BS 4737-3 8-1978 Intruder alarm systems - Specifications for components - Volumetric capacitive detectors《擅入者报警系统 元部件规范 第8节 电容式形体探测器》.pdf

《BS 4737-3 8-1978 Intruder alarm systems - Specifications for components - Volumetric capacitive detectors《擅入者报警系统 元部件规范 第8节 电容式形体探测器》.pdf》由会员分享，可在线阅读，更多相关《BS 4737-3 8-1978 Intruder alarm systems - Specifications for components - Volumetric capacitive detectors《擅入者报警系统 元部件规范 第8节 电容式形体探测器》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 4737-3.8: 1978 (Reprinted, incorporating Amendment No. 1) Specification for Intruder alarm systems in buildings Part 3: Requirements for detection devices Section 3.8 Volumetric capacitive detectors UDC 696.6:654.924.3:621.3.013.72BS 4737-3.8:1978 This British Standard, having be

2、en prepared under the direction of the Electronic Equipment Standards Committee, was published under the authority of the Executive Board on 29 December 1978 BSI 12-1998 First published April 1971 Firstrevision December 1978 The following BSI references relate to the work on this standard: Committee

3、 reference EEL/27 Draft for comment 74/25543 DC ISBN 0 580 10359 5 Cooperating organizations The Electronic Equipment Standards Committee, under whose direction this British Standard was prepared, consists of representatives from the following Government department and scientific and industrial orga

4、nizations: British Broadcasting Corporation British Electrical and Allied Manufacturers Association British Radio Equipment Manufacturers Association Cable Television Association of Great Britain Department of Prices and Consumer Protection Electrical, Electronic, Telecommunication and Plumbing Unio

5、n Electricity Supply Industry in England and Wales Electronic Components Board Electronic Engineering Association * Engineering Equipment Users Association Institution of Electronic and Radio Engineers Post Office * Radio and Electronic Component Manufacturers Federation Scientific Instrument Manufa

6、cturers Association The organizations marked with an asterisk in the above list, together with the following, were directly represented on the committee entrusted with the preparation of this British Standard: Association of Burglary Insurance Surveyors Association of Chief Police Officers British I

7、nsurance Association British Railways Board British Security Industry Association Department of the Environment Home Office Independent Burglar Alarm Association Lloyds Syndicates Survey Department Metropolitan Police Ministry of Defence National Supervisory Council for Intruder Alarms Telecommunica

8、tion Engineering and Manufacturing Association The Committee of London Clearing Bankers on behalf of the Committee of Scottish Clearing Bankers, Co-operative Bank, Central Trustee Savings Bank and Yorkshire Bank Amendments issued since publication Amd. No. Date of issue Comments 3252 March 1980 Indi

9、cated by a sideline in the marginBS 4737-3.8:1978 BSI 12-1998 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 References 1 3 Definition 1 4 Area or volume of coverage 1 5 Test period 1 6 Power supply 1 7 Environment 1 8 Interference 1 9 Housing 1 10 Marking 1 Standa

10、rds Publications referred to Inside back coverBS 4737-3.8:1978 ii BSI 12-1998 Foreword This revision of BS 4737 has been prepared under the direction of the Electronic Equipment Standards Committee to reflect the technical advances in the industry since the publication of the 1971 edition. It takes

11、account of AmendmentNo. 1, 1972 (AMD 1064) and of Amendment No. 2, 1973 (AMD 1218). It is being published in a number of separate Sections, as follows. Part 1: Requirements for systems with audible signalling only; 1.1: Installation; 1.2: Maintenance and records; Part 2: Requirements for systems wit

12、h remote signalling; 2.1: Installation; 2.2: Maintenance and records; Part 3: Requirements for detection devices, consisting of a number of separate Sections (3.1 to 3.14). The specifications for detection devices (including this Section of BS 4737) are to be read in conjunction with Section 1.1 or

13、Section 2.1, as appropriate. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of p

14、ages This document comprises a front cover, an inside front cover, pages i and ii, pages1and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside front cover.

15、BS 4737-3.8:1978 BSI 12-1998 1 1 Scope This British Standard specifies the general requirements for volumetric capacitive detectors to be used in intruder alarm systems in buildings. 2 References The titles of the standards publications referred to in this standard are listed on the inside back cove

16、r. 3 Definition For the purposes of this British Standard, the following definition applies in addition to those given in BS4737-1.1 and/or BS4737-2.1. volumetric capacitive detector a detection device designed to generate an alarm condition in response to the change (or rate of change) in capacitan

17、ce when a person enters and moves in the area or volume of coverage 4 Area or volume of coverage 4.1 The area or volume of coverage of the detector is that area or volume within which the entry and movement of a 60 20kg person walking at any speed between 0.3m/s and 0.6m/s through a distance of 2m c

18、auses the detector to generate an alarm condition or to signal to a processing device. The installer shall identify the area or volume of coverage in the equipment record (see7.1 of BS 4737-2.2:1977). NOTEIt should be recognized that the area or volume effectively protected by the device may extend

19、beyond the stated area or volume of coverage as a result of the judicious siting of the detector in relation to points of entry to the premises. Alteration of the position of objects within the area or volume of coverage may cause significant changes in the area or volume protected. 4.2 A method of

20、indication shall be provided to enable the subscriber to check the area or volume of coverage before the system is closed. 5 Test period Except when immediate connection is needed for urgent security reasons, or when the detector replaces a similar existing unit, the detector shall not be connected

21、to an alarm system which is extended to the police until the detector has operated in the installation for at least 7 days without generating an unwanted alarm. 6 Power supply An alarm condition shall be generated if the voltage of the power supply to the detector is reduced sufficiently to impair t

22、he performance of the detector. 7 Environment The requirements of this British Standard shall be met by the detector under any combination of the following environmental conditions. 8 Interference The detector shall be adequately protected against any externally-generated radio-frequency interferenc

23、e and/or mains-borne interference which may normally be expected to occur within the working environment. 9 Housing The detector (except the sensor itself) and any processing device shall be housed in one or more containers. It shall not be possible to open the container(s) by the normal means of ac

24、cess without operating an anti-tamper device. If the equipment is housed in separate containers, the inter-connection(s) shall be electrically protected. Any means for adjusting the equipment shall be enclosed within the container(s). 10 Marking Text deleted. Temperature: 0 C to 40 C Relative humidi

25、ty: 10 % to 90 %blankBS 4737-3.8:1978 BSI 12-1998 Standards publications referred to BS 4737, Specification for intruder alarm systems in buildings. BS 4737-1, Requirements for systems with audible signalling only. BS 4737-1.1, Installation. BS 4737-1.2, Maintenance and records 1) . BS 4737-2, Requi

26、rements for systems with remote signalling. BS 4737-2.1, Installation. BS 4737-2.2, Maintenance and records. BS 4737-3, Requirements for detection devices 1) . BS 4737-3.1, Continuous wiring. BS 4737-3.2, Foil on glass. BS 4737-3.3, Protective switches. BS 4737-3.4, Radiowave Doppler detectors. BS 4

27、737-3.5, Ultrasonic movement detectors. BS 4737-3.6, Acoustic detectors. BS 4737-3.7, Passive infra-red detectors. BS 4737-3.9, Pressure mats. BS 4737-3.10, Vibration detectors. BS 4737-3.11, Rigid printed-circuit wiring. BS 4737-3.12, Beam interruption detectors. BS 4737-3.13, Capacitive proximity

28、detectors. BS 4737-3.14, Deliberately-operated devices. 1) Referred to in the foreword only.BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

29、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated

30、 by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone find

31、ing an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS whic

32、h ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards

33、, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Ex

34、porters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substant

35、ial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international

36、 standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does n

37、ot preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.