ASTM F842-2012 Standard Test Methods for Measuring the Forced Entry Resistance of Sliding Door Assemblies Excluding Glazing Impact 《测量水平滑动门组件 (不包括门窗玻璃) 的抗强制进入能力的标准试验方法》.pdf
《ASTM F842-2012 Standard Test Methods for Measuring the Forced Entry Resistance of Sliding Door Assemblies Excluding Glazing Impact 《测量水平滑动门组件 (不包括门窗玻璃) 的抗强制进入能力的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM F842-2012 Standard Test Methods for Measuring the Forced Entry Resistance of Sliding Door Assemblies Excluding Glazing Impact 《测量水平滑动门组件 (不包括门窗玻璃) 的抗强制进入能力的标准试验方法》.pdf(20页珍藏版)》请在麦多课文档分享上搜索。
1、Designation:F84204 Designation: F842 12Standard Test Methods forMeasuring the Forced Entry Resistance of Sliding DoorAssemblies, Excluding Glazing Impact1This standard is issued under the fixed designation F842; the number immediately following the designation indicates the year of originaladoption
2、or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope
3、1.1 These test methods determine the ability of sliding door assemblies to restrain, delay, or frustrate forced entry.1.2 For purposes of these test methods, sliding door assemblies are defined as described in 1.2.1-1.2.4 and as shown in Fig. 1.Sliding door assemblies with a combination of operable
4、panels and fixed panels (lites) shall be classified and tested separately foreach type.1.2.1 Type AA sliding door assembly which incorporates one or more sliding panels that lock to the jamb.1.2.2 Type BA sliding door assembly which incorporates one or more sliding panels that lock to an intermediat
5、e jamb.1.2.3 Type CA sliding door assembly which incorporates one or more sliding panels that abut and lock to other panels.1.2.4 Type DAsliding door assembly which incorporates one or more fixed or stationary panels that are designed not to open.NOTE 1See Fig. 1 for graphic depiction of sliding doo
6、r assembly types.1.3The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversionsto inch-pound units that are pr
7、ovided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicabi
8、lity of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:2E631 Terminology of Building Constructions2.2 AAMA Standard:3AAMA 1303.5 Voluntary Specifications for Forced Entry Resistant Aluminum Sliding Glass Doors2.3 CAWM Standards:3CAWM 300-96 Forced Entry Resistance Tests
9、 for Sliding Glass DoorsCMBSO 1-79 California Model Building Security Ordinance3. Terminology3.1 DefinitionsDefinitions for standard terminology can be found in Terminology E631.3.2 Definitions of Terms Specific to This Standard:3.2.1 door frame assembly, ndoor frame assembly, nthe combination of a
10、head, sill, and jambs surrounding and supportingfixed and sliding panels.3.2.2 fixed jamb stile, nfixed jamb stile, nvertical members of fixed or stationary panels adjacent to any jamb.3.2.3 intermediate jamb, nintermediate jamb, nvertical member of a frame other than the outermost vertical members.
11、3.2.4 locking device(s) (lock), nlocking device(s) (lock), none or more components of a sliding door assembly intended toresist opening of the sliding door panel from the exterior.1These test methods are under the jurisdiction of ASTM Committee E06 on Performance of Buildings and are the direct resp
12、onsibility of Subcommittee E06.51 onPerformance of Windows, Doors, Skylights and Curtain Walls.Current edition approved MarchJune 1, 2004.2012. Published March 2004.July 2012. Originally approved in 1983. Last previous edition approved in 19972004 asF84297.F842 04. DOI: 10.1520/F0842-04.10.1520/F084
13、2-12.2For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3Available from theAmericanArchitectural Manufacturers
14、Association (AAMA), 1827 Walden Office Square, Suite 550, Schaumburg, IL 60173, http:/www.aamanet.org.1This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technic
15、ally possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box
16、 C700, West Conshohocken, PA 19428-2959, United States.3.2.5 sliding door assembly, nsliding door assembly, na combination of one or more sliding door panels with or without oneor more fixed panels within a common frame.FIG. 1 Typical Horizontal Sliding Door Assembly Types (viewed from the exterior)
17、F842 1224. Summary of Test Method4.1 The procedure consists of mounting a sliding door specimen into a test assembly fixture which in turn is mounted to a wallsupport fixture, and, after removing all exterior fasteners and loose component items, specified loads and forces are applied to thesliding d
18、oor test specimen in a prescribed sequence. Following removal of all loads, a determination is made whether or not entrycan be gained through the sliding door test specimen from the exterior.5. Significance and Use5.1 These test methods are intended to establish a measure of resistance for sliding d
19、oor assemblies subjected to attacks (otherthan impacting glazing materials) by unskilled or opportunistic burglars. Resistance to higher levels of force generated by skilledburglary attack requires methods, such as alarms, communication, or apprehension systems, or special security glazing materials
20、more sophisticated than those evaluated by these test methods.5.2 Entry through a sliding door assembly can be accomplished by impacting or removing glazing materials. This method doesnot evaluate glazing materials for breakage or de-glazing. Other standards must be used to evaluate forced entry by
21、impacting orremoving glazing.5.3 Acceptance criteria for performance levels are a matter for authorities having specific jurisdiction to establish. Suggestedguidelines are found in Annex A1.6. Test Criteria6.1 Sliding Door Test SpecimenThe same sliding door assembly shall be used for all testing and
22、 shall contain panels havingthe greatest height and width for which approval is sought. Each unique panel/frame arrangement and locking arrangement shallbe tested.6.1.1 The construction of the sliding door test specimen, including all hardware, components, and arrangement of panels shallbe represent
23、ative of that for which acceptance is desired.6.1.2 The sliding door test specimen shall consist of the entire assembled unit, including frame, glazing, and anchorage assupplied by the manufacturer for installation in the building.6.1.3 Unless otherwise specified, the window test specimen shall cont
24、ain annealed glass the weakest code compliant safetyglazing for testing and shall be single glazed if designed for either single or double glazing, or double glazed if designedexclusively for multiple glazing. Products tested with glazing materials other than annealed glassthe weakest code compliant
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF8422012STANDARDTESTMETHODSFORMEASURINGTHEFORCEDENTRYRESISTANCEOFSLIDINGDOORASSEMBLIESEXCLUDINGGLAZINGIMPACT

链接地址:http://www.mydoc123.com/p-537388.html