BS 1139-1 2-1990 Metal scaffolding - Tubes - Specification for aluminium tube《金属脚手架 第1部分 管 第2节 铝管规范》.pdf

《BS 1139-1 2-1990 Metal scaffolding - Tubes - Specification for aluminium tube《金属脚手架 第1部分 管 第2节 铝管规范》.pdf》由会员分享，可在线阅读，更多相关《BS 1139-1 2-1990 Metal scaffolding - Tubes - Specification for aluminium tube《金属脚手架 第1部分 管 第2节 铝管规范》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 1139-1.2: 1990 Metal scaffolding Part 1: Tubes Section 1.2 Specification for aluminium tubeBS1139-1.2:1990 This British Standard, having been prepared under the directionof the Civil Engineeringand Building Structures Standards Policy Committee, waspublished underthe authorityof

2、the Boardof BSI andcomes into effect on 31October 1990 BSI 02-1999 First published as BS 1139 November 1943 Second edition November 1951 Third edition June 1964 Fourth edition as BS 1139-1 April1982 Fifth edition as BS 1139-1.2 October 1990 The following BSI references relate to the work on this sta

3、ndard: Committee reference CSB/57 Draft for comment 87/15200 DC ISBN 0 580 18471 4 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Civil Engineering and Building Structures Standards Policy Committee (CSB/-) to Technical Committee CSB/57

4、, upon which the following bodies were represented: Association of Consulting Engineers Association of Consulting Scientists British Constructional Steelwork Association Ltd. British Steel Industry Building Employers Confederation Concrete Society Construction Health and Safety Group Construction In

5、dustry Training Board Department of the Environment (Property Services Agency) Electricity Supply Industry in England and Wales Engineering Equipment and Materials Users Association English Net Manufacturers Association Federation of Civil Engineering Contractors Health and Safety Executive Institut

6、e of Building Control Institution of Civil Engineers Institution of Structural Engineers National Association of Formwork Contractors National Association of Scaffolding Contractors National Federation of Master Steeplejacks and Lightning Conductor Engineers Prefabricated Aluminium Scaffolding Manuf

7、acturers Association Suspended Access Equipment Manufacturers Association Amendments issued since publication Amd. No. Date of issue CommentsBS1139-1.2:1990 BSI 02-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 Method of manufacture 1 3 Materials 1 4 Dimension

8、s and tolerances 1 5 Workmanship 1 6 Finish 1 7 Identification 1 Appendix A Drift expanding test for extruded aluminium scaffold tubes 2 Figure 1 Arrangement of drift expanding test 2 Table 1 Dimensions and tolerances for aluminium tubes 1 Publications referred to Inside back coverBS1139-1.2:1990 ii

9、 BSI 02-1999 Foreword This Section of BS1139 has been prepared under the direction of the Civil Engineering and Building Structures Standards Policy Committee. Together with Section1.1, it supersedes BS1139-1:1982, which is withdrawn. This Section of BS1139 is one of a series specifying requirements

10、 for the design, construction and testing of equipment for use in scaffolding and other temporary structures. It specifies requirements for aluminium tubing of the type traditionally used in tube and fitting scaffolding. The need for this new edition arose because of the advent of European proposals

11、 covering steel scaffold tube, whereas any such action for aluminium tubes is further away. Steel tubing is now covered in BS1139-1.1. This Section retains the style and technical content of the 1982 edition, and is substantially the same as the 1964 version. The separate Parts and Sections are as f

12、ollows. Part 1: Tubes; Section 1.1: Specification for steel tubes; Section 1.2: Specification for aluminium tube; Part 2: Couplers; Section 2.1: Specification for steel couplers, loose spigots and base plates for use in working scaffolds and falsework made of steel tubes (IdenticalwithEN74); Section

13、 2.2 1) : Specification for aluminium couplers, fittings and accessories for use in tubular scaffolding; Part 3: Specification for prefabricated access and working towers; Part 4: Specification for prefabricated steel splitheads and trestles; Part 5 2) : Specification for materials, dimensions, desi

14、gn loads and safety requirements for service and working scaffolds made of prefabricated elements. (Identical with HD 1000) A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance

15、with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages1and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had a

16、mendments incorporated. This will be indicated in the amendment table on theinside front cover. 1) In preparation: it will cover fittings not included in Section 2.1. Additional couplers have not yet been harmonized. 2) In preparation.BS1139-1.2:1990 BSI 02-1999 1 1 Scope This Section of BS 1139 spe

17、cifies requirements for the material, dimensions and method of manufacture of extruded aluminium tubes for use in scaffolding. It specifies one grade of material and one range of dimensions. Appendix A describes a drift expanding test for extruded aluminium scaffold tubes. NOTEThe titles of the publ

18、ications referred to in this standard are listed on the inside back cover. 2 Method of manufacture Aluminium scaffold tubes shall be produced by extrusion, e.g. by means of a process using a mandrel, a bridge die or a porthole. When tested in accordance with Appendix A, a tube in its finished state

19、shall show no sign of an unsound weld. NOTEA tube with faulty welding will tend to exhibit a straight line, rather than jagged, fracture at the position of the weld. This test procedure should be considered as being a part of a quality control programme and the frequency of testing should be such as

20、 to ensure adequate quality control. 3 Materials 3.1 General The tube shall be manufactured from aluminium complying with the requirements of 3.2 and 3.3. 3.2 Chemical composition Tubes shall be extruded aluminium tubes complying with the requirements for alloy 6082-TF (formerly HE30-TF) as specifie

21、d in BS1474. NOTEAs these tubes are heat-treated, heat should not be applied to them by welding, flame cutting, etc., unless this is carried out under the controlled conditions recommended in CP118. 3.3 Mechanical properties The mechanical properties of the tubes shall be as follows: 4 Dimensions an

22、d tolerances The dimensions and tolerances for aluminium tubes shall be as given in Table 1. Table 1 Dimensions and tolerances for aluminium tubes NOTEThe following nominal values for the properties of aluminium scaffolding tubes of the dimensions in Table 1 are given for information purposes only.

23、Details of maximum permissible stresses are given in BS 5973. 5 Workmanship A tube shall not deviate from a straight line by more than 1/600 of its length, measured at the centre of the length. Tubes shall be clean and free from detrimental defects. The ends shall be cut cleanly and square with the

24、axis of the tube. 6 Finish Tubes shall be mill finished, i.e. without any surface treatment. NOTEFor all normal purposes no painting or other surface treatment is required. Tubes likely to remain in contact with wet acid or alkaline materials, e.g.damp cement or lime renderings, need protection. Adv

25、ice on suitable coatings can be obtained from the Aluminium Federation 3) . 7 Identification The method of identification used shall not impair the performance of the tube. tensile strength (R m ) 295 N/mm 2min. yield strength (R e ) (0.2%proof stress) 255 N/mm 2min. elongation (A) on a gauge length

26、, L o , of 50 mm 7 % min. Dimensions and mass Tolerance Outside diameter 48.30 mm 0.5 mm Thickness 4.47 mm 0.56 mm Nominal mass per unit length 1.667 kg/m (48.30 mm 4.47 mm) Single tube max. reduction 7.5 % Quantities of 150 m and over 5% Length if specified exact 6.0 mm Symbol Value Cross-sectional

27、 area A 6.15 cm 2 Second moment of area I 14.9 cm 4 Elastic modulus Z 6.18 cm 3 Radius of gyration r 1.56 cm 3) Aluminium Federation Ltd., Broadway House, Calthorpe Road, Five Ways, Birmingham, B15 1TN.BS1139-1.2:1990 2 BSI 02-1999 Appendix A Drift expanding test for extruded aluminium scaffold tube

28、s A.1 Principle The end of a tube or test piece is expanded using a conical mandrel until it tears or splits. The test is carried out at ambient temperature unless otherwise specified. A.2 Apparatus A.2.1 Polished steel conical mandrel, of adequate hardness and having a conical included angle of30,4

29、5 or 60. A.3 Test piece The test piece shall consist of a piece of tube having a length equal to at least twice the external diameter of the tube. Both ends of the test piece shall be plane and perpendicular to the axis of the tube. The test piece shall be cleaned to remove any loose chips or dirt f

30、rom the inside surface. NOTEThe end to be tested is normally rounded by filing. However, a test piece with edges that have not been rounded is acceptable provided that the test result is satisfactory. A.4 Procedure Lubricate the mandrel so that it does not rotate in relation to the tube during the t

31、est. Force the conical mandrel under pressure into the open end of the test piece, so that the axis of the cone coincides with the axis of the test piece. Continue applying pressure until the tube tears or splits. Figure 1 Arrangement of drift expandingtestBS1139-1.2:1990 BSI 02-1999 Publications re

32、ferred to BS 1474, Specification for wrought aluminium and aluminium alloys for general engineering purposes:bars, extruded round tubes and sections. BS 5973, Code of practice for access and working scaffolds and special scaffold structures in steel. CP 118, The structural use of aluminium. BSI 389

33、Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British S

34、tandards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of Britis

35、h Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the t

36、echnical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards

37、Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Sta

38、ndards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details o

39、n all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Me

40、mbership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no ex

41、tract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as s

42、ymbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.