ASTM G35-1998(2010) Standard Practice for Determining the Susceptibility of Stainless Steels and Related Nickel-Chromium-Iron Alloys to Stress-Corrosion Cracking in Polythionic Aci.pdf

《ASTM G35-1998(2010) Standard Practice for Determining the Susceptibility of Stainless Steels and Related Nickel-Chromium-Iron Alloys to Stress-Corrosion Cracking in Polythionic Aci.pdf》由会员分享，可在线阅读，更多相关《ASTM G35-1998(2010) Standard Practice for Determining the Susceptibility of Stainless Steels and Related Nickel-Chromium-Iron Alloys to Stress-Corrosion Cracking in Polythionic Aci.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: G35 98 (Reapproved 2010)Standard Practice forDetermining the Susceptibility of Stainless Steels andRelated Nickel-Chromium-Iron Alloys to Stress-CorrosionCracking in Polythionic Acids1This standard is issued under the fixed designation G35; the number immediately following the designati

2、on indicates the year of originaladoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers procedures for

3、 preparing and con-ducting the polythionic acid test at room temperature, 22 to25C (72 to 77F), to determine the relative susceptibility ofstainless steels or other related materials (nickel-chromiumironalloys) to intergranular stress corrosion cracking.1.2 This practice can be used to evaluate stai

4、nless steels orother materials in the “as received” condition or after beingsubjected to high-temperature service, 482 to 815C (900 to1500F), for prolonged periods of time.1.3 This practice can be applied to wrought products,castings, and weld metal of stainless steels or other relatedmaterials to b

5、e used in environments containing sulfur orsulfides. Other materials capable of being sensitized can alsobe tested in accordance with this test.1.4 This practice may be used with a variety of stresscorrosion test specimens, surface finishes, and methods ofapplying stress.1.5 This standard does not p

6、urport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. For more specificprecautionary statements,

7、 see Section 7.2. Referenced Documents2.1 ASTM Standards:2D1193 Specification for Reagent WaterG1 Practice for Preparing, Cleaning, and Evaluating Corro-sion Test SpecimensG15 Terminology Relating to Corrosion and CorrosionTesting3G30 Practice for Making and Using U-Bend Stress-Corrosion Test Specim

8、ens3. Summary of Practice3.1 The stressed specimens are placed in the container alongwith a sensitized and stressed AISI Type 302 (UNS S30200) orType 304 (UNS S30400) stainless steel control specimen. Asufficient amount of the previously prepared polythionic acidsolution is added to the container to

9、 immerse the test speci-mens. A cover is placed on the container and the test is carriedout at room temperature.4. Significance and Use4.1 This environment provides a way of evaluating theresistance of stainless steels and related alloys to intergranularstress corrosion cracking. Failure is accelera

10、ted by the presenceof increasing amounts of intergranular precipitate. Results forthe polythionic acid test have not been correlated exactly withthose of intergranular corrosion tests.Also, this test may not berelevant to stress corrosion cracking in chlorides or causticenvironments.4.2 The polythio

11、nic acid environment may produce areas ofshallow intergranular attack in addition to the more localizedand deeper cracking mode of attack. Examination of failedspecimens is necessary to confirm that failure occurred bycracking rather than mechanical failure of reduced sections.5. Apparatus5.1 Any su

12、itable glass or other transparent, inert containercan be used to contain the acid solution and stressed specimensduring the period of test at room temperature, 22 to 25C (721This practice is under the jurisdiction of ASTM Committee G01 on Corrosionof Metals and is the direct responsibility of Subcom

13、mittee G01.06 on Environmen-tally Assisted Cracking.Current edition approved Sept. 1, 2010. Published November 2010. Originallyapproved in 1988. Last previous edition approved in 2004 as G3598(2004). DOI:10.1520/G0035-98R10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcont

14、act ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn. The last approved version of this historical standard is referencedon www.astm.org.1Copyright ASTM International, 100 Barr Ha

15、rbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.to 77F). The container should be fitted with a removable topto reduce evaporation and to allow access to the stressedspecimen (or specimens) for the periodic inspection.6. Reagents6.1 Purity of ReagentsThe polythionic acid solu

16、tion shallbe prepared using reagent grade sulfurous acid and technicalgrade hydrogen sulfide; or, distilled water, commercial gradesulfur dioxide, and technical grade hydrogen sulfide.6.2 Purity of WaterReagent water Type IV (SpecificationD1193) shall be used to prepare the test solutions.6.3 Wacken

17、roders or Polythionic Acid Solution (1)4Aslow current of hydrogen sulfide is passed for an hour througha fritted glass tube into a flask containing chilled (0C, 32F)6 % sulfurous acid, after which the liquid is kept in thestoppered flask for 48 h at room temperature. This operation isrepeated until

18、the liquid no longer gives off the odor of sulfurdioxide after standing at room temperature for a few hours.Note safety precautions in Section 7.6.3.1 In an alternative method (2), the polythionic acidsolution is prepared by passing a slow current of sulfur dioxidegas through a fritted glass bubbler

19、 submerged in a container ofdistilled water. This is continued until the solution becomessaturated and then the hydrogen sulfide gas is slowly bubbledinto the sulfurous acid solution.6.3.2 The presence of polythionic acids in the solutionprepared in accordance with 6.3 or 6.3.1 can be checked byeith

20、er of the following methods. Polarography (3) can beemployed to identify the thionic acids, or the percent of acidpresent in the solution can be determined by wet techniques(4). The simplest method of checking the solution for poly-thionic acids is to expose a stressed and sensitized sample ofAISI T

21、ype 302 stainless steel. The sample should fail bycracking in less than 1 h.Alternatively, Type 304 sheet (0.07 %carbon) which has been sensitized and exposed as a U-bendshould crack in 1 h (5). Detection of cracks can be facilitatedby closing the legs of the U-bend and examining with a 203binocular

22、 microscope.7. Safety Precautions7.1 Hydrogen sulfide should be handled with extreme cau-tion. The characteristic odor of hydrogen sulfide cannot alwaysbe used as an alarm system because the olfactory nervesbecome deadened when exposed to a concentration of a fewparts per million of this gas. The ma

23、ximum allowable concen-tration in the air for an 8-h work day is 10 ppm, which is wellabove the level detectable by smell. Exposure to high concen-trations of hydrogen sulfide can be fatal. For additionalinformation on the toxicity of hydrogen sulfide, consult Ref(6).7.2 Normal laboratory precaution

24、s should be observed whenhandling the sulfurous or polythionic acid solutions. Hydrogensulfide should only be used in a hood observing the aboveprecautions.8. Test Specimens8.1 Any type of stress corrosion test specimen can be usedwith this test solution. For a comprehensive discussion of thevarious

25、 types of test specimens available, see Ref (7), as wellas Practices G1 and G30, and Terminology G15.8.2 The AISI Type 302 control specimens should be sensi-tized by heating in a furnace for 4 h at 650C (1200F) andthen allowing to air cool. TheAISI Type 304 control specimensshould be sensitized by h

26、eating in a furnace for2hat677C(1250F) and then allowing to air cool.9. Procedure9.1 Prepare the polythionic acid test solution as described in6.3 and 6.3.1.9.2 Prior to usage, filter the acid solution to remove theexcess sulfur and test for the presence of polythionic acids. Thesimplest method of t

27、esting for the acid is to expose a stressedspecimen of sensitized AISI Type 302 or Type 304 stainlesssteel. The specimen should fail by cracking in less than 1 h.9.3 Place the stressed specimens in the container along withthe sensitized and stressedAISI Type 302 or Type 304 stainlesssteel control sa

28、mple. Add a sufficient amount of polythionicacid solution to the container to immerse the test specimens.Close the container and carry out the test at room temperature.Record starting time for the test.10. Report10.1 Record starting time, type of specimen, stress, and typeof exposure. A distinction

29、must be made in the type ofexposure; that is, complete immersion, vapor phase exposure,or a combination of immersion and vapor phase. The timerequired to initiate cracks, the rate of crack growth, and time tofailure may be of importance, depending upon the purpose ofthe test.10.1.1 Periodic removal

30、of specimens from the solutionmay be necessary to determine the time when cracks firstappear and the rate of crack propagation. Microscopicalexamination of polished surfaces is required to detect crackinitiation. All stressed surfaces should be examined at magni-fications up to 203 at the completion

31、 of this test. Metallo-graphic examination of exposed surfaces and of polished andetched cross sections at higher magnifications are necessary toestablish the type of cracking.10.1.2 Ruptured specimens should also be examined forevidence of mechanical failure resulting from the action ofapplied stre

32、ss on specimens whose cross sections have beenreduced by general or pitting corrosion or both. Such failuresusually show evidence of ductility. Duplicate tests with thickerspecimens should be made in cases of doubt.11. Keywords11.1 accelerated test; nickel-chromium-iron alloys; poly-thionic acids; s

33、tainless steels; stress-corrosion cracking4The boldface numbers in parentheses refer to a list of references at the end ofthis standard.G35 98 (2010)2REFERENCES(1) Debus, H., “Chemical Investigation of Wackenroders Solution,”Journal of the Chemical Society, London, Transactions, Vol 53, 1888,p. 278

34、(paper XXV).(2) Samans, C. H., “Stress Corrosion Cracking Susceptibility of StainlessSteels and Nickel-Base Alloys in Polythionic Acids and Acid CopperSulfate Solution,” Corrosion, Vol 20, August 1964, pp. 256t262t.(3) Murayama, T., “Polarography of Polythionates,” Journal of ChemicalSociety of Japa

35、n, Pure Chemistry Section, Vol 74, No. 5, 1953, pp.349352.(4) Jay, P. R., “Determination of Polythionic Acids,” Analytical Chemis-try, Vol 25, No. 2, 1953, pp. 288290.(5) Crum, J. R., Adkins, M. E., and Lipscomb, W. G., “Performance ofHigh Nickel Alloys in Refinery and Petrochemical Environments,”Ma

36、terials Performance, Vol. 25, No. 7, July, 1986, pp. 2733.(6) Chemical Safety Data Sheet SD-36, Manufacturing Chemists Asso-ciation, 1825 Connecticut Ave., N.W., Washington, DC 20009.(7) “Stress Corrosion Testing Methods,” Stress Corrosion Testing,ASTMSTP 425, ASTM Testing Mats. (Out of print. Send

37、orders directly toUniversity Microfilms, Inc., 300 North Zeeb Rd., Ann Arbor, MI48106.)ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of

38、the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Y

39、our comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your commen

40、ts have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or mu

41、ltiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).G35 98 (2010)3