BS 7959-2-2000 Materials used for the control of liquid spillages - Determination of water repellency or buoyancy for hydrophobic (oil sorbent) materials《控制液体溢溅用材料 疏水材料(油吸附剂)的水排斥性或.pdf

《BS 7959-2-2000 Materials used for the control of liquid spillages - Determination of water repellency or buoyancy for hydrophobic (oil sorbent) materials《控制液体溢溅用材料 疏水材料(油吸附剂)的水排斥性或.pdf》由会员分享，可在线阅读，更多相关《BS 7959-2-2000 Materials used for the control of liquid spillages - Determination of water repellency or buoyancy for hydrophobic (oil sorbent) materials《控制液体溢溅用材料 疏水材料(油吸附剂)的水排斥性或.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS 7959-2:2000 ICS 13.020

2、.40; 71.100.99; 75.180.99 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Materials used for the control of liquid spillages Part 2: Determination of water repellency or buoyancy for hydrophobic (oil sorbent) materialsThis British Standard, having been prepared under the direc

3、tion of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 March 2000 BSI 03-2000 The following BSI references relate to the work on this standard: Committee reference CII/63 Draft for Comment 98/124920 DC ISBN 0

4、 580 33100 8 BS 7959-2:2000 Amendments issued since publication Amd. No. Date Comments Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technical Committee CII/63, Chemical spill control, upon which the following bodies were represented: AEA

5、Technology British Oils Spill Control Association British Safety Industry Federation Chemical Industries Association Environment Agency Fire Service College Personal Safety Manufacturers AssociationBS 7959-2:2000 BSI 03-2000 i Contents Page Committees responsible Inside front cover Foreword ii 1 Sco

6、pe 1 2 Normative references 1 3 Terms and definitions 1 4 Sampling and preparation of test samples 1 5 Determination of water repellency 1ii BSI 03-2000 BS 7959-2:2000 Foreword This British Standard has been prepared by Technical Committee CII/63, Chemical spill control. BS 7959-2 gives a method for

7、 the determination of water repellency (buoyancy) for hydrophobic materials used for the control of spilled liquids. General test methods for all materials used for the control of spilled liquids are given in BS 7959-1. These materials, which are generically known as “sorbents”, include those which

8、act by adsorption, absorption and gelling. The test methods generally apply to sorbents of all types, which allows user to make reliable comparisons between materials of different types for specific applications. A British Standard does not purport to include all the necessary provisions of a contra

9、ct. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 2, an inside back cove

10、r and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. BSI 03-2000 1 BS 7959-2:2000 1 Scope This part of BS 7959-2 describes methods of sampling and determining the water repellency of materials for the control of oil spills on water. Suc

11、h materials are hydrophobic in nature (i.e. reject water), and they retain their buoyancy for sufficient time to allow use on water. A variety of materials of different composition and format is used in this application and for the purposes of this standard has been divided into the following catego

12、ries. Type I web type sheet, pad or roll Type II loose material discrete particles of variable size Type III filled products socks, booms, pillows, cushions Type IV agglomerates masses of strands for pick-up of viscous liquids 2 Normative references The following normative documents contain provisio

13、ns which, through reference in this text, constitute provisions of this British Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. For undated references the latest edition of the publication referred to applies. BS 7959-1, Materials us

14、ed for the control of liquid spillages Part 1: Determination of sorbency. 3 Terms and definitions For the purposes of this part of BS 7959 the terms and definitions given in BS 7959-1 and the following apply. 3.1 water repellency property of hydrophobic materials whereby they reject adsorption of wa

15、ter when subjected to gentle agitation 3.2 buoyancy ability to spring readily to the surface of water and/or float on the water surface, not below or at the water surface 4 Sampling and preparation of test samples Take representative samples of the materials as described in BS 7959-1:2000, 4.1. Prep

16、are and condition the material as described in BS 7959-1:2000, 4.2. 5 Determination of water repellency 5.1 Principle A small sample of material is placed on the surface of water in a test tank. Signs of “water logging” or sinking are assessed after a fixed time on the water, and after agitation for

17、 some materials. NOTE This method of test is a qualitative determination of suitability of hydrophobic sorbents for use on water. 5.2 Reagents Clean tap water, free from detergents, emulsifying agents and surfactants. 5.3 Apparatus All apparatus shall be completely free of detergents, surfactants, e

18、mulsifying agents and other materials. 5.3.1 Ordinary laboratory apparatus. 5.3.2 Test vessel, constructed of glass or clear plastic, of suitable size to allow sample to: a) float freely on the surface; b) absorb its maximum volume of water; c) sink to its full depth. 5.4 Procedure 5.4.1 Test pieces

19、 Prepare the test pieces as follows. For Type 1 cut a sample of size suitable to cover the surface of the water in the test vessel. For Type II measure out sufficient volume of loose material to cover the entire surface area of the liquid to about 10 mm thickness. For Types II and IV use the sample

20、as described in clause 4. Where feasible use a full-size product sample. 5.4.2 Test liquid Start each test with fresh water (5.2) to avoid any surface effects due to contamination of the water. 5.4.3 Determination For all types, place the sample of sorbent material on the surface of the water. In th

21、e case of Type II, loose materials, spread the sample evenly to a thickness of about 10 mm. Leave the sample to stand for 30 min and then agitate with a glass rod for 30 s. NOTE A 1 l glass beaker may be the most appropriate vessel for Type II evaluation.2 BSI 03-2000 BS 7959-2:2000 For all types, t

22、he samples shall be observed for a minimum of 8 h. During the test period, the test sample shall be examined for signs of sinking, water logging or significant loss of buoyancy. If any of these physical changes occurs within 8 hours the product shall be deemed to have failed the test. NOTE 2 For som

23、e products, failure may occur in the very early part of the test. The test may be continued for whatever time is considered necessary for product end use. 5.5 Test report The test report should include the following minimum information: a) material description and BS material type; b) supplier/manuf

24、acturer and product code; c) date of test; d) reference to this British Standard; e) observations during test; f) result of test (pass/fail) after 8 hours; g) time to failure if it fails after 8 hour test.blankBS 7959-2:2000 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | |

25、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsib

26、le for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendment

27、s or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found

28、on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publication

29、s should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI pr

30、ovides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Te

31、l: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Co

32、pyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitte

33、d in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.