ASTM F2122-2005 Standard Practice for Treestand Safety Devices《Treestand安全设备的标准实施规程》.pdf

《ASTM F2122-2005 Standard Practice for Treestand Safety Devices《Treestand安全设备的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM F2122-2005 Standard Practice for Treestand Safety Devices《Treestand安全设备的标准实施规程》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 2122 05An American National StandardStandard Practice forTreestand Safety Devices1This standard is issued under the fixed designation F 2122; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision.

2、 A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice provides guidance for providing usersafety devices on treestands.1.2 The values stated are in inch-pound units and ar

3、e to beregarded as the standard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitati

4、ons prior to use.2. Referenced Documents2.1 ASTM Standards:2F 2121 Practice for Treestand LabelsF 2123 Practice for Treestand InstructionsF 2337 Test Method for Treestand Fall Arrest System3. Terminology3.1 The terminology and definitions in the referenced docu-ments are applicable to this practice.

5、3.2 Definitions:3.2.1 backbarthe adjustable component of a climbingtreestand or handclimber that engages the tree to providesupport. The backbar may be rigid or flexible.3.2.2 climbing sticka device to assist climbing a treeprimarily to a fixed position treestand. A structure that issecured to the t

6、ree and allows the user to support his weightand climb to the desired height on the tree.3.2.3 climbing treestanda treestand that provides both themeans to ascend the tree, and allow the user to remain at adesired elevation.3.2.4 fall arrest systema system that is assembled for thepurpose of arresti

7、ng an accidental fall of its user. A FASconsists of a full body harness, lanyard, anchorage means, andconnecting.3.2.5 full body harnessa component with a design ofstraps that is fastened about the person in a manner so as tocontain the torso and distribute the fall arrest forces over atleast the up

8、per thighs, pelvis, chest, and shoulders, with meansfor attaching it to other components or subsystems.3.2.6 handclimber, or climbing aida device to assistclimbing with a climbing treestand. A structure that allows theuser to support his weight when lifting a climbing treestandwith his legs.3.2.7 in

9、tegral seata treestand seat which is attached to thebase (where the user stands) platform.3.2.8 ladder treestanda treestand that is secured to thetree at the elevation where the platform is located. (The laddertreestand may be secured to the tree at other locations and hassteps that are used to reac

10、h the platform or hunting position.)3.2.9 non-climbing, fixed position or hang-on treestandatreestand that is secured to the tree at the elevation where it isused. (The user usually ascends the tree by some means andthen lifts the treestand to the desired position and secures it foruse.)3.2.10 platf

11、ormthe horizontal structural area of a tree-stand on which the user stands and/or places his feet.3.2.11 tripod or tower standa tripod or tower stand isconstructed to be self-supporting and is not required to besecured to a tree.3.2.12 two person treestanda ladder or hang-on treestanddesigned and ma

12、rketed for use by two persons simultaneously.4. Summary of Practice4.1 This practice provides guidelines for the selection,availability and placement of user safety devices on treestandsand climbing sticks particularly for quality assurance andadequacy of auxiliary safety including:4.1.1 Use of inst

13、ructions in anticipation of user error ormisuse.4.1.2 Availability of instructions in case of their loss.4.1.3 User fall protection (fall arrest system).4.1.4 Interconnects (two piece units).4.1.5 Auxiliary security.1This practice is under the jurisdiction of ASTM Committee F08 on SportsEquipment an

14、d Facilities and is the direct responsibility of Subcommittee F08.16 onArchery Products.Current edition approved Oct. 1, 2005. Published October 2005. Originallyapproved in 2001. Last previous edition approved in 2001 as F 2122 01.2For referenced ASTM standards, visit the ASTM website, www.astm.org,

15、 orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5. Significance

16、 and Use5.1 This practice is provided to develop and maintainuniformity in practices for availability, use, and selection ofsafety devices on treestands and climbing sticks, particularlywith regard to quality assurance and safety.5.2 It is emphasized that the use of these practices will notalter the

17、 validity of data determined with specific tests, butprovides guidance in the interpretation of test results (valid orinvalid) and guidance in the selection of a reasonable generalprovision in those instances where no standard exists today.6. Procedure6.1 It is recommended that manufacturers follow

18、the meth-ods of safety provisions so described herein. When unusual orspecial conditions require auxiliary safety devices, means ormethods not covered herein, the manufacturer shall be respon-sible for their development to assure adequate availability forthe user.6.2 Selection of Safety Devices:6.2.

19、1 User instructions shall be supplied with each indi-vidual unit and shall be in accordance with Practice F 2123.6.2.1.1 Instructions shall contain detailed information on theproper set up, use and safety precautions for the unit.6.2.2 Labels and warnings shall be placed on the unit inaccordance wit

20、h Practice F 2121.6.2.2.1 Notice of availability of instructions will be identi-fied on the unit as a part of required label information as givenin 6.2.2.6.2.3 A fall arrest system that meets Test Method F 2337shall be provided with each treestand as standard equipment.The fall arrest system capacit

21、y shall not be less than the ratedcapacity of the treestand, except for a two person treestand (see6.2.3.3).6.2.3.1 The fall arrest system shall have provision to besecured to the tree that the user climbs. It shall be soconstructed that the user is able to adjust and minimize thefree-fall length.6.

22、2.3.2 In the case of climbing treestands, the features of thefall arrest system shall include allowing the user to have itsecured to the tree while in the process of climbing the tree.6.2.3.3 For two person treestands, there shall be a fall arrestsystem provided for each person, that is, two FAS. Th

23、e fallarrest system rated capacity shall be a minimum of 300 lbs.6.2.3.4 Ladder treestands shall include means to stabilizethe ladder from pivoting about the ladder axis and secure it tothe tree prior to use. Crisscrossing rope, straps, or othermethods to secure the ladder treestand to the tree to p

24、reventpivoting prior to climbing is an example of such means.Instructions shall include proper installation and use.6.2.4 Two-piece climbing treestands (those without integralseats) specifically, those involving a “stand-up/sit-down” modeof ascending or descending a tree, shall include a flexibleint

25、erconnecting device to secure the upper and lower piecestogether and prevent them from separating.6.2.4.1 A cable, rope, strap or other similar interconnectingmeans, shall be configured such that it will not encumber theuser while climbing while prohibiting the lower part fromfalling if the lower pa

26、rt were to become disengaged from theuser.6.2.4.2 The use of a device to secure the upper piece (seat)whenever the user removes the load (standing) is highlyrecommended. An elastic cord, rope, strap, etc. should be anintegral component of the upper piece and its use explained inthe unit instructions

27、.6.3 Auxiliary safety devices shall be provided where addi-tional safety precautions can be made to further protect theuser. Examples include: anti-slip platform surfaces, backbarlocking devices or tie-offs (for climbing treestands, use ofhandclimbers for locking means, balance bars, etc.).6.3.1 For

28、 special cases or non-typical units, specific safetydevices shall be provided where applicable.7. Keywords7.1 backbar; climbing stick; platform; treestand; tripodAPPENDIX(Nonmandatory Information)X1. Additional InformationX1.1 This practice is provided for use by manufacturers oftreestands and testi

29、ng companies. Criteria has been developedfor certification of treestands and this practice is an integralpart of the certification. However, a treestand conforming tothis practice alone does not constitute certification and thosemanufacturers desiring certification must meet all applicablestandards

30、as a minimum requirement.F2122052ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof

31、 infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this s

32、tandard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake you

33、r views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F2122053