ASTM F2822-2010 Standard Specification for Fixed Anchorages Installed on Structures used for Rope Rescue Training《绳索救援训练用结构物上安装式固定锚点的标准规范》.pdf
《ASTM F2822-2010 Standard Specification for Fixed Anchorages Installed on Structures used for Rope Rescue Training《绳索救援训练用结构物上安装式固定锚点的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM F2822-2010 Standard Specification for Fixed Anchorages Installed on Structures used for Rope Rescue Training《绳索救援训练用结构物上安装式固定锚点的标准规范》.pdf(2页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F2822 10Standard Specification forFixed Anchorages Installed on Structures used for RopeRescue Training1This standard is issued under the fixed designation F2822; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the yea
2、r of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This standard specifies the minimum strength require-ments for anchorages permanently installed or attached totra
3、ining towers or other structures used for rope rescuetraining. It does not describe how those anchorages areconstructed, installed in, or attached to the structure nor does itinclude any factors of safety. It only specifies the design loadsthat must be considered.1.2 The values stated in SI units ar
4、e to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices
5、 and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2F2266 Specification for Masses Used in Testing RescueSystems and Components3. Terminology3.1 Definitions of Terms Specific to This Standard:3.2 anchorage, na permanently attached point
6、 on thestructure that is used as an attachment for rope or hardware.Also referred to as an anchor.3.3 failure, nthe point at which some part of the anchorphysically distorts or begins to detach from its mounting pointon the structure.3.4 proof load, na predetermined test load, greater thanthe servic
7、e load, to which a specimen is subjected beforeacceptance for use. In this standard the proof load is twice themaximum anticipated load on an anchor.4. Performance Requirements4.1 Each anchorage shall be designed to hold a minimum of40 kN in all directions of potential loading.5. Other Requirements5
8、.1 The anchorage shall be manufactured in such a way thata carabiner with a gate opening of 25 mm or greater shall fitaround it and the gate shall be able to close and lock.5.2 The anchorage shall be constructed using rounded stockor with beveled or chamfered edges to minimize damage tohardware, rop
9、e, or webbing that is attached to the anchorage.TEST METHODS6. Scope6.1 This test method provides basic testing procedures forproduct acceptance. It is a nondestructive “proof load” test andtherefore is not a test of ultimate load-carrying capacity of theanchor.7. Significance and Use7.1 This test v
10、erifies that a carabiner can be attached to theanchorage and that the anchorage will hold a minimum oftwice the anticipated load.8. Hazards8.1 The anchorage, attaching carabiners, or rope could failand eject parts. The test load or testing machine could fall. Usea safety screen, protective eyewear,
11、do not increase the testload any greater than necessary, and do not perform this testalone.9. Procedure9.1 Attach the testing device to the anchorage using acarabiner that has a gate opening of 25 mm or greater and astrength of at least 40 kN.9.2 Subject the anchorage to a force of 10.88 kN in thedi
12、rection of anticipated loading, maintain the force for oneminute then remove the force.9.3 Repeat the test specified above, altering the direction ofanchorage loading, until the anchorage has been tested in alldirections of anticipated use.1This test method is under the jurisdiction of ASTM Committe
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF28222010STANDARDSPECIFICATIONFORFIXEDANCHORAGESINSTALLEDONSTRUCTURESUSEDFORROPERESCUETRAINING 绳索

链接地址:http://www.mydoc123.com/p-539541.html