ASTM F821 F821M-2001(2012) Standard Specification for Domestic Use Doors and Frames Steel Interior Marine《船舶内部钢门及门框的标准规范》.pdf
《ASTM F821 F821M-2001(2012) Standard Specification for Domestic Use Doors and Frames Steel Interior Marine《船舶内部钢门及门框的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM F821 F821M-2001(2012) Standard Specification for Domestic Use Doors and Frames Steel Interior Marine《船舶内部钢门及门框的标准规范》.pdf(6页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F821/F821M 01 (Reapproved 2012) An American National StandardStandard Specification forDomestic Use Doors and Frames, Steel, Interior, Marine1This standard is issued under the fixed designation F821/F821M; the number immediately following the designation indicates the yearof original ad
2、option or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the construction of standardand custom-built
3、 interior steel doors and frames for shipsincluding U.S. Coast Guard certificated vessels with domesticroutes.1.2 Doors and frames are to be hollow metal constructionwith the door insulated for sound or fire.1.3 The doors are intended for use in staterooms, lavatories,passageways, and other areas pr
4、otected from weather.1.4 The values stated in either inch-pound units or SI unitsare to be regarded separately as standard. Within the text, theSI units are shown in brackets. The values stated in eachsystem are not exact equivalents; therefore, each system mustbe used independently of the other.2.
5、Referenced Documents2.1 ASTM Standards:2A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for PressureVessels and for General ApplicationsA582/A582M Specification for Free-Machining StainlessSteel BarsA1008/A1008M Specification for Steel, Sheet, Cold-R
6、olled,Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, SolutionHardened, and Bake HardenableE136 Test Method for Behavior of Materials in a VerticalTube Furnace at 750C2.2 Code of Federal Regulations (CFR) Title 46Shipping:Subchapter DTank Vessels, Subp
7、art 32.57StructuralFire Protection3Subchapter HPassenger Vessels, Subpart 72.05Structural Fire Protection3Subchapter ICargo and Miscellaneous Vessels, Subpart92.07Structural Fire Protection3Subchapter TSmall Passenger Vessels, Subpart 177.300Hull Structure3Subchapter UOceanographic Vessels, Subpart
8、190.07Structural Fire Protection3Structural Insulations, Subpart 164.0073Structural Insulations, Subpart 164.1073Noncombustible Materials for Merchant Vessels, Subpart164.0093Noncombustible Materials, Subpart 164.10932.3 Builders Hardware Manufacturers Association, Inc.:A 156.18 Materials and Finish
9、es42.4 U.S. Public Health Service:Publication No. 393, Handbook on Sanitation of VesselConstruction53. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 hands of doorsa term used to describe a door fromthe outside or key side of the door.3.1.2 right-hand regular doora door having h
10、inges on theright side when swinging door away from the individualopening it.3.1.3 left-hand regular doora door having hinges on theleft side when swinging door away from the individual openingit.3.1.4 right-hand reverse bevel doora door having hingeson right side when swinging door towards the indi
11、vidualopening it.3.1.5 left-hand reverse bevel doora door having hinges onleft side when swinging door towards the individual opening it.3.1.6 face platesthe exterior metal skins that enclose theinternal supporting structure of the door.1This specification is under the jurisdiction of ASTM Committee
12、 F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved June 1, 2012. Published October 2012. Originallyapproved in 1983. Last previous edition approved in 2001 as F821/F821M - 01(2007)1. DOI: 10.1520/F0821_F
13、0821M-01R12.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from the Superintendent of Documents,
14、U.S. Government PrintingOffice, Washington, DC 20402.4Available from BHMA, Inc., 355 Lexington Ave., 17th Floor, New York, NY10017.5Available from United States Public Health Services, Division of EngineeringServices, Parklawn Library, Room 1315, 5600 Fishers Lane, Rockville, MD 20857,Attention: Ms.
15、 Bonnie Scott.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States13.1.7 latcha device normally installed in the vertical edgeof door, opposite hinge edge, that when latched retains door inclosed position.3.1.8 throwthe extension, or reach
16、, of the latch bolt. Thisthrow is measured from latch face plate to extreme outer edgeof latch bolt with latch bolt in fully extended position.3.1.9 padlock eyea means for securing door in closedposition by the use of a padlock.4. Classification4.1 Classes of doors and frames shall be as indicated i
17、n theordering information. (See Annex A1 for definition of variousclass divisions.)4.1.1 Class A-O for installation in Class A-O divisions.4.1.2 Class A for installation in Class A-15, A-30, and A-60divisions.4.1.3 Class B for installation in Class B divisions.4.1.4 Class C for installation in Class
18、 C divisions.4.2 Doors and frames shall be of the following types asindicated in ordering information.4.2.1 Type I standard doors are of the following widths.Height and details shall conform to Tables 1-6 and Figs. 1-3.Size 122-in. (559-mm) clear jamb widthSize 224-in. (610-mm) clear jamb widthSize
19、326-in. (660-mm) clear jamb widthSize 430-in. (762-mm) clear jamb widthSize 536-in. (914-mm) clear jamb width4.2.2 Type II doors conforming generally to specificationsbut requiring special requirements as indicated in the orderinginformation (see also 6.7.9).4.2.3 Type III double doors using two of
20、Type I doors.4.2.4 Type IV double doors using two of Type II doors.NOTE 1Door widths are approximately 114 in. (approximately 32mm) greater than clear jamb width.5. Ordering Information5.1 Orders for items under this specification shall includethe following information by the purchaser:5.1.1 Class A
21、-O, A, B, or C.5.1.2 Type, hand, clear jamb width, and sill height.5.1.3 Options such as vent grills, louvers, vision lights, andhose ports.5.1.4 Hardware, sill caps, lock sets, latches, door closers,and hold backs if other than manufacturers standard. Masterkeying of door locks will not be provided
22、 unless required anddefined by ordering documents. Instead, each door lock will bekeyed differently.5.1.5 Color chip and desired painting specifications or othercommercial designation for final finish. If not specified, doorswill have manufacturers prime coat applied.5.1.6 For Type II and III doors,
23、 sizes and any othersupplementary requirements.5.1.7 Sill Heights0 in. (0 mm), 112 in. (38 mm), or 6 in.(152 mm). See Figs. 1-3.5.1.8 Cut out for light switch; if not requested in orderingdata, no provisions will be made.6. Materials and Manufacture6.1 For typical design, see Figs. 1-3.6.2 Steel for
24、 doors and frames shall be cold-rolled sheet,commercial quality in accordance with Specification A1008/A1008M. Other materials shall be as indicated.6.3 Class A-O Doors (See Fig. 1 and Table 1 and Table 2):6.3.1 Door shall be 134-in. (45-mm) thick hollow steel with0.055-in. (1.4-mm) minimum face pla
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF821F821M20012012STANDARDSPECIFICATIONFORDOMESTICUSEDOORSANDFRAMESSTEELINTERIORMARINE 船舶 内部 门框 标准规范
链接地址:http://www.mydoc123.com/p-537330.html