BS DD IEC TS 61994-4-3-2008 Piezoelectric and dielectric devices for frequency control and selection - Glossary - Materials - Materials for dielectric devices《频率控制和选择用压电器件与介质器件 术语表.pdf

《BS DD IEC TS 61994-4-3-2008 Piezoelectric and dielectric devices for frequency control and selection - Glossary - Materials - Materials for dielectric devices《频率控制和选择用压电器件与介质器件 术语表.pdf》由会员分享，可在线阅读，更多相关《BS DD IEC TS 61994-4-3-2008 Piezoelectric and dielectric devices for frequency control and selection - Glossary - Materials - Materials for dielectric devices《频率控制和选择用压电器件与介质器件 术语表.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、DRAFT FOR DEVELOPMENTDD IEC/TS 61994-4-3:2008Piezoelectric and dielectric devices for frequency control and selection Glossary Part 4-3: Materials Materials for dielectric devicesICS 31.140g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g5

2、1g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58DD IEC/TS 61994-4-3:2008This Draft for Development was published under the authority of the Standards Policy and Strategy Committee on 30 May 2008 BSI 2008ISBN 978 0 580 63060 6National forewordThis Draft for De

3、velopment is the UK implementation of IEC/TS 61994-4-3:2008. This publication is not to be regarded as a British Standard.It is being issued in the Draft for Development series of publications and is of a provisional nature. It should be applied on this provisional basis, so that information and exp

4、erience of its practical application can be obtained.Comments arising from the use of this Draft for Development are requested so that UK experience can be reported to the international organization responsible for its conversion to an international standard. A review of this publication will be ini

5、tiated not later than three years after its publication by the international organization so that a decision can be taken on its status. Notification of the start of the review period will be made in an announcement in the appropriate issue of Update Standards.According to the replies received by th

6、e end of the review period, the responsible BSI Committee will decide whether to support the conversion into an international Standard, to extend the life of the Technical Specification or to withdraw it. Comments should be sent to the Secretary of the responsible BSI Technical Committee at British

7、Standards House, 389 Chiswick High Road, London W4 4AL.The UK participation in its preparation was entrusted to Technical Committee EPL/49, Piezoelectric devices for frequency control and selection.A list of organizations represented on this committee can be obtained on request to its secretary.This

8、 publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Amendments/corrigenda issued since publicationDate CommentsIEC/TS 61994-4-3Edition 1.0 2008-02TECHNICAL SPECIFICATIONPiezoelectric and dielectric devices for frequen

9、cy control and selection Glossary Part 4-3: Materials Materials for dielectric devices DD IEC/TS 61994-4-3:2008PIEZOELECTRIC AND DIELECTRIC DEVICES FOR FREQUENCY CONTROL AND SELECTION GLOSSARY Part 4-3: Materials Materials for dielectric devices 1 Scope This part of IEC 61994 specifies the terms and

10、 definitions for materials applied for devices using waveguide type dielectric resonators representing the state-of-the-art, which are intended for use in the standards and documents of IEC TC 49. 2 Normative references The following referenced documents are indispensable for the application of this

11、 document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61338-1: 2004, Waveguide type dielectric resonators Part 1: Generic specification 3 Terms and definitions For the purposes of

12、 this document, the terms and definitions of IEC 61338-1 apply, notably the following. 3.1 dielectric material material which predominantly exhibit dielectric properties IEC 61338-1 3.2 dielectric resonator material dielectric materials defined to be used for resonator application at high frequency,

13、 i.e. UHF or SHF range. The dielectric material is required to have high relative permittivity, a low loss factor and a minimal temperature coefficient of permittivity IEC 61338-1 3.3 electric constant 0 constant equal to 8,85421012AsV1m1, defined by the permittivity of vacuum IEC 61338-1 3.4 relati

14、ve permittivity r absolute permittivity of a material or medium divided by the electric constant 0 DD IEC/TS 61994-4-3:2008 2 NOTE The complex relative permittivity r is defined as “r j= , )(r Re= , )(“r Im= where is usually called dielectric constant; “ corresponds to the dielectric loss of the mat

15、erial. IEC 61338-1 3.5 absolute permittivity quantity which when multiplied by the electric field strength E is equal to the electric flux density D ED = , r0 = IEC 61338-1 3.6 loss angle phase displacement between the component of the electric flux density and the electric field strength IEC 61338-

16、1 3.7 loss factor tangent of the loss angle /“tan = NOTE The loss factor can be determined by the ratio of the negative part to the real part of the complex relative permittivity. IEC 61338-1 3.8 quality factor of a material 0Q reciprocal of the tangent of the loss angle tan/1“/0=Q NOTE The quality

17、factor of a material is also defined as 2 times the ratio of the stored electromagnetic energy to the energy dissipated in the material per cycle. It is frequency dependent. IEC 61338-1 3.9 temperature coefficient of permittivity TC fractional change of permittivity due to a change in temperature di

18、vided by the change in temperature DD IEC/TS 61994-4-3:2008 3 6refrefref10)(=TTTCT 1 106/K where T is the permittivity at temperature T ; ref is the permittivity at reference temperature refT . IEC 61338-1 3.10 coefficient of linear thermal expansion fractional change of dimension due to a change in

19、 temperature divided by the change in temperature 6refrefref10)(=TTlllT 1106/K where Tl is the dimension at temperature T ; refl is the dimension at reference temperature refT . IEC 61338-1 3.11 dielectric resonator resonator using dielectrics with a high dielectric constant and the structure of whi

20、ch is a dielectric waveguide of finite length NOTE The dielectric resonators in use are always shielded with conductors. IEC 61338-1 3.12 dielectric support element supporting a dielectric resonator. The support is generally used for TE01mode resonators and has a low dielectric constant IEC 61338-1

21、_ DD IEC/TS 61994-4-3:2008 4 blankDD IEC/TS 61994-4-3:2008BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incor

22、porated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone

23、finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service c

24、alled PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Stand

25、ards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of

26、information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111.

27、 Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0

28、)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the co

29、pyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or othe

30、rwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.