggregates - Part 5 Determination of the water content by drying in a ventilated oven《集料的机械和物理特性试验 第5部分 用通风烘箱干燥法测定.pdf

《BS EN 1097-5-2008 Tests for mechanical and physical properties of aggregates - Part 5 Determination of the water content by drying in a ventilated oven《集料的机械和物理特性试验 第5部分 用通风烘箱干燥法测定.pdf》由会员分享，可在线阅读，更多相关《BS EN 1097-5-2008 Tests for mechanical and physical properties of aggregates - Part 5 Determination of the water content by drying in a ventilated oven《集料的机械和物理特性试验 第5部分 用通风烘箱干燥法测定.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN1097-5:2008ICS 91.100.15NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDTests for mechanicaland physicalproperties ofaggregatesPart 5: Determination of the watercontent by drying in a ventilated ovenLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/

2、10/2009 07:18, Uncontrolled Copy, (c) BSIThis British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June2009 BSI 2009ISBN 978 0 580 58930 0Amendments/corrigenda issued since publicationDate CommentsBS EN 1097-5:2008National forewordThis British Stand

3、ard is the UK implementation of EN 1097-5:2008. It supersedes BS EN 1097-5:1999 which is withdrawn. The UK participation in its preparation was entrusted to TechnicalCommittee B/502/6, Test methods.A list of organizations represented on this committee can be obtained onrequest to its secretary.This

4、publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/10/2009 07:18, Uncontrolled

5、Copy, (c) BSIBS EN 1097-5:2008EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 1097-5March 2008ICS 91.100.15 Supersedes EN 1097-5:1999 English VersionTests for mechanical and physical properties of aggregates -Part 5: Determination of the water content by drying in aventilated ovenEssais pour dterm

6、iner les caractristiques mcaniques etphysiques des granulats - Partie 5: Dtermination de lateneur en eau par schage en tuve ventilePrfverfahren fr mechanische und physikalischeEigenschaften von Gesteinskrnungen - Teil 5:Bestimmung des Wassergehaltes durch OfentrocknungThis European Standard was appr

7、oved by CEN on 4 February 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationals

8、tandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified

9、 to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Ne

10、therlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation

11、in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1097-5:2008: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/10/2009 07:18, Uncontrolled Copy, (c) BSIBS EN 1097-5:2008EN 1097-5:2008 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Term

12、s and definitions .4 4 Principle4 5 Apparatus .5 6 Preparation of test portion5 7 Procedure .6 8 Calculation and expression of results.6 9 Test report.7 Annex A (normative) Variations to the determination of the water content by drying in a ventilated oven for use with lightweight aggregates.8 Annex

13、 B (informative) Example of calculation of the water content by drying in a ventilated oven9 Annex C (informative) Precision 10 Bibliography 11 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/10/2009 07:18, Uncontrolled Copy, (c) BSIBS EN 1097-5:2008EN 1097-5:2008 (E) 3 Foreword This docum

14、ent (EN 1097-5:2008) has been prepared by Technical Committee CEN/TC 154 “Aggregates”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2008, and

15、conflicting national standards shall be withdrawn at the latest by September 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. Thi

16、s document supersedes EN 1097-5:1999. This Standard forms part of a series of tests for mechanical and physical properties of aggregates. Test methods for other properties of aggregates are covered by parts of the following European Standards: EN 932, Tests for general properties of aggregates EN 93

17、3, Tests for geometrical properties of aggregates EN 1367, Tests for thermal and weathering properties of aggregates EN 1744, Tests for chemical properties of aggregates EN 13179, Tests for filler aggregate used in bituminous mixtures The other parts of EN 1097 are: Part 1: Determination of the resi

18、stance to wear (micro-Deval) Part 2: Methods for the determination of resistance to fragmentation Part 3: Determination of loose bulk density and voids Part 4: Determination of the voids of dry compacted filler Part 6: Determination of particle density and water absorption Part 7: Determination of t

19、he particle density of filler - Pyknometer method Part 8: Determination of the polished stone value Part 9: Determination of the resistance to wear by abrasion from studded tyres - Nordic test Part 10: Determination of water suction height According to the CEN/CENELEC Internal Regulations, the natio

20、nal standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, P

21、oland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/10/2009 07:18, Uncontrolled Copy, (c) BSIBS EN 1097-5:2008EN 1097-5:2008 (E) 4 1 Scope This standard describes the reference method used for type

22、 testing and in cases of dispute for the determination of the water content of aggregates by drying in a ventilated oven. For other purposes, in particular factory production control, other methods may be used provided that an appropriate working relationship with the reference method has been estab

23、lished. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 932-2, Tests fo

24、r general properties of aggregates - Part 2: Methods for reducing laboratory samples EN 932-5, Tests for general properties of aggregates - Part 5: Common equipment and calibration 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 aggregate siz

25、e designation of aggregate in terms of lower (d) and upper (D) sieve sizes. This designation accepts the presence of some particles which will be retained on the upper sieve (oversize) and some which will pass the lower sieve (undersize) 3.2 test portion sample used as a whole in a single test 3.3 c

26、onstant mass successive weighings after drying at least 1 h apart not differing by more than 0,1 % NOTE In many cases constant mass can be achieved after a test portion has been dried for a pre-determined period in a specified oven at (110 5) C. Test laboratories can determine the time required to a

27、chieve constant mass for specific types and sizes of sample dependent upon the drying capacity of the oven used. 4 Principle The oven-drying method provides a measure of the total free water present in a test portion of aggregate. The water can be from the surface of the aggregate and from water acc

28、essible pores within the aggregate particles. A test portion is weighed and then placed in a ventilated drying oven at (110 5) C. Successive weighings are used to determine the constant mass of the dried test portion. At all stages of handling and preparation before the start of the test, the labora

29、tory sample and subsequent test portion are protected from loss or gain of water. The water content is determined as the difference in mass between the wet and the dry mass and is expressed as a percentage of the dry mass of the test portion. A variation on the method for use with lightweight aggreg

30、ates is specified in Annex A. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/10/2009 07:18, Uncontrolled Copy, (c) BSIBS EN 1097-5:2008EN 1097-5:2008 (E) 5 5 Apparatus 5.1 All apparatus, unless otherwise stated, shall conform to the general requirements of EN 932-5. 5.2 Container, large e

31、nough to store the test portion before testing. The container shall be non-corrodible and closed so as to prevent the loss of water. NOTE 1 The following may be suitable: a) watch glasses with clips; b) petri dishes or tins with lids; c) plastic sacks or bags with suitable closures; d) buckets with

32、lids. NOTE 2 Long term storage of the test portion in a plastic sack or bag should be avoided. 5.3 Heat resistant stirrer, such as a knife, spatula or a shovel. 5.4 Balance, of suitable capacity, with an accuracy of 0,1 % of the mass of the test portion. 5.5 Ventilated drying oven, thermostatically

33、controlled to maintain a temperature of (110 5) C. NOTE 1 For temperature sensitive aggregates the drying temperature should be reduced to (40 5) C. NOTE 2 The air movements within the oven induced by a ventilation system should not cause the loss of fine particles. 5.6 Desiccator with desiccant. As

34、 an alternative to the desiccator a closed cabinet containing desiccant may be used for the cooling stage. NOTE Silica gel with colour indicator and calcium chloride are suitable desiccants. 5.7 Tray(s), heat resistant and of sufficient size and number to suit the test portion. NOTE For small test p

35、ortions, tins and watch glasses can be suitable. 6 Preparation of test portion The laboratory sample shall be reduced as specified in EN 932-2 to produce a test portion. Calculate the minimum mass of the test portion from the value of the upper (D) sieve size, in millimetres (see 3.1) as follows: -

36、if D 1,0 mm, the minimum mass (in kilograms) shall be 0,2 D; - if D 8 mm the minimum test portion volume shall be 2,0 l; for D 8 mm the minimum test portion volume shall be 1,0 l. A.4 Cooling Instead of cooling the dried test portion to room temperature, weigh each tray and its contents immediately

37、after removing it from the oven. NOTE It can be necessary to protect the balance from the heat of the tray. A cork mat can be suitable. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/10/2009 07:18, Uncontrolled Copy, (c) BSIBS EN 1097-5:2008EN 1097-5:2008 (E) 9 Annex B (informative) Examp

38、le of calculation of the water content by drying in a ventilated oven Table B.1 Determination of the water content by drying in a ventilated oven (using one tray) 1 Container M2653,34 g 2 Mass of tray + moist test portion M1 + M23 574,4 g 3 Mass of tray + dry test portion Md1 + M23 389,7 g 4 Second

39、weighing of tray and dry test portion Mdi+ M23 388,6 g 5 Difference of weighing data (line 3 - line 4) 1,1 g 6 (line 3 - line 4) x 100 (line 3 - line 1) 0,04 % (see note) 7 Mass of water (line 2 - line 4) (M1 + M2) - (M3 + M2) 185,8 g 8 Mass of dry test portion (line 4 - line 1) M32 735,2 g 9 Water

40、content (line 7) x 100 (line 8) (mass %) 6,8 % NOTE In line 6, 0,04 % is less than 0,1 %. Additional weighing is not required and Mdibecomes M3because constant mass has been achieved. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/10/2009 07:18, Uncontrolled Copy, (c) BSIBS EN 1097-5:2008

41、EN 1097-5:2008 (E) 10 Annex C (informative) Precision A precision exercise was carried out in 1988 in the United Kingdom involving 13 laboratories. The results of the exercise obtained by applying the oven dried method once to a single test portion were: Repeatability r1= 0,11 + 0,079 X where X is t

42、he mean value of the water content. Definitions of r1and X are given in EN 932-6. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 14/10/2009 07:18, Uncontrolled Copy, (c) BSIBS EN 1097-5:2008EN 1097-5:2008 (E) 11 Bibliography 1 EN 932-6, Tests for general properties of aggregates - Part 6: De

43、finitions of repeatability and reproducibility 2 ISO 6783:1982, Coarse aggregates for concrete - Determination of particle density and water absorption - Hydrostatic balance method 3 BS 812:Part 109:1990, Testing aggregates - Part 109: Methods for determination of moisture content Licensed Copy: Wan

44、g Bin, ISO/EXCHANGE CHINA STANDARDS, 14/10/2009 07:18, Uncontrolled Copy, (c) BSIBS EN1097-5:2008BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing Brit

45、ishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the con

46、stant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:

47、+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to

48、Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published a

49、s British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kep