ASTM F2277-2012 Standard Test Methods for Evaluating Design and Performance Characteristics of Selectorized Strength Equipment《评估可调节健身器材设计和性能特点的标准试验方法》.pdf

《ASTM F2277-2012 Standard Test Methods for Evaluating Design and Performance Characteristics of Selectorized Strength Equipment《评估可调节健身器材设计和性能特点的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM F2277-2012 Standard Test Methods for Evaluating Design and Performance Characteristics of Selectorized Strength Equipment《评估可调节健身器材设计和性能特点的标准试验方法》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、Designation:F227703 (Reapproved 2010) Designation: F2277 12An American National StandardStandard Test Methods forEvaluating Design and Performance Characteristics ofSelectorized Strength Equipment1This standard is issued under the fixed designation F2277; the number immediately following the designa

2、tion indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONThe goal of these test methods is

3、 to provide reliable and repeatable methods for the evaluation ofselectorized strength equipment. Users of these machines must recognize, however, that conformanceto a standard will not necessarily prevent injuries. Like other physical activities, exercise involvingstrength equipment involves the ri

4、sk of injury, particularly if the equipment is not maintained or usedproperly.1. Scope1.1 These test methods specify procedures and apparatus used for testing and evaluating selectorized strength equipment forcompliance to Specification F2216. Both design and operational parameters will be evaluated

5、. Where possible and applicable,accepted test methods from other recognized bodies will be used and referenced.1.2 RequirementsSelectorized strength equipment is to be tested for all of the following parameters: Selectorized strengthequipment is to be tested in accordance with these test methods or

6、Test Methods F2571 for all of the following parameters:1.2.1 Stability,1.2.2 Edge and corner sharpness,1.2.3 Tube ends,1.2.4 Weight stack travel,1.2.5 Weight stack selector pin retention,1.2.6 Function of adjustments and locking mechanisms,1.2.7 Handgrip design and retention,1.2.8 Assist mechanisms,

7、1.2.9 Foot supports,1.2.10 Rope and belt systems:1.2.10.1 Static load,1.2.10.2 End fitting design,1.2.11 Chain drive design,1.2.12 Pulley design:1.2.12.1 Rope pulley design,1.2.12.2 Belt pulley design,1.2.13 Entrapment zones,1.2.14 Pull in points,1.2.15 Weight stack enclosure design,1.2.16 Loading a

8、nd deflection:1.2.16.1 Intrinsic loading and associated deflection,1.2.16.2 Extrinsic loading and associated deflection,1.2.16.3 Endurance loading, and1.2.17 Documentation and warnings verification.1This test method is under the jurisdiction ofASTM Committee F08 on Sports Equipment and Facilities an

9、d is the direct responsibility of Subcommittee F08.30 on FitnessProducts.Current edition approved Feb. 1, 2010. Published May 2010. Originally approved in 2003. Last previous edition approved in 2003 as F227703. DOI:10.1520/F2277-03R10.Current edition approved March 1, 2012. Published March 2012. Or

10、iginally approved in 2003. Last previous edition approved in 2010 as F2277 03 (2010). DOI:10.1520/F2277-12.1This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be te

11、chnically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, P

12、O Box C700, West Conshohocken, PA 19428-2959, United States.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicabi

13、lity of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:2F963Consumer Safety Specification for Toy SafetyF1749 Specification for Fitness Equipment and Fitness Facility Safety Signage and LabelsF2216 Specification for Selectorized Strength Equipment Specification for Sele

14、ctorized Strength EquipmentF2571 Test Methods for Evaluating Design and Performance Characteristics of Fitness Equipment2.2 European Standards:EN 9571Stationary Training EquipmentPart 1: General Safety Requirements and Test Methods3EN 9572Stationary Training EquipmentPart 2: Strength Training Equipm

15、ent, Additional Specific Safety Requirements andTest Methods32.3 UL Standard:UL 1439UL Standard for Safety Tests for Sharpness of Edges on Equipment2.4 ANSI Standard:ANSI B29.1Precision Power Transmission Roller Chains, Attachments and SprocketsEN 957-1 Stationary Training EquipmentPart 1: General S

16、afety Requirements and Test Methods3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 normal operation, nthe operation of the selectorized strength equipment as defined by the manufacturer.4. Significance and Use4.1 The purpose of these test methods is to provide valid and repeat

17、able test methods for the evaluation of selectorized strengthequipment assembled and maintained according to the manufacturers specifications. Use of these test methods in conjunction withSpecification F2216 is intended to maximize the reliability of selectorized strength equipment design and reduce

18、 the risk of seriousinjury resulting from design deficiencies.5. Certification5.1 These test methods permit self-certification. It is recommended that each manufacturer employ an independent laboratoryto evaluate and validate that their designs and test procedures conform and comply to these test me

19、thods and Specification F2216.6. Units of Measure6.1 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.7. Sample Preparation7.1 Assemble and adjust the selectorized strength equipment according to the manufacturers instructions. Remo

20、ve upholsteredpads from the sample. On machines that are fully assembled, verify according to the manufacturers instructions that allcomponents are functioning and that they have been adjusted and aligned properly. Unless otherwise stated, the machine must passthe tests without adjustment from this

21、initial condition. Selectorized strength equipment shall be provided with the largest weightstack offered by the manufacturer for the model to be tested.7.2 The individual test methods will describe any variations or modifications that are required to the test sample.8. Test Methods and Procedures8.

22、1 Stability:8.1.1 Selectorized strength equipment shall be tested with and without the simulated user load in the orientation that is mostobviously unstable.8.1.2 Apparatus and Set-UpRefer to Fig. 1. Place sample on a non-skid surface inclined at 10 in the orientation that is leaststable. The sample

23、 shall rest on the supporting surface without anchoring unless the installation instructions for the machine requirethat the sample be anchored to the floor. If this is the case, then anchor the specimen per the manufacturers recommendations.Determine how the user is placed on the machine to perform

24、 the exercise (that is, seating, standing, or prone) and then determinehow the users body weight is distributed onto the user support surfaces. For the simulated use test, a method of applying a steadystate load equal to 100 kg (220 lb) simulating the users weight and its distribution in the vertica

25、l direction at the point(s) of usercontact must be provided. As an example, for a seated user, the user support surface shall be adjusted to the uppermost position2For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at serviceastm.org. For Annual Boo

26、k of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3Available from CEN Management Centre, 36 rue de Stassart, B-1050, Brussels, Belgium.F2277 122(if adjustable) and the center of gravity of the 100 kg (220 lb) load shall be positioned approximatel

27、y 300 mm (12 in.) above theuser support surface. Possible methods of providing this load include, but are not limited to, pneumatic cylinder(s) or dead weights.8.1.3 CalibrationUsing an angle measuring instrument accurate to within 0.1, verify the non-skid surface is 10 6 0.5.Calibrate the load meas

28、urement apparatus to confirm accuracy to within 620 N (4.5 lb) over entire 981 N (220 lb) range.8.1.4 ProcedureTest the sample as follows:8.1.4.1 With the sample machine (no user load applied) positioned on the tilt surface, verify that the sample does not tip overwith the resistance means in the re

29、st position.8.1.4.2 Using the aforementioned load apparatus, distribute a vertical load equal to 100 kg (220 lb) 6 5 % in a non-impactmanner to the specimen where the user contacts the machine during normal operation. (If only a portion of the users body issupported by the machine during operation,

30、the 100 kg (220 lb) simulated user weight shall be reduced by the appropriate amount.)Raise and support the lifting arms and weight stack to simulate the furthest point in the range of travel as encountered duringnormal operation of the machine by a user of 1.8 m (74 in.) stature. Verify that the sa

31、mple does not tip over.8.1.4.3 Repeat 8.1.4.1 and 8.1.4.2 with the sample oriented in any other directions of potential instability.8.1.5 Pass/Fail CriteriaIn none of the above test conditions shall the sample tip over.8.1.6 Precision and BiasNo information is presented about either the precision or

32、 bias of test 8.1 for measuring stability sincethe test result is non-quantitative.8.2Edge Sharpness8.2 Weight Stack Travel:8.2.1The purpose of this test is to verify that there are no edges in the accessible area that would constitute a risk of injury. Wherethere is uncertainty, a sharp-edge tester

33、 as specified by UL 1439 is to be employed.8.2.1 This test is a visual inspection of the sample to ensure that the weight stack travels freely along its guide means and returnsto its initial position after the displacing force has been removed.8.2.2 Apparatus and Set UpThe sample shall be set up as

34、described in 7.1.8.2.3 CalibrationCalibrate sharp-edge tester per UL 1439. No calibration required. Visual inspection only.8.2.4 ProcedureExamine the accessible areas by visual and tactile means to ensure all parts are burr-free, rounded, orotherwise insufficiently sharp to constitute a risk of inju

35、ry. Wherever there may be uncertainty as to the sharpness of an edge, usethe edge tester and conduct the test per UL 1439. Move the lifting arm through its range of travel and verify that the weight stackFIG. 1 Tilt TestF2277 123moves along a guide means in a controlled manner and returns to its ini

36、tial position as the lifting arm is returned to its initial restposition.8.2.5 Pass/Fail CriteriaUse the pass/fail criteria of UL 1439 to determine if the sample passes this test. The weight stackmust begin and end the test in the same rest position and must not move unless it is displaced intention

37、ally by a lifting force appliedto the lifting arm.8.2.6 Precision and BiasNo information is presented about either the precision or bias of test in 8.2 for evaluating sharp edgessince the test result is non-quantitative.8.3Corner Sharpnessfor evaluating weight stack travel since the test result is n

38、on-quantitative.8.3 Weight Stack Selector Pin Retention:8.3.1This test is a visual inspection of the sample to ensure that all corners in the accessible areas are radiused or chamfered.8.3.1 This test is a visual and physical inspection of the weight stack selector pin to ensure that the design feat

39、ures a retentiondevice and that it functions properly.8.3.2 Apparatus and Set UpThe sample shall be set up as described in 7.1. . Obtain instructions or a descriptive explanationof the function of the weight stack selector pin from the manufacturer.8.3.3 CalibrationNo calibration required. Visual an

40、d function inspection only.8.3.4 ProcedureInspect all corners to verify that the corners have been radiused or chamfered. Inspect the weight stackselector pin and ensure that it features a retention device that will not allow the pin to be removed from the weight stack unlessit is intentionally remo

41、ved. Examples of retention devices include, but are not limited to, spring activated detent balls or a physicaldeformation of the pin and comparable retention zone on the weight plate. The operation of the retention system shall beself-evident. Insert the weight stack selector pin into a weight on t

42、he weight stack and verify that the retention mechanism functionsproperly.8.3.5 Pass/Fail CriteriaAll corners in the accessible area shall be radiused or chamfered. Weight stack selector pins thatdo not have a retention means shall fail this test. Retention mechanisms that do not function according

43、to the instructions providedby the manufacturer shall fail this test.8.3.6 Precision and BiasNo information is presented about either the precision or bias of test 8.3 for evaluating corners sincethe test result is non-quantitative.8.4Tube Ends and Non-Functional Holes:8.4.1This test is a visual ins

44、pection of the unit to ensure that all tube ends and non-functional holes in the accessible area areclosed off.8.4.2Apparatus and Set UpThe sample shall be set up as described in 7.1.8.4.3CalibrationNo calibration required. Visual inspection only.8.4.4ProcedureInspect all tube ends and surfaces in t

45、he accessible area to verify that the ends and non-functional holes areclosed off by other components, caps, plugs, or covers. Seat adjustment holes are exempt from this test.8.4.5Pass/Fail CriteriaAll tube ends in the accessible area shall be closed off or the EN 957-1 test probe shall not be able

46、tobe inserted.8.4.6Precision and BiasNo information is presented about either the precision or bias of test in 8.4 for evaluating tube endclosure since the test result is non-quantitative.8.5Weight Stack Travel:8.5.1This test is a visual inspection of the sample to ensure that the weight stack trave

47、ls freely along its guide means and returnsto its initial position after the displacing force has been removed.8.5.2Apparatus and Set UpThe sample shall be set up as described in 7.1.8.5.3CalibrationNo calibration required. Visual inspection only.8.5.4ProcedureMove the lifting arm through its range

48、of travel and verify that the weight stack moves along a guide meansin a controlled manner and returns to its initial position as the lifting arm is returned to its initial rest position.8.5.5Pass/Fail CriteriaThe weight stack must begin and end the test in the same rest position and must not move u

49、nless itis displaced intentionally by a lifting force applied to the lifting arm.8.5.6Precision and BiasNo information is presented about either the precision or bias of test in 8.5 for evaluating weight stacktravel since the test result is non-quantitative.8.6Weight Stack Selector Pin Retention:8.6.1This test is a visual and physical inspection of the weight stack selector pin to ensure that the design features a retentiondevice and that it functions properly.8.6.2Apparatus and Set UpThe sample shall be set up as described in 7.1