BS 8532-2011 Terminal units for high flow anaesthetic gas scavenging systems Specification for probes and type-specific connection points《高流量麻醉气体清除终端设备 探头和形态特异接头的规范》.pdf

《BS 8532-2011 Terminal units for high flow anaesthetic gas scavenging systems Specification for probes and type-specific connection points《高流量麻醉气体清除终端设备 探头和形态特异接头的规范》.pdf》由会员分享，可在线阅读，更多相关《BS 8532-2011 Terminal units for high flow anaesthetic gas scavenging systems Specification for probes and type-specific connection points《高流量麻醉气体清除终端设备 探头和形态特异接头的规范》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationTerminal units for high flow anaesthetic gas scavenging systems Specification for probes and type-specific connection pointsBS 8532:2011BS 8532:2011 BRITISH STANDARDPublishing an

2、d copyright informationThe BSI copyright notice displayed in this document indicates when the document was last issued. BSI 2011ISBN 978 0 580 67853 0ICS 11.040.10The following BSI references relate to the work on this standard: Committee reference CH/121/6 Draft for comment 09/30203720 DCPublicatio

3、n historyFirst published, March 2011Amendments issued since publicationDate Text affected BSI 2011 iBS 8532:2011BRITISH STANDARDContentsForeword ii1 Scope 12 Normative references 13 Terms and definitions 14 General requirements 15 Dimensions of probe and type-specific connection point 16 Marking, co

4、lour coding and packaging 17 Information to be supplied by the manufacturer 2List of figuresFigure 1 Dimensions of probe, nut and O ring 3Figure 2 Dimensions of type-specific connection point 6Summary of pagesThis document comprises a front cover, an inside front cover, pages i to ii, pages 1 to 6,

5、an inside back cover and a back cover.BS 8532:2011ii BSI 2011BRITISH STANDARDForewordPublishing informationThis British Standard is published by BSI and came into effect on 31 March 2011. It was prepared by Subcommittee CH/121/6, Medical gas supply systems, under the authority of Technical Committee

6、 CH/121, Anaesthetic and respiratory equipment. A list of organizations represented on these committees can be obtained on request to their secretary.Relationship with other publicationsTerminal units for anaesthetic gas scavenging systems are specified in BS EN ISO 9170-2, which was written with th

7、e intention that national standards would be in place to specify the dimensions of the terminal units for high flow gas scavenging systems. Such high flow systems are standard in the UK and the dimensions were previously given in BS 6834 which was withdrawn on publication of BS EN 737-4:1998, and wh

8、ich in turn has been superseded by BS EN ISO 9170-2. This British Standard has been prepared to specify the dimensions of the probes and type-specific connection points for terminal units for these systems.Presentational conventionsThe provisions of this standard are presented in roman (i.e. upright

9、) type. Its requirements are expressed in sentences in which the principal auxiliary verb is “shall”.Commentary, explanation and general informative material is presented in smaller italic type, and does not constitute a normative element.Contractual and legal considerationsThis publication does not

10、 purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations. BSI 2011 1BS 8532:2011BRITISH STANDARD1 ScopeThis British Standard specifies the dimensions for probes a

11、nd type-specific connection points for terminal units for high flow anaesthetic gas scavenging systems (AGSS).2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references,

12、 the latest edition of the referenced document (including any amendments) applies.BS 3643-1:2007, ISO metric screw threads Part 1: Principles and basic dataBS 3643-2:2007, ISO metric screw threads Part 2: Specification for selected limits of sizeBS EN ISO 9170-2:2008, Terminal units for medical gas

13、pipeline systems Part 2: Terminal units for anaesthetic gas scavenging systems3 Terms and definitionsFor the purposes of this British Standard the terms and definitions given in BS EN ISO 9170-2:2008 apply.4 General requirementsThe safety, materials, design and construction of the terminal unit shal

14、l be in accordance with BS EN ISO 9170-2:2008.5 Dimensions of probe and type-specific connection pointThe dimensions of the probe and the type-specific connection point shall be as shown in Figure 1 and Figure 2, respectively.6 Marking, colour coding and packaging6.1 MarkingMarking shall be in accor

15、dance with BS EN ISO 9170-2:2008.In addition, the marking shall include the number and date of this British Standard, i.e. BS 8532:2011 1).1)Marking BS 8532:2011 on or in relation to a product represents a manufacturers declaration of conformity, i.e. a claim by or on behalf of the manufacturer that

16、 the product meets the requirements of the standard. The accuracy of the claim is solely the claimants responsibility. Such a declaration is not to be confused with third-party certification of conformity.BS 8532:20112 BSI 2011BRITISH STANDARD6.2 Colour codingThe type-specific connection point shall

17、 be colour coded. The colour shall be divided into quadrants, coloured alternately blue (RAL 5010) and yellow (RAL 1018).6.3 PackagingPackaging shall be in accordance with BS EN ISO 9170-2:2008.7 Information to be supplied by the manufacturerThe information to be supplied by the manufacturer shall b

18、e in accordance with BS EN ISO 9170-2:2008. BSI 2011 3BS 8532:2011BRITISH STANDARDFigure 1Dimensions of probe, nut and O ringLinear dimensions in millimetresa) AGSS probeBS 8532:20114 BSI 2011BRITISH STANDARDFigure 1Dimensions of probe, nut and O ring(continued)Linear dimensions in millimetresKey 1

19、Outside diameter may be varied and should be knurled, fluted or similar to provide a grip for hand tightening only2 Marking in accordance with 6.1shall be stamped on the outside diameterb) Nut for AGSS probe BSI 2011 5BS 8532:2011BRITISH STANDARDFigure 1Dimensions of probe, nut and O ring(continued)

20、Linear dimensions in millimetresc) O ring for AGSS probed) Complete AGSS probe assemblyBS 8532:20116 BSI 2011BRITISH STANDARDFigure 2Dimensions of type-specific connection pointLinear dimensions in millimetresThis page deliberately left blankBSI is the independent national body responsible for prepa

21、ring British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswic

22、k High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices.

23、We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an in

24、dividual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the

25、website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that ha

26、ve been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information

27、services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and

28、 other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI pu

29、blications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic

30、, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: